AMD proceessors define an address range that is reserved by HyperTransport
and causes a failure if used for guest physical addresses. Avoid
selftests failures by reserving those guest physical addresses; the
rules are:
- On parts with <40 bits, its fully hidden from software.
- Before Fam17h, it was always 12G just below 1T, even if there was more
RAM above this location. In this case we just not use any RAM above 1T.
- On Fam17h and later, it is variable based on SME, and is either just
below 2^48 (no encryption) or 2^43 (encryption).
Fixes: ef4c9f4f65 ("KVM: selftests: Fix 32-bit truncation of vm_get_max_gfn()")
Cc: stable@vger.kernel.org
Cc: David Matlack <dmatlack@google.com>
Reported-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210805105423.412878-1-pbonzini@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Tested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Recent kernels have checks to ensure the GPA values in special-purpose
registers like CR3 are within the maximum physical address range and
don't overlap with anything in the upper/reserved range. In the case of
SEV kselftest guests booting directly into 64-bit mode, CR3 needs to be
initialized to the GPA of the page table root, with the encryption bit
set. The kernel accounts for this encryption bit by removing it from
reserved bit range when the guest advertises the bit position via
KVM_SET_CPUID*, but kselftests currently call KVM_SET_SREGS as part of
vm_vcpu_add_default(), before KVM_SET_CPUID*.
As a result, KVM_SET_SREGS will return an error in these cases.
Address this by moving vcpu_set_cpuid() (which calls KVM_SET_CPUID*)
ahead of vcpu_setup() (which calls KVM_SET_SREGS).
While there, address a typo in the assertion that triggers when
KVM_SET_SREGS fails.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-Id: <20211006203617.13045-1-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Nathan Tempelman <natet@google.com>
- Add MTE support in guests, complete with tag save/restore interface
- Reduce the impact of CMOs by moving them in the page-table code
- Allow device block mappings at stage-2
- Reduce the footprint of the vmemmap in protected mode
- Support the vGIC on dumb systems such as the Apple M1
- Add selftest infrastructure to support multiple configuration
and apply that to PMU/non-PMU setups
- Add selftests for the debug architecture
- The usual crop of PMU fixes
-----BEGIN PGP SIGNATURE-----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=fWBV
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 updates for v5.14.
- Add MTE support in guests, complete with tag save/restore interface
- Reduce the impact of CMOs by moving them in the page-table code
- Allow device block mappings at stage-2
- Reduce the footprint of the vmemmap in protected mode
- Support the vGIC on dumb systems such as the Apple M1
- Add selftest infrastructure to support multiple configuration
and apply that to PMU/non-PMU setups
- Add selftests for the debug architecture
- The usual crop of PMU fixes
This test exercises the feature KVM_CAP_EXIT_ON_EMULATION_FAILURE. When
enabled, errors in the in-kernel instruction emulator are forwarded to
userspace with the instruction bytes stored in the exit struct for
KVM_EXIT_INTERNAL_ERROR. So, when the guest attempts to emulate an
'flds' instruction, which isn't able to be emulated in KVM, instead
of failing, KVM sends the instruction to userspace to handle.
For this test to work properly the module parameter
'allow_smaller_maxphyaddr' has to be set.
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <20210510144834.658457-3-aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add x86-64 hugepage support in the form of a x86-only variant of
virt_pg_map() that takes an explicit page size. To keep things simple,
follow the existing logic for 4k pages and disallow creating a hugepage
if the upper-level entry is present, even if the desired pfn matches.
Opportunistically fix a double "beyond beyond" reported by checkpatch.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210622200529.3650424-19-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In preparation for adding hugepage support, replace "pageMapL4Entry",
"pageDirectoryPointerEntry", and "pageDirectoryEntry" with a common
"pageUpperEntry", and add a helper to create an upper level entry. All
upper level entries have the same layout, using unique structs provides
minimal value and requires a non-trivial amount of code duplication.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210622200529.3650424-18-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a helper to retrieve a PTE pointer given a PFN, address, and level
in preparation for adding hugepage support.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210622200529.3650424-17-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename the "address" field to "pfn" in x86's page table structs to match
reality.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210622200529.3650424-16-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a helper to allocate a page for use in constructing the guest's page
tables. All architectures have identical address and memslot
requirements (which appear to be arbitrary anyways).
