This separates the setting of autoneg in i40e_phy_types_to_ethtool into
its own conditional. Doing this adds clarity as what PHYs
support/advertise autoneg and makes it easier to add new PHY types in
the future.
This also fixes an issue on devices with CRT_RETIMER where advertising
autoneg was being set, but supported autoneg was not.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's a number of minor incidental whitespace issues in this file.
This addresses most of the ones I could find.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Someone forgot a word in this comment and it's confusing without it.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function header erroneously listed 'phy_types' as a parameter. The
correct parameter is 'pf'.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes two issues in i40e_get_link_ksettings. It adds calls to
ethtool_link_ksettings_zero_link_mode to make sure advertising and
supported link masks are cleared before we start setting bits in them.
This also replaces some funky bit manipulations with a much nicer call
to ethtool_link_ksettings_del_link_mode when removing link modes.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Someone left this poor little function naked with no header. This
dresses it up in a proper function header it deserves.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This 'ifdef' doesn't accomplish anything so remove it.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After the switch to the new ethtool API, ethtool passes us
ethtool_ksettings structs instead of ethtool_command structs, however we
were still referring to them as 'cmd' variables. This renames them to
'ks' variables which makes the code easier to understand.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When using 'ethtool -L' on a VF to change number of requested queues
from PF, we shouldn't trust the VF to reset itself after making the
request. Doing it that way opens the door for a potentially malicious
VF to do nasty things to the PF which should never be the case.
This makes it such that after VF makes a successful request, PF will
then reset the VF to institute required changes. Only if the request
fails will PF send a message back to VF letting it know the request was
unsuccessful.
Testing-hints:
There should be no real functional changes. This is simply hardening
against a potentially malicious VF.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When querying the NVM for supported phy_types, on some firmware
versions, we were failing to actually fill out the phy_types which means
ethtool wouldn't report any link types.
Testing-hints:
Check 'ethtool <iface>' if you have the right (wrong?) firmware.
Without this patch, no link modes will be reported.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't populate const array patterns on the stack, instead make it
static. Makes the object code smaller by over 60 bytes:
Before:
text data bss dec hex filename
1953 496 0 2449 991 i40e_diag.o
After:
text data bss dec hex filename
1798 584 0 2382 94e i40e_diag.o
(gcc 6.3.0, x86-64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables setting up maximum Tx rates for the traffic
classes in i40e. The maximum rate is offloaded to the hardware through
the mqprio framework by specifying the mode option as 'channel' and
shaper option as 'bw_rlimit' and is configured for the VSI. Configuring
minimum Tx rate limit is not supported in the device. The minimum
usable value for Tx rate is 50Mbps.
Example:
# tc qdisc add dev eth0 root mqprio num_tc 2 map 0 0 0 0 1 1 1 1\
queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\
max_rate 4Gbit 5Gbit
To dump the bandwidth rates:
# tc qdisc show dev eth0
qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0
queues:(0:3) (4:7)
mode:channel
shaper:bw_rlimit max_rate:4Gbit 5Gbit
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors the BW rate limiting for Tx traffic
on the VF to be reused in the next patch for rate limiting Tx
traffic for the VSIs on the PF as well.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver is modified to enable the new mqprio hardware
offload mode and factor the TCs and queue configuration by
creating channel VSIs. In this mode, the priority to traffic
class mapping and the user specified queue ranges are used
to configure the traffic classes by setting the mode option to
'channel'.
Example:
map 0 0 0 0 1 2 2 3 queues 2@0 2@2 1@4 1@5\
hw 1 mode channel
qdisc mqprio 8038: root tc 4 map 0 0 0 0 1 2 2 3 0 0 0 0 0 0 0 0
queues:(0:1) (2:3) (4:4) (5:5)
mode:channel
shaper:dcb
The HW channels created are removed and all the queue configuration
is set to default when the qdisc is detached from the root of the
device.
This patch also disables setting up channels via ethtool (ethtool -L)
when the TCs are configured using mqprio scheduler.
The patch also limits setting ethtool Rx flow hash indirection
(ethtool -X eth0 equal N) to max queues configured via mqprio.
The Rx flow hash indirection input through ethtool should be
validated so that it is within in the queue range configured via
tc/mqprio. The bound checking is achieved by reporting the current
rss size to the kernel when queues are configured via mqprio.
Example:
map 0 0 0 1 0 2 3 0 queues 2@0 4@2 8@6 11@14\
hw 1 mode channel
Cannot set RX flow hash configuration: Invalid argument
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets up the infrastructure for offloading TCs and
queue configurations to the hardware by creating HW channels(VSI).
