The official feature-complete WCN3680B driver (known as prima, open source
but not upstream) supports channels 136 and 144.
However, these channels are missing in upstream. Add them here to get
closer to feature parity with prima.
Signed-off-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025175359.3591048-3-benl@squareup.com
The official feature-complete WCN3680B driver (known as prima, open source
but not upstream) sends this feature bit.
As we wish to support the antenna diversity feature in upstream, we need
to set this bit as well.
Signed-off-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025175359.3591048-2-benl@squareup.com
The channel scan list must be updated before triggering a hardware scan
so that firmware takes into account the regulatory info for each single
channel such as active/passive config, power, DFS, etc... Without this
the firmware uses its own internal default channel configuration, which
is not aligned with mac80211 regulatory rules, and misses several
channels (e.g. 144).
Fixes: 2f3bef4b24 ("wcn36xx: Add hardware scan offload support")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635175328-25642-1-git-send-email-loic.poulain@linaro.org
Firmware link offload monitoring can be made to work in 3/4 cases by
switching on firmware feature bit WLANACTIVE_OFFLOAD
- Secure power-save on
- Secure power-save off
- Open power-save on
However, with an open AP if we switch off power-saving - thus never
entering Beacon Mode Power Save - BMPS, firmware never forwards loss
of beacon upwards.
We had hoped that WLANACTIVE_OFFLOAD and some fixes for sequence numbers
would unblock this but, it hasn't and further investigation is required.
Its possible to have a complete set of Secure power-save on/off and Open
power-save on/off provided we use Linux' link monitoring mechanism.
While we debug the Open AP failure we need to fix upstream.
This reverts commit c973fdad79f6eaf247d48b5fc77733e989eb01e1.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025093037.3966022-2-bryan.odonoghue@linaro.org
If the system is resumed because of an incoming packet, the wcn36xx RX
interrupts is fired before actual resuming of the wireless/mac80211
stack, causing any received packets to be simply dropped. E.g. a ping
request causes a system resume, but is dropped and so never forwarded
to the IP stack.
This change fixes that, disabling DMA interrupts on suspend to no pass
packets until mac80211 is resumed and ready to handle them.
Note that it's not incompatible with RX irq wake.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635150496-19290-1-git-send-email-loic.poulain@linaro.org
The firmware is offering features such as ARP offload, for which
firmware crafts its own (QoS)packets without waking up the host.
Point is that the sequence numbers generated by the firmware are
not in sync with the host mac80211 layer and can cause packets
such as firmware ARP reponses to be dropped by the AP (too old SN).
To fix this we need to let the firmware manages the sequence
numbers by its own (except for QoS null frames). There is a SN
counter for each QoS queue and one global/baseline counter for
Non-QoS.
Fixes: 84aff52e4f ("wcn36xx: Use sequence number allocated by mac80211")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635150336-18736-1-git-send-email-loic.poulain@linaro.org
This is essentially exactly following the dma_wmb()/dma_rmb() usage
instructions in Documentation/memory-barriers.txt.
The theoretical races here are:
1. DXE (the DMA Transfer Engine in the Wi-Fi subsystem) seeing the
dxe->ctrl & WCN36xx_DXE_CTRL_VLD write before the dxe->dst_addr_l
write, thus performing DMA into the wrong address.
2. CPU reading dxe->dst_addr_l before DXE unsets dxe->ctrl &
WCN36xx_DXE_CTRL_VLD. This should generally be harmless since DXE
doesn't write dxe->dst_addr_l (no risk of freeing the wrong skb).
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211023001528.3077822-1-benl@squareup.com
All wcn36xx controllers are supposed to support HT40 (and SGI40),
This doubles the maximum bitrate/throughput with compatible APs.
Tested with wcn3620 & wcn3680B.
Cc: stable@vger.kernel.org
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634737133-22336-1-git-send-email-loic.poulain@linaro.org
On an open AP when you pull the plug on the AP, if we are not already in
BMPS mode then the firmware will not generate a disconnection event.