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210622200529.3650424-15-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop the memslot param from virt_pg_map() and virt_map() and shove the
hardcoded '0' down to the vm_phy_page_alloc() calls.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210622200529.3650424-13-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop the memslot param(s) from vm_vaddr_alloc() now that all callers
directly specific '0' as the memslot. Drop the memslot param from
virt_pgd_alloc() as well since vm_vaddr_alloc() is its only user.
I.e. shove the hardcoded '0' down to the vm_phy_pages_alloc() calls.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Switch to the vm_vaddr_alloc_page() helper for x86-64's "kernel"
allocations now that the helper uses the same min virtual address as the
open coded versions.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210622200529.3650424-9-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Refactor x86's GDT/TSS allocations to for memslot '0' at its
vm_addr_alloc() call sites instead of passing in '0' from on high. This
is a step toward using a common helper for allocating pages.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210622200529.3650424-5-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 22f232d134 ("KVM: selftests: x86: Set supported CPUIDs on
default VM") moved vcpu_set_cpuid into vm_create_with_vcpus, but
dirty_log_test doesn't use it to create vm. So vcpu's CPUIDs is
not set, the guest's pa_bits in kvm would be smaller than the
value queried by userspace.
However, the dirty track memory slot is in the highest GPA, the
reserved bits in gpte would be set with wrong pa_bits.
For shadow paging, page fault would fail in permission_fault and
be injected into guest. Since guest doesn't have idt, it finally
leads to vm_exit for triple fault.
Move vcpu_set_cpuid into vm_vcpu_add_default to set supported
CPUIDs on default vcpu, since almost all tests need it.
Fixes: 22f232d134 ("KVM: selftests: x86: Set supported CPUIDs on default VM")
Signed-off-by: Hou Wenlong <houwenlong93@linux.alibaba.com>
Message-Id: <411ea2173f89abce56fc1fca5af913ed9c5a89c9.1624351343.git.houwenlong93@linux.alibaba.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
x86, the only arch implementing exception handling, reports unhandled
vectors using port IO at a specific port number. This replicates what
ucall already does.
Introduce a new ucall type, UCALL_UNHANDLED, for guests to report
unhandled exceptions. Then replace the x86 unhandled vector exception
reporting to use it instead of port IO. This new ucall type will be
used in the next commits by arm64 to report unhandled vectors as well.
Tested: Forcing a page fault in the ./x86_64/xapic_ipi_test
halter_guest_code() shows this:
$ ./x86_64/xapic_ipi_test
...
Unexpected vectored event in guest (vector:0xe)
Signed-off-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210611011020.3420067-4-ricarkol@google.com
Rename the vm_handle_exception function to a name that indicates more
clearly that it installs something: vm_install_exception_handler.
Reported-by: kernel test robot <oliver.sang@intel.com>
Suggested-by: Marc Zyngier <maz@kernel.org>
Suggested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210611011020.3420067-2-ricarkol@google.com
If a KVM selftest is run on a machine without /dev/kvm, it will exit
silently. Make it easy to tell what's happening by printing an error
message.
Opportunistically consolidate all codepaths that open /dev/kvm into a
single function so they all print the same message.
This slightly changes the semantics of vm_is_unrestricted_guest() by
changing a TEST_ASSERT() to exit(KSFT_SKIP). However
vm_is_unrestricted_guest() is only called in one place
(x86_64/mmio_warning_test.c) and that is to determine if the test should
be skipped or not.
Signed-off-by: David Matlack <dmatlack@google.com>
Message-Id: <20210511202120.1371800-1-dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The variable in practice will never be uninitialized, because the
loop will always go through at least one iteration.
