The descriptor that ntu is pointing at when we exit
ice_alloc_rx_bufs_zc() should not have its corresponding DD bit cleared
as descriptor is not allocated in there and it is not valid for HW
usage.
The allocation routine at the entry will fill the descriptor that ntu
points to after it was set to ntu + nb_buffs on previous call.
Even the spec says:
"The tail pointer should be set to one descriptor beyond the last empty
descriptor in host descriptor ring."
Therefore, step away from clearing the status_error0 on ntu + nb_buffs
descriptor.
Fixes: db804cfc21 ("ice: Use the xsk batched rx allocation interface")
Reported-by: Elza Mathew <elza.mathew@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The 'if (ntu == rx_ring->count)' block in ice_alloc_rx_buffers_zc()
was previously residing in the loop, but after introducing the
batched interface it is used only to wrap-around the NTU descriptor,
thus no more need to assign 'xdp'.
Fixes: db804cfc21 ("ice: Use the xsk batched rx allocation interface")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the zero-copy data path is reusing the memory region that was
initially allocated for an array of struct ice_rx_buf for its own
purposes. This is error prone as it is based on the ice_rx_buf struct
always being the same size or bigger than what the zero-copy path needs.
There can also be old values present in that array giving rise to errors
when the zero-copy path uses it.
Fix this by freeing the ice_rx_buf region and allocating a new array for
the zero-copy path that has the right length and is initialized to zero.
Fixes: 57f7f8b6bc ("ice: Use xdp_buf instead of rx_buf for xsk zero-copy")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently we only NULL the xdp_buff pointer in the internal SW ring but
we never give it back to the xsk buffer pool. This means that buffers
can be leaked out of the buff pool and never be used again.
Add missing xsk_buff_free() call to the routine that is supposed to
clean the entries that are left in the ring so that these buffers in the
umem can be used by other sockets.
Also, only go through the space that is actually left to be cleaned
instead of a whole ring.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.
This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.
Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:
* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
(the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17
Fixes: e84db72727 ("ixgbe: Introduce function to control MDIO speed")
Signed-off-by: Cyril Novikov <cnovikov@lynx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit a296d665ea ("ixgbe: Add ethtool support to enable 2.5 and 5.0
Gbps support") introduced suppression of the advertisement of NBASE-T
speeds by default, according to Todd Fujinaka to accommodate customers
with network switches which could not cope with advertised NBASE-T
speeds, as posted in the E1000-devel mailing list:
https://sourceforge.net/p/e1000/mailman/message/37106269/
However, the suppression was not documented at all, nor was how to
enable NBASE-T support.
Properly document the NBASE-T suppression and how to enable NBASE-T
support.
Fixes: a296d665ea ("ixgbe: Add ethtool support to enable 2.5 and 5.0 Gbps support")
Reported-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The LTR maximum value was incorrectly written using the scale from
the LTR minimum value. This would cause incorrect values to be sent,
in cases where the initial calculation lead to different min/max scales.
Fixes: 707abf0695 ("igc: Add initial LTR support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In `igbvf_probe`, if register_netdev() fails, the program will go to
label err_hw_init, and then to label err_ioremap. In free_netdev() which
is just below label err_ioremap, there is `list_for_each_entry_safe` and
`netif_napi_del` which aims to delete all entries in `dev->napi_list`.
The program has added an entry `adapter->rx_ring->napi` which is added by
`netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has
been freed below label err_hw_init. So this a UAF.
In terms of how to patch the problem, we can refer to igbvf_remove() and
delete the entry before `adapter->rx_ring`.