Instead we need to monitor for failure to enter BMPS and treat a string of
failures as connection loss.
Secure AP connections don't appear to demonstrate this behavior so the
work-around is limited to open APs only.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211022140447.2846248-2-bryan.odonoghue@linaro.org
WCNSS RX DMA transfer support is limited to 3872 bytes, which is
enough for simple MPDUs (single MSDU), but not enough for cases
with A-MSDU (depending on max AMSDU size or max MPDU size).
In that case the MPDU is spread over multiple transfers, with the
first transfer containing the MPDU header and (at least) the first
A-MSDU subframe and additional transfer(s) containing the following
A-MSDUs. This can be handled with a series of flags to tagging the
first and last A-MSDU transfers.
In that case we have to bufferize and re-linearize the A-MSDU buffers
into a proper MPDU skb before forwarding to mac80211 (in the same way
as it is done in ath10k).
This change also includes sanity check of the buffer descriptor to
prevent skb overflow.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634557705-11120-1-git-send-email-loic.poulain@linaro.org
Until now, offload scanning for 5Ghz channels was considered broken.
However it was mostly a driver issue, caused by bad reporting of the
beacons/probe-resp bands and frequencies, which has been fixed.
We can now allow offload scan for 5GHz band, this reduces the scanning
time comparing to software driven scanning.
Note that offloaded scan is limited to 48 channels, check for this.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634554678-7993-2-git-send-email-loic.poulain@linaro.org
For packets originating from hardware scan, the channel and band is
included in the buffer descriptor (bd->rf_band & bd->rx_ch).
For 2Ghz band the channel value is directly reported in the 4-bit
rx_ch field. For 5Ghz band, the rx_ch field contains a mapping
index (given the 4-bit limitation).
The reserved0 value field is also used to extend 4-bit mapping to
5-bit mapping to support more than 16 5Ghz channels.
This change adds correct reporting of the frequency/band, that is
used in scan mechanism. And is required for 5Ghz hardware scan
support.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634554678-7993-1-git-send-email-loic.poulain@linaro.org
This change fix the TX ack mechanism in various ways:
- For NO_ACK tagged packets, we don't need to wait for TX_ACK indication
and so are not subject to the single packet ack limitation. So we don't
have to stop the tx queue, and can call the tx status callback as soon
as DMA transfer has completed.
- Fix skb ownership/reference. Only start status indication timeout
once the DMA transfer has been completed. This avoids the skb to be
both referenced in the DMA tx ring and by the tx_ack_skb pointer,
preventing any use-after-free or double-free.
- This adds a sanity (paranoia?) check on the skb tx ack pointer.
- Resume TX queue if TX status tagged packet TX fails.
Cc: stable@vger.kernel.org
Fixes: fdf21cc371 ("wcn36xx: Add TX ack support")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634567281-28997-1-git-send-email-loic.poulain@linaro.org
We observe unexpected connection drops with some APs due to
non-acked mac80211 generated null data frames (keep-alive).
After debugging and capture, we noticed that null frames are
submitted at standard data bitrate and that the given APs are
in trouble with that.
After setting the null frame bitrate to control bitrate, all
null frames are acked as expected and connection is maintained.
Not sure if it's a requirement of the specification, but it seems
the right thing to do anyway, null frames are mostly used for control
purpose (power-saving, keep-alive...), and submitting them with
a slower/simpler bitrate/modulation is more robust.
Cc: stable@vger.kernel.org
Fixes: 512b191d96 ("wcn36xx: Fix TX data path")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634560399-15290-1-git-send-email-loic.poulain@linaro.org
Idle Mode Power Save (IMPS) is a power saving mechanism which when called
by wcn36xx will cause the radio hardware to enter power collapse.
This particular call maps nicely to a simple conjunction/disjunction around
IEEE80211_CONF_CHANGE_IDLE and IEEE80211_CONF_IDLE.
Here we enter idle when we are not associated with an AP. The kernel will
incrementally toggle idle on/off in the process of trying to establish a
connection, thus saving power until we are connected to the AP again, at
which point we give way to BMPS if power_save is on.