A new channel is created for each of the traffic class
configuration offloaded via mqprio framework except for the first TC
(TC0). TC0 for the main VSI is also reconfigured as per user provided
queue parameters. Queue counts that are not power-of-2 are handled by
reconfiguring RSS by reprogramming LUTs using the queue count value.
This patch also handles configuring the TX rings for the channels,
setting up the RX queue map for channel.
Also, the channels so created are removed and all the queue
configuration is set to default when the qdisc is detached from the
root of the device.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce a macro for the bit setting the PF reset flag and
update its usages. This makes it easier to use this flag
in functions to be introduced in future without encountering
checkpatch issues related to alignment and line over 80
characters.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It looks like we weren't correctly placing the pages from buffers that had
been used to return a filter programming status back on the ring. As a
result they were being overwritten and tracking of the pages was lost.
This change works to correct that by incorporating part of
i40e_put_rx_buffer into the programming status handler code. As a result we
should now be correctly placing the pages for those buffers on the
re-allocation list instead of letting them stay in place.
Fixes: 0e626ff7cc ("i40e: Fix support for flow director programming status")
Reported-by: Anders K. Pedersen <akp@cohaesio.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Anders K Pedersen <akp@cohaesio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Caller needs to acquire the lock. Called functions will not.
Fixes: 09f79fd49d ("i40e: avoid NVM acquire deadlock during NVM update")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a typo in i40e_vsi_alloc_arrays() documentation.
The first parameter name should be "vsi" instead of "type".
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The computed result of I40E_MAX_VSI_QP * I40E_VIRTCHNL_SUPPORTED_QTYPES
is used more than three times in function i40e_config_irq_link_list.
Simply declare a local variable to store it to improve readability.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- When the I2C is busy, the PHY reads are delayed. The firmware will
return EGAIN in these cases with an expectation that the SW will
trigger the reads again
- This patch retries the operation for a maximum period of 500ms
Signed-off-by: Jayaprakash Shanmugam <jayaprakash.shanmugam@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The find_first_bit function will return the size passed to search
if the first set bit is not found. This patch adds the check in case
that happens as the return value would be used as the index in an array
and that would have caused the out-of-bounds access.
Detected by CoverityScan, CID 1295969 Out-of-bounds access
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recently, the kernel gained support for enabling XPS and QoS at the
same time. Thus, we no longer need to worry about the number of
traffic classes when enabling XPS.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Double the number of descriptors we'll bundle into one tail bump when
receiving. Empirical testing has shown that we reduce CPU utilization
and don't appear to reduce throughput or packet rate. 32 seems to be the
sweet spot, as it's half the default polling budget, so we'd essentially
reduce from 4 tail writes when polling down to 2. Increasing this up to
64 appears to have negative impacts as it may become possible that we
don't bump the tail each time we get polled, which could cause a long
delay between returning descriptors to the hardware.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware only fetches descriptors on cachelines of 8, essentially
ignoring the lower 3 bits of the tail register. Thus, it is pointless to
bump tail by an unaligned access as the hardware will ignore some of the
new descriptors we allocated. Thus, it's ideal if we can ensure tail
writes are always aligned to 8.
At first, it seems like we'd already do this, since we allocate
descriptors in batches which are a multiple of 8. Since we'd always
increment by a multiple of 8, it seems like the value should always be
aligned.
However, this ignores allocation failures. If we fail to allocate
a buffer, our tail register will become unaligned. Once it has become
unaligned it will essentially be stuck unaligned until a buffer
allocation happens to fail at the exact amount necessary to re-align it.
We can do better, by simply rounding down the number of buffers we're
about to allocate (cleaned_count) such that "next_to_clean
+ cleaned_count" is rounded to the nearest multiple of 8.
We do this by calculating how far off that value is and subtracting it
from the cleaned_count. This essentially defers allocation of buffers if
they're going to be ignored by hardware anyways, and re-aligns our
next_to_use and tail values after a failure to allocate a descriptor.
This calculation ensures that we always align the tail writes in a way
the hardware expects and don't unnecessarily allocate buffers which
won't be fetched immediately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The lrxq thresh value tells hardware to immediately interrupt when there
are fewer than N*64 packets left in the ring.
Counter intuitively, empirical testing has shown that decreasing this
value from 2 to 1, and thus changing from an immediate interrupt at
fewer than 128 descriptors down to 64 descriptors causes a small
increase in the maximum total packets per second we can receive. This
increase occurs even when we're polling with interrupts masked, as the
hardware must still handle interrupts internally even if we've disabled
them in software.
Also reduce the value for any VFs we allocate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the past we changed driver behavior to not clear the PBA when
re-enabling interrupts. This change was motivated by the flawed belief
that clearing the PBA would cause a lost interrupt if a receive
interrupt occurred while interrupts were disabled.