The KASAN logs are as follows:
[ 35.126075] BUG: KASAN: use-after-free in free_netdev+0x1fd/0x450
[ 35.127170] Read of size 8 at addr ffff88810126d990 by task modprobe/366
[ 35.128360]
[ 35.128643] CPU: 1 PID: 366 Comm: modprobe Not tainted 5.15.0-rc2+ #14
[ 35.129789] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[ 35.131749] Call Trace:
[ 35.132199] dump_stack_lvl+0x59/0x7b
[ 35.132865] print_address_description+0x7c/0x3b0
[ 35.133707] ? free_netdev+0x1fd/0x450
[ 35.134378] __kasan_report+0x160/0x1c0
[ 35.135063] ? free_netdev+0x1fd/0x450
[ 35.135738] kasan_report+0x4b/0x70
[ 35.136367] free_netdev+0x1fd/0x450
[ 35.137006] igbvf_probe+0x121d/0x1a10 [igbvf]
[ 35.137808] ? igbvf_vlan_rx_add_vid+0x100/0x100 [igbvf]
[ 35.138751] local_pci_probe+0x13c/0x1f0
[ 35.139461] pci_device_probe+0x37e/0x6c0
[ 35.165526]
[ 35.165806] Allocated by task 366:
[ 35.166414] ____kasan_kmalloc+0xc4/0xf0
[ 35.167117] foo_kmem_cache_alloc_trace+0x3c/0x50 [igbvf]
[ 35.168078] igbvf_probe+0x9c5/0x1a10 [igbvf]
[ 35.168866] local_pci_probe+0x13c/0x1f0
[ 35.169565] pci_device_probe+0x37e/0x6c0
[ 35.179713]
[ 35.179993] Freed by task 366:
[ 35.180539] kasan_set_track+0x4c/0x80
[ 35.181211] kasan_set_free_info+0x1f/0x40
[ 35.181942] ____kasan_slab_free+0x103/0x140
[ 35.182703] kfree+0xe3/0x250
[ 35.183239] igbvf_probe+0x1173/0x1a10 [igbvf]
[ 35.184040] local_pci_probe+0x13c/0x1f0
Fixes: d4e0fe01a3 (igbvf: add new driver to support 82576 virtual functions)
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Letu Ren <fantasquex@gmail.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Move checking condition of VF MAC filter before clearing
or adding MAC filter to VF to prevent potential blackout caused
by removal of necessary and working VF's MAC filter.
Fixes: 1b8b062a99 ("igb: add VF trust infrastructure")
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver has to check if it does not accidentally put the timestamp in
the SKB before previous timestamp gets overwritten.
Timestamp values in the PHY are read only and do not get cleared except
at hardware reset or when a new timestamp value is captured.
The cached_tstamp field is used to detect the case where a new timestamp
has not yet been captured, ensuring that we avoid sending stale
timestamp data to the stack.
Fixes: ea9b847cda ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Change the division in ice_ptp_adjfine from div_u64 to div64_u64.
div_u64 is used when the divisor is 32 bit but in this case incval is
64 bit and it caused incorrect calculations and incval adjustments.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The watchdog task incorrectly changes the state to __IAVF_RESETTING,
instead of letting the reset task take care of that. This was already
resolved by commit 22c8fd71d3 ("iavf: do not override the adapter
state in the watchdog task") but the problem was reintroduced by the
recent code refactoring in commit 45eebd6299 ("iavf: Refactor iavf
state machine tracking").
Fixes: 45eebd6299 ("iavf: Refactor iavf state machine tracking")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This code was re-organized and there some unlocks missing now.
Fixes: 898ef1cb1c ("iavf: Combine init and watchdog state machines")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-12-08
Yahui adds re-initialization of Flow Director for VF reset.
Paul restores interrupts when enabling VFs.
Dave re-adds bandwidth check for DCBNL and moves DSCP mode check
earlier in the function.
Jesse prevents reporting of dropped packets that occur during
initialization and fixes reporting of statistics which could occur with
frequent reads.