We've validated that with IMPS an apq8039 device which has the wcn36xx
module loaded but, has not authenticated with an AP will get to VMIN on
suspend and will not without IMPS.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210909153320.2624649-1-bryan.odonoghue@linaro.org
Qcom documents suggest passing of negative values to the dump command,
however currently we convert from string to u32 not s32, so we cannot pass
a two's complement value to the firmware in this way.
There is in fact only one parameter which takes a two's complement value
<tigger threshold> in the antenna diversity switch command.
Downstream:
iwpriv wlan0 dump 71 3 <schedule period> <trigger threshold> <hysteresis value>
Upstream:
echo "71 3 <schedule period> <trigger threshold> <hysteresis value>" > /sys/kernel/debug/ieee80211/phy0/wcn36xx/dump
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210909144428.2564650-3-bryan.odonoghue@linaro.org
We have been tracking a strange bug with Antenna Diversity Switching (ADS)
on wcn3680b for a while.
ADS is configured like this:
A. Via a firmware configuration table baked into the NV area.
1. Defines if ADS is enabled.
2. Defines which GPIOs are connected to which antenna enable pin.
3. Defines which antenna/GPIO is primary and which is secondary.
B. WCN36XX_CFG_VAL(ANTENNA_DIVERSITY, N)
N is a bitmask of available antenna.
Setting N to 3 indicates a bitmask of enabled antenna (1 | 2).
Obviously then we can set N to 1 or N to 2 to fix to a particular
antenna and disable antenna diversity.
C. WCN36XX_CFG_VAL(ASD_PROBE_INTERVAL, XX)
XX is the number of beacons between each antenna RSSI check.
Setting this value to 50 means, every 50 received beacons, run the
ADS algorithm.
D. WCN36XX_CFG_VAL(ASD_TRIGGER_THRESHOLD, YY)
YY is a two's complement integer which specifies the RSSI decibel
threshold below which ADS will run.
We default to -60db here, meaning a measured RSSI <= -60db will
trigger an ADS probe.
E. WCN36XX_CFG_VAL(ASD_RTT_RSSI_HYST_THRESHOLD, Z)
Z is a hysteresis value, indicating a delta which the RSSI must
exceed for the antenna switch to be valid.
For example if HYST_THRESHOLD == 3 AntennaId1-RSSI == -60db and
AntennaId-2-RSSI == -58db then firmware will not switch antenna.
The threshold needs to be -57db or better to satisfy the criteria.
F. A firmware feature bit also exists ANTENNA_DIVERSITY_SELECTION.
This feature bit is used by the firmware to report if
ANTENNA_DIVERSITY_SELECTION is supported. The host is not required to
toggle this bit to enable or disable ADS.
ADS works like this:
A. Every XX beacons the firmware switches to or remains on the primary
antenna.
B. The firmware then sends a Request-To-Send (RTS) packet to the AP.
C. The firmware waits for a Clear-To-Send (CTS) response from the AP.
D. The firmware then notes the received RSSI on the CTS packet.
E. The firmware then repeats steps A-D on the secondary antenna.
F. Subsequently if the RSSI on the measured antenna is better than
ASD_TRIGGER_THRESHOLD + the active antenna's RSSI then the
measured antenna becomes the active antenna.
G. If RSSI rises past ASD_TRIGGER_THRESHOLD then ADS doesn't run at
all even if there is a substantially better RSSI on the alternative
antenna.
What we have been observing is that the RTS packet is being sent but the
MAC address is a byte-swapped version of the target MAC. The ADS/RTS MAC is
corrupted only when the link is encrypted, if the AP is open the RTS MAC is
correct. Similarly if we configure the firmware to an RTS/CTS sequence for
regular data - the transmitted RTS MAC is correctly formatted.
Internally the wcn36xx firmware uses the indexes in the SMD commands to
populate and extract data from specific entries in an STA lookup table. The
AP's MAC appears a number of times in different indexes within this lookup
table, so the MAC address extracted for the data-transmit RTS and the MAC
address extracted for the ADS/RTS packet are not the same STA table index.