In case it would not, make vcpu_get_cpuid report an assertion
failure.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hyper-V emulation is enabled in KVM unconditionally. This is bad at least
from security standpoint as it is an extra attack surface. Ideally, there
should be a per-VM capability explicitly enabled by VMM but currently it
is not the case and we can't mandate one without breaking backwards
compatibility. We can, however, check guest visible CPUIDs and only enable
Hyper-V emulation when "Hv#1" interface was exposed in
HYPERV_CPUID_INTERFACE.
Note, VMMs are free to act in any sequence they like, e.g. they can try
to set MSRs first and CPUIDs later so we still need to allow the host
to read/write Hyper-V specific MSRs unconditionally.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210126134816.1880136-14-vkuznets@redhat.com>
[Add selftest vcpu_set_hv_cpuid API to avoid breaking xen_vmcall_test. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_get_supported_hv_cpuid() may come handy in all Hyper-V related tests.
Split it off hyperv_cpuid test, create system-wide and vcpu versions.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210126134816.1880136-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 181f494888 ("KVM: x86: fix CPUID entries returned by
KVM_GET_CPUID2 ioctl") revealed that we're not testing KVM_GET_CPUID2
ioctl at all. Add a test for it and also check that from inside the guest
visible CPUIDs are equal to it's output.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210129161821.74635-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This test will check the effect of various CPUID settings on the
MSR_IA32_PERF_CAPABILITIES MSR, check that whatever user space writes
with KVM_SET_MSR is _not_ modified from the guest and can be retrieved
with KVM_GET_MSR, and check that invalid LBR formats are rejected.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20210201051039.255478-12-like.xu@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The code is almost 100% the same anyway. Just move it to common
and add a few arch-specific macros.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-Id: <20201111122636.73346-5-drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a set of tests that ensure the guest cannot access paravirtual msrs
and hypercalls that have been disabled in the KVM_CPUID_FEATURES leaf.
Expect a #GP in the case of msr accesses and -KVM_ENOSYS from
hypercalls.
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Oliver Upton <oupton@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Reviewed-by: Aaron Lewis <aaronlewis@google.com>
Message-Id: <20201027231044.655110-7-oupton@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the infrastructure needed to enable exception handling in selftests.
This allows any of the exception and interrupt vectors to be overridden
in the guest.
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Reviewed-by: Alexander Graf <graf@amazon.com>
Message-Id: <20201012194716.3950330-4-aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix the layout of 'struct desc64' to match the layout described in the
SDM Vol 3, Chapter 3 "Protected-Mode Memory Management", section 3.4.5
"Segment Descriptors", Figure 3-8 "Segment Descriptor". The test added
later in this series relies on this and crashes if this layout is not
correct.
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Reviewed-by: Alexander Graf <graf@amazon.com>
Message-Id: <20201012194716.3950330-2-aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Changed all tests and utilities to use TEST_FAIL macro
instead of TEST_ASSERT(false,...).
Signed-off-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move function documentation comment blocks to the header files in
order to avoid duplicating them for each architecture. While at
it clean up and fix up the comment blocks.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Ensure that IA32_XSS appears in KVM_GET_MSR_INDEX_LIST if it can be set
to a non-zero value.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Change-Id: Ia2d644f69e2d6d8c27d7e0a7a45c2bf9c42bf5ff
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When KVM_GET_MSRS fail the report looks like
==== Test Assertion Failure ====
lib/x86_64/processor.c:1089: r == nmsrs
pid=28775 tid=28775 - Argument list too long
1 0x000000000040a55f: vcpu_save_state at processor.c:1088 (discriminator 3)
2 0x00000000004010e3: main at state_test.c:171 (discriminator 4)
3 0x00007fb8e69223d4: ?? ??:0
4 0x0000000000401287: _start at ??:?
Unexpected result from KVM_GET_MSRS, r: 36 (failed at 194)
and it's not obvious that '194' here is the failed MSR index and that
it's printed in hex. Change that.