According to empirical testing this isn't the case. Additionally, the
data sheet specifically says that we should set the CLEARPBA bit when
re-enabling interrupts in a polling setup.
This reverts commit 40d72a5098 ("i40e/i40evf: don't lose interrupts")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ITR register expects to be programmed in units of 2 microseconds.
Because of this, all of the drivers I40E_ITR_* constants are in terms of
this 2 microsecond register.
Unfortunately, the rx_itr_default value is expected to be programmed in
microseconds.
Effectively the driver defaults to an ITR value of half the expected
value (in terms of minimum microseconds between interrupts).
Fix this by changing the default values to be calculated using
ITR_REG_TO_USEC macro which indicates that we're converting from the
register units into microseconds.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces hash_for_each function with hash_for_each_safe
when calling __i40e_del_filter. The hash_for_each_safe function is
the right one to use when iterating over a hash table to safely remove
a hash entry. Otherwise, incorrect values may be read from freed memory.
Detected by CoverityScan, CID 1402048 Read from pointer after free
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we don't yet have more than 32 flags, we'll use a u32 for both the
hw_features and flag field. Should we gain more flags in the future, we
may need to convert to a u64 or separate flags out into two fields.
This was overlooked in the previous commit 2781de2134c4 ("i40e/i40evf:
organize and re-number feature flags"), where the feature flag was not
converted form u64 to u32.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we've reduced the number of flags, organize similar flags
together and re-number them accordingly.
Since we don't yet have more than 32 flags, we'll use a u32 for both the
hw_features and flag field. Should we gain more flags in the future, we
may need to convert to a u64 or separate flags out into two fields.
One alternative approach considered, but not implemented here, was to
use an enumeration for the flag variables, and create a macro
I40E_FLAG() which used string concatenation to generate BIT_ULL values.
This has the advantage of making the actual bit values compile-time
dynamic so that we do not need to worry about matching the order to the
bit value. However, this does produce a high level of code churn, and
makes it more difficult to read a dumped flags value when debugging.
Change-ID: I8653fff69453cd547d6fe98d29dfa9d8710387d1
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 6a7fded776 ("i40e: Fix RS bit update in Tx path and
disable force WB workaround") we've tried to "optimize" setting the
RS bit based around skb->xmit_more. This same logic was refactored
in commit 1dc8b53879 ("i40e: Reorder logic for coalescing RS bits"),
but ultimately was not functionally changed.
Using skb->xmit_more in this way is incorrect, because in certain
circumstances we may see a large number of skbs in sequence with
xmit_more set. This leads to a performance loss as the hardware does not
writeback anything for those packets, which delays the time it takes for
us to respond to the stack transmit requests. This significantly impacts
UDP performance, especially when layered with multiple devices, such as
bonding, VLANs, and vnet setups.
This was not noticed until now because it is difficult to create a setup
which reproduces the issue. It was discovered in a UDP_STREAM test in
a VM, connected using a vnet device to a bridge, which is connected to
a bonded pair of X710 ports in active-backup mode with a VLAN. These
layered devices seem to compound the number of skbs transmitted at once
by the qdisc. Additionally, the problem can be masked by reducing the
ITR value.
Since the original commit does not provide strong justification for this
RS bit "optimization", revert to the previous behavior of setting the RS
bit every 4th packet.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previous implementation of LED set/get functions required to enter
PHY debug mode, in order to prevent access to it from FW and SW at
the same time. Reset of all ports was a unwanted side effect.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements the PCI error handler reset_prepare and reset_done.
This allows us to handle function level reset. Without this patch we
are unable to perform and recover from an FLR correctly and this will cause
VFs to be unable to recover from an FLR on the PF.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there is no space for more flow director filters and user requested to
add a new one it is rejected by firmware and automatically removed from the
filter list maintained by driver. This behaviour is correct. Afterwards
existing filter can be removed making free slot for the new one. This
however causes the newly added filter to be accepted by firmware but
removed from driver filter list resulting in not showing after issuing
'ethtool -n <dev_name>'.
This happened due to not clearing the variable pf->fd_inv which stores
filter number to be removed from the list when firmware refused to add the
requested filter. It caused the filter with this specific ID to be
constantly removed once it was added to the list although it has been
accepted by firmware and effectively applied to the NIC.