Our analysis indicates the relevant firmware STA table index is
"bssSelfStaIdx".
There is an STA populate function responsible for formatting the MAC
address of the bssSelfStaIdx including byte-swapping the MAC address.
Its clear then that the required STA populate command did not run for
bssSelfStaIdx.
So taking a look at the sequence of SMD commands sent to the firmware we
see the following downstream when moving from an unencrypted to encrypted
BSS setup.
- WLAN_HAL_CONFIG_BSS_REQ
- WLAN_HAL_CONFIG_STA_REQ
- WLAN_HAL_SET_STAKEY_REQ
Upstream in wcn36xx we have
- WLAN_HAL_CONFIG_BSS_REQ
- WLAN_HAL_SET_STAKEY_REQ
The solution then is to add the missing WLAN_HAL_CONFIG_STA_REQ between
WLAN_HAL_CONFIG_BSS_REQ and WLAN_HAL_SET_STAKEY_REQ.
No surprise WLAN_HAL_CONFIG_STA_REQ is the routine responsible for
populating the STA lookup table in the firmware and once done the MAC sent
by the ADS routine is in the correct byte-order.
This bug is apparent with ADS but it is also the case that any other
firmware routine that depends on the "bssSelfStaIdx" would retrieve
malformed data on an encrypted link.
Fixes: 3e977c5c52 ("wcn36xx: Define wcn3680 specific firmware parameters")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210909144428.2564650-2-bryan.odonoghue@linaro.org
Firmware sends delete_sta_context_ind when it detects the AP has gone
away in STA mode. Right now the handler for that indication only handles
AP mode; fix it to also handle STA mode.
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210901180606.11686-1-benl@squareup.com
When receiving a beacon or probe response, we should update the
boottime_ns field which is the timestamp the frame was received at.
(cf mac80211.h)
This fixes a scanning issue with Android since it relies on this
timestamp to determine when the AP has been seen for the last time
(via the nl80211 BSS_LAST_SEEN_BOOTTIME parameter).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1629992768-23785-1-git-send-email-loic.poulain@linaro.org
The WLAN NV firmware blob differs between platforms, and possibly
devices, so add support in the wcn36xx driver for reading the path of
this file from DT in order to allow these files to live in a generic
file system (or linux-firmware).
For some reason the parent (wcnss_ctrl) also needs to upload this blob,
so rather than specifying the same information in both nodes wcn36xx
reads the string from the parent's of_node.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Aníbal Limón <anibal.limon@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210824171225.686683-1-bjorn.andersson@linaro.org
If the operating channel is the first in the scan list, it was seen that
a finish scan request would be sent before a start scan request was
sent, causing the firmware to fail all future scans. Track the current
channel being scanned to avoid requesting the scan finish before it
starts.
Cc: <stable@vger.kernel.org>
Fixes: 5973a29474 ("wcn36xx: Fix software-driven scan")
Signed-off-by: Joseph Gates <jgates@squareup.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1629286303-13179-1-git-send-email-loic.poulain@linaro.org
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring array fields.
Instead of writing past the end of the header to reach the rest of
the body, replace the redundant function with existing macro to wipe
struct contents and set field values. Additionally adjusts macro to add
missing parens.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210617171058.3410494-1-keescook@chromium.org
Right now wcn->hal_buf is allocated in wcn36xx_start(). This is a problem
since we should have setup all of the buffers we required by the time
ieee80211_register_hw() is called.
struct ieee80211_ops callbacks may run prior to mac_start() and therefore
wcn->hal_buf must be initialized.
This is easily remediated by moving the allocation to probe() taking the
opportunity to tidy up freeing memory by using devm_kmalloc().
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605173347.2266003-1-bryan.odonoghue@linaro.org
Enable flags for
- Magic packet
- GTK rekey
Previous patches implemented the necessary code to switch these two on.