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The naming VM_MODE_P52V48_4K is explicit but unclear when used on
x86_64 machines, because x86_64 machines are having various physical
address width rather than some static values. Here's some examples:
- Intel Xeon E3-1220: 36 bits
- Intel Core i7-8650: 39 bits
- AMD EPYC 7251: 48 bits
All of them are using 48 bits linear address width but with totally
different physical address width (and most of the old machines should
be less than 52 bits).
Let's create a new guest mode called VM_MODE_PXXV48_4K for current
x86_64 tests and make it as the default to replace the old naming of
VM_MODE_P52V48_4K because it shows more clearly that the PA width is
not really a constant. Meanwhile we also stop assuming all the x86
machines are having 52 bits PA width but instead we fetch the real
vm->pa_bits from CPUID 0x80000008 during runtime.
We currently make this exclusively used by x86_64 but no other arch.
As a slight touch up, moving DEBUG macro from dirty_log_test.c to
kvm_util.h so lib can use it too.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
state_test and smm_test are failing on older processors that do not
have xcr0. This is because on those processor KVM does provide
support for KVM_GET/SET_XSAVE (to avoid having to rely on the older
KVM_GET/SET_FPU) but not for KVM_GET/SET_XCRS.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is the initial implementation for KVM selftests on s390.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=STwX
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: add kselftests
This is the initial implementation for KVM selftests on s390.
- Add support for chained PMU counters in guests
- Improve SError handling
- Handle Neoverse N1 erratum #1349291
- Allow side-channel mitigation status to be migrated
- Standardise most AArch64 system register accesses to msr_s/mrs_s
- Fix host MPIDR corruption on 32bit
-----BEGIN PGP SIGNATURE-----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=yfCs
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm updates for 5.3
- Add support for chained PMU counters in guests
- Improve SError handling
- Handle Neoverse N1 erratum #1349291
- Allow side-channel mitigation status to be migrated
- Standardise most AArch64 system register accesses to msr_s/mrs_s
- Fix host MPIDR corruption on 32bit
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
Based on 1 normalized pattern(s):
this work is licensed under the terms of the gnu gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 48 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081204.624030236@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running with /sys/module/kvm_intel/parameters/unrestricted_guest=N,
test that a kernel warning does not occur informing us that
vcpu->mmio_needed=1. This can happen when KVM_RUN is called after a
triple fault.
This test was made to detect a bug that was reported by Syzkaller
(https://groups.google.com/forum/#!topic/syzkaller/lHfau8E3SOE) and
fixed with commit bbeac2830f ("KVM: X86: Fix residual mmio emulation
request to userspace").
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will be required later for tests like the kvm_create_max_vcpus
test that do not use the vm_create_default() function.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190523164309.13345-5-thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
So far the KVM selftests are compiled without any compiler warnings
enabled. That's quite bad, since we miss a lot of possible bugs this
way. Let's enable at least "-Wall" and some other useful warning flags
now, and fix at least the trivial problems in the code (like unused
variables).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a simple test for SMM, based on VMX. The test implements its own
sync between the guest and the host as using our ucall library seems to
be too cumbersome: SMI handler is happening in real-address mode.
This patch also fixes KVM_SET_NESTED_STATE to happen after
KVM_SET_VCPU_EVENTS, in fact it places it last. This is because
KVM needs to know whether the processor is in SMM or not.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Starting state migration after an IO exit without first completing IO
may result in test failures. We already have two tests that need this
(this patch in fact fixes evmcs_test, similar to what was fixed for
state_test in commit 0f73bbc851, "KVM: selftests: complete IO before
migrating guest state", 2019-03-13) and a third is coming. So, move the
code to vcpu_save_state, and while at it do not access register state
until after I/O is complete.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename VM_MODE_FLAT48PG to be more descriptive of its config and add a
new config that has the same parameters, except with 64K pages.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tidy up kvm-util code: code/comment formatting, remove unused code,
and move x86 specific code out. We also move vcpu_dump() out of
common code, because not all arches (AArch64) have KVM_GET_REGS.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