It was fixed by clearing pf->fd_inv variable after removal of the filter
from the list when it was rejected by firmware.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch causes error message to be displayed when NIC detects
insertion of module that does not meet thermal requirements.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes some code that was accidentally added to
the wrong function with a merge error. Fixes: c53934c6d1
("i40e: fix: do not sleep in netdev_ops")
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When using set_bit and friends, we should be using actual
bitmaps, and fix all the locations where we might access
it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This register was defined incorrectly. Fix the increment value to 8, and
replace the iterator with _i to make the definition consistent with
other statistics registers.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since I40E_PHY_TYPE_MAX is used as an iterator, usually combined with
some sort of bit-shifting, it should only include actual PHY types and
not error cases. Move it up in the enum declaration so that loops only
iterate across valid PHY types.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Starting with XL710 FW 5.3 PTP L4 was disabled for XL710 due to a bug. The
bug has since been resolved in XL710 FW >6.0 and PTP L4 can now be
re-enabled on those devices with updated firmware.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, when setting up the IRQ for a q_vector, we set an affinity
hint based on the v_idx of that q_vector. Meaning a loop iterates on
v_idx, which is an incremental value, and the cpumask is created based
on this value.
This is a problem in systems with multiple logical CPUs per core (like in
simultaneous multithreading (SMT) scenarios). If we disable some logical
CPUs, by turning SMT off for example, we will end up with a sparse
cpu_online_mask, i.e., only the first CPU in a core is online, and
incremental filling in q_vector cpumask might lead to multiple offline
CPUs being assigned to q_vectors.
Example: if we have a system with 8 cores each one containing 8 logical
CPUs (SMT == 8 in this case), we have 64 CPUs in total. But if SMT is
disabled, only the 1st CPU in each core remains online, so the
cpu_online_mask in this case would have only 8 bits set, in a sparse way.
In general case, when SMT is off the cpu_online_mask has only C bits set:
0, 1*N, 2*N, ..., C*(N-1) where
C == # of cores;
N == # of logical CPUs per core.
In our example, only bits 0, 8, 16, 24, 32, 40, 48, 56 would be set.
Instead, we should only assign hints for CPUs which are online. Even
better, the kernel already provides a function, cpumask_local_spread()
which takes an index and returns a CPU, spreading the interrupts across
local NUMA nodes first, and then remote ones if necessary.
Since we generally have a 1:1 mapping between vectors and CPUs, there
is no real advantage to spreading vectors to local CPUs first. In order
to avoid mismatch of the default XPS hints, we'll pass -1 so that it
spreads across all CPUs without regard to the node locality.
Note that we don't need to change the q_vector->affinity_mask as this is
initialized to cpu_possible_mask, until an actual affinity is set and
then notified back to us.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By default, our devices do source pruning, that is, they drop receive
packets that have the source MAC matching one of the receive filters.
Unfortunately, this breaks ARP monitoring in channel bonding, as the
bonding driver expects devices to receive ARPs containing their own
source address.
Add an ethtool private flag to control this feature.
Also, remove the netif_running() check when we process our private
flags. It's OK to reset when the device is closed and in most cases we
need the reset the apply these changes.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a typo in i40e_pf object documentation; num_req_vfs
refers to the number of VFs requested for the PF.
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable i40e to pass traffic with VLAN tags using the 802.1ad ethernet
protocol ID (0x88a8).
This requires NIC firmware providing version 1.7 of the API. With
older NIC firmware 802.1ad tagged packets will continue to be dropped.
No VLAN offloads nor RSS are supported for 802.1ad VLANs.
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently there is a bug in which the PF driver fails to inform clients
of a VF reset which then causes clients to leak resources. The bug
exists because we were incorrectly checking the I40E_VF_STATE_PRE_ENABLE
bit.
When a VF is first init we go through a reset to initialize variables
and allocate resources but we don't want to inform clients of this first
reset since the client isn't fully enabled yet so we set a state bit
signifying we're in a "pre-enabled" client state. During the first
reset we should be clearing the bit, allowing all following resets to
notify the client of the reset when the bit is not set. This patch
fixes the issue by negating the 'test_and_clear_bit' check to accurately
reflect the behavior we want.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we inappropriately clear the vf_states variable with a null
assignment. This is problematic because we should be using atomic
bitops on this variable and we don't actually want to clear all the
flags. We should just clear the ones we know we want to clear.
Additionally remove the I40E_VF_STATE_FCOEENA bit because it is no
longer being used.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is possible although rare that we may not reset when
i40e_vc_disable_vf() is called. This can lead to some weird
circumstances with some values not being properly set. Modify
i40e_reset_vf() to return a code indicating whether it reset or not.
Now, i40e_vc_disable_vf() can wait until a reset actually occurs. If it
fails to free up within a reasonable time frame we'll display a warning
message.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace i40e_vc_notify_vf_reset and i40e_reset_vf with a call to
i40e_vc_disable_vf which does this exact thing. This matches similar
code patterns throughout the driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