Standalone magic packet absent GTK rekey is pretty useless, so it makes
sense to flag both at once.
Once done it is possible for wcn36xx firmware to
1. Respond to ipv4 and ipv6 ARP/NS lookup requests
2. Bring the system out of suspend when a magic packet is received.
Magic in our case is a simple ipv4 or ipv6 unicast.
3. GTK rekey whilst in suspend
Once we wake from suspend the GTK will be updated as necessary
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-13-bryan.odonoghue@linaro.org
This commit is the corresponding resume() path request to the firmware when
resuming. Unlike the suspend() version which is a unidirectional
indication, the resume version is a standard request/response.
Once the resume() request completes ipv4 ARP, ipv6 NS and GTK rekey offload
stop working and can subsequently be rolled back.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-12-bryan.odonoghue@linaro.org
In order to activate ipv4 ARP offload, ipv6 NS offload and firmware GTK
offload we need to send a unidirectional indication from host to wcn
indicating a transition to suspend.
Once done, firmware will respond to ARP broadcasts, ipv6 NS lookups and
perform GTK rekeys without waking the host.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-11-bryan.odonoghue@linaro.org
Having enabled GTK rekey in suspend, we need to extract the replay counter
from the firmware on resume and perform a ieee80211_gtk_rekey_notify() so
that the STA remains verified from the perspective of the AP.
In order to enable the SMD command and response we need to pack the
existing command/response structures. Given these structures are currently
unused, there's no need to backport this as a fix.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-10-bryan.odonoghue@linaro.org
Using previously set GTK KCK and KEK material this commit adds GTK rekeying
to the WoWLAN suspend/resume path. A small error in the packing of the
up to now unused command structure is fixed as we go.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-9-bryan.odonoghue@linaro.org
Add a callback for Group Temporal Key tracking as provided by the standard
WiFi ops structure.
We track the key to integrate GTK offloading into the WoWLAN suspend path
later on. Code comes from the Intel iwlwifi driver with minimal name
changes.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-8-bryan.odonoghue@linaro.org
We need to respond to ipv6 namespace lookups when in suspend. This patch
adds the necessary changes to issue the appropriate firmware command on
suspend and resume to enter/exit firmware offloaded ns lookup.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-7-bryan.odonoghue@linaro.org
Taking code from iwlwifi this commit adds a standard callback for
ipv6_addr_change().
This callback allows wcn36xx to know the set of ipv6 addresses. Something
we need to know in order to get wowlan working with ipv6.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-6-bryan.odonoghue@linaro.org
Testing on Android reveals that the flush on both suspend and resume of the
firmware indication work-queue can stall indefinitely.
Given this code path doesn't appear to have been exercised up until now,
removing this flush to unblock this situation.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-5-bryan.odonoghue@linaro.org
Add ARP offload support. Firmware is capable of responding to ARP requests
for a single ipv4 address only.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-4-bryan.odonoghue@linaro.org
A subsequent set of patches will extend out suspend/resume support in this
driver, we cannot set the firmware up for multiple ipv4/ipv6 addresses and
as such we can't iterate through a list of ieee80211_vif.
Constrain the interaction with the firmware to the first ieee80211_vif on
the suspend/resume/wowlan path.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-3-bryan.odonoghue@linaro.org
wcn36xx_smd_set_power_params() can return an error. For the purposes of
entering into suspend we need the suspend() function to trap and report
errors up the stack.
First step in this process is reporting the existing result code for
wcn36xx_smd_set_power_params().
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-2-bryan.odonoghue@linaro.org
memcpy operation is next to memset code, and the size to copy is equals to the size to
memset, so the memset operation is unnecessary, remove it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201223012516.24286-1-zhengyongjun3@huawei.com
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
warning by replacing a /* fall through */ comment with the new
pseudo-keyword macro fallthrough; instead of letting the code fall
through to the next case.
Notice that Clang doesn't recognize /* fall through */ comments as
implicit fall-through markings.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/f932c887e013767cbdabfdddd671086e8ae63193.1605896060.git.gustavoars@kernel.org
This commit updates the BMPS exit path to be consistent with downstream in
terms of exiting BMPS mode. Downstream sets the flag to send a NULL data
frame to the host on exiting BMPS.
This will tell the AP to send any queued frames to the STA immediately.
Verified the relevant bit toggle in wireshark.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201120021403.2646574-2-bryan.odonoghue@linaro.org
This patch calls wcn36xx_smd_keep_alive_req() on the STA patch immediately
after associating with an AP.
This will cause the firmware to send a NULL packet out to the AP every 30
seconds, thus offloading keep-alive processing from the SoC to the
firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-4-bryan.odonoghue@linaro.org
This patch switches on CONNECTION_MONITOR. Once done it is up to the
firmware to send keep alive and to monitor the link state.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-3-bryan.odonoghue@linaro.org
The firmware parameter LINK_FAIL_TX_CNT maps to the prima configuration
file parameter gLinkFailTxCnt and is described as:
quote: " If within gLinkFailTimeout period(values is mentioned in msec) if
FW doesn't receive acks for gLinkFailTxCnt number of packets, then
link will be disconnected."
The downstream description sets a minimum value of 1000 a maximum value of
60000 and a default value of 6000, however it appears that unless we
actually set this value deliberately firmware defaults it to 0.
Setting this value to non-zero results in the firmware doing link
monitoring. The working example from downstream paradoxically sets the
value to 200, here we opt to set the value to the minimum stipulated in the
configuration file 1000.
In conjunction with ieee80211_hw_set(wcn->hw, CONNECTION_MONITOR); this
change effects offload of link monitoring to the firmware.
Tested with:
'CNSS-PR-2-0-1-2-c1-74-130449-3' wcn3620
'CNSS-PR-2-0-1-2-c1-00083' wcn3680
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-2-bryan.odonoghue@linaro.org
In bmps mode, beacons are filtered, and firmware is in charge
of monitoring the beacons and report changes or loss.
mac80211 must be advertised about such change to prevent it's
internal timer based beacon monitor to report beacon loss.
Fix that by setting/clearing the IEEE80211_VIF_BEACON_FILTER
vif flag on bmps entry/exit.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592471863-31402-2-git-send-email-loic.poulain@linaro.org
This is a small update to fix an error I saw where a few functions do not
have a blank line in between them.
Affects smd.c and main.c - no logic is affected by this change.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150845.2179320-3-bryan.odonoghue@linaro.org
This commit marks all smd.c functions that are only used inside of smd.c as
static. Previous commits added some VHT specific setup functions non-static
which is the right thing to do in terms of having granular git commits that
compile warning free. What we really want is for local not global scope on
those functions.
This patch makes the conversion from global to local scope.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150845.2179320-2-bryan.odonoghue@linaro.org
This patch adds ieee802.11 VHT flags for the wcn3680b.
- RX_STBC1
- SU Beamformee
- MU Beamformee
- VHT80 SGI
- Single spatial stream
RX LDPC is declared as supported in the datasheet but not enabled at this
time.
After this patch is applied an AP should see the wcn3680 as an 802.11ac
capable device.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-5-bryan.odonoghue@linaro.org
This commit adds VHT rates to the wcn36xx_update_allowed_rates() routine.
Thus allowing the driver to latch the declared rates and transmit them to
the firmware in the same way as other 80211.n rates are.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-4-bryan.odonoghue@linaro.org
In order to send VHT parameters to wcn3680 we need to pass the extended V1
parameter structures to the firmware. These commands need to have the
version number set to 1.
This patch makes the conversion. The conversion consists of
1. Setting the version number for wcn3680 or leaving it at 0 otherwise
2. Setting the size of the packet header lower for wcn3620 and wcn3660
Once done all three chips can continue to use the same code to pass
parameters to their respective firmware. In the case of the wcn3680 the
passed structures will be slightly larger to accommodate communication of
VHT descriptors.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-3-bryan.odonoghue@linaro.org