Michal corrects setting of protocol type for UDP header and fixes lack
of differentiation when adding filters for tunnels.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: safer stats processing
ice: fix adding different tunnels
ice: fix choosing UDP header type
ice: ignore dropped packets during init
ice: Fix problems with DSCP QoS implementation
ice: rearm other interrupt cause register after enabling VFs
ice: fix FDIR init missing when reset VF
====================
Link: https://lore.kernel.org/r/20211208211144.2629867-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver was zeroing live stats that could be fetched by
ndo_get_stats64 at any time. This could result in inconsistent
statistics, and the telltale sign was when reading stats frequently from
/proc/net/dev, the stats would go backwards.
Fix by collecting stats into a local, and delaying when we write to the
structure so it's not incremental.
Fixes: fcea6f3da5 ("ice: Add stats and ethtool support")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adding filters with the same values inside for VXLAN and Geneve causes HW
error, because it looks exactly the same. To choose between different
type of tunnels new recipe is needed. Add storing tunnel types in
creating recipes function and start checking it in finding function.
Change getting open tunnels function to return port on correct tunnel
type. This is needed to copy correct port to dummy packet.
Block user from adding enc_dst_port via tc flower, because VXLAN and
Geneve filters can be created only with destination port which was
previously opened.
Fixes: 8b032a55c1 ("ice: low level support for tunnels")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In tunnels packet there can be two UDP headers:
- outer which for hw should be mark as ICE_UDP_OF
- inner which for hw should be mark as ICE_UDP_ILOS or as ICE_TCP_IL if
inner header is of TCP type
In none tunnels packet header can be:
- UDP, which for hw should be mark as ICE_UDP_ILOS
- TCP, which for hw should be mark as ICE_TCP_IL
Change incorrect ICE_UDP_OF for none tunnel packets to ICE_UDP_ILOS.
ICE_UDP_OF is incorrect for none tunnel packets and setting it leads to
error from hw while adding this kind of recipe.
In summary, for tunnel outer port type should always be set to
ICE_UDP_OF, for none tunnel outer and tunnel inner it should always be
set to ICE_UDP_ILOS.
Fixes: 9e300987d4 ("ice: VXLAN and Geneve TC support")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If the hardware is constantly receiving unicast or broadcast packets
during driver load, the device previously counted many GLV_RDPC (VSI
dropped packets) events during init. This causes confusing dropped
packet statistics during driver load. The dropped packets counter
incrementing does stop once the driver finishes loading.
Avoid this problem by baselining our statistics at the end of driver
open instead of the end of probe.
Fixes: cdedef59de ("ice: Configure VSIs for Tx/Rx")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The patch that implemented DSCP QoS implementation removed a
bandwidth check that was used to check for a specific condition
caused by some corner cases. This check should not of been
removed.
The same patch also added a check for when the DCBx state could
be changed in relation to DSCP, but the check was erroneously
added nested in a check for CEE mode, which made the check useless.
Fix these problems by re-adding the bandwidth check and relocating
the DSCP mode check earlier in the function that changes DCBx state
in the driver.
Fixes: 2a87bd73e5 ("ice: Add DSCP support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The other interrupt cause register (OICR), global interrupt 0, is
disabled when enabling VFs to prevent handling VFLR. If the OICR is
not rearmed then the VF cannot communicate with the PF.
Rearm the OICR after enabling VFs.
Fixes: 916c7fdf5e ("ice: Separate VF VSI initialization/creation from reset flow")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When VF is being reset, ice_reset_vf() will be called and FDIR
resource should be released and initialized again.
Fixes: 1f7ea1cd6a ("ice: Enable FDIR Configure for AVF")
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When trying to dump VFs VSI RX/TX descriptors
using debugfs there was a crash
due to NULL pointer dereference in i40e_dbg_dump_desc.
Added a check to i40e_dbg_dump_desc that checks if
VSI type is correct for dumping RX/TX descriptors.
Fixes: 02e9c29081 ("i40e: debugfs interface")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After setting pre-set combined to 16 queues and reserving 16 queues by
tc qdisc, pre-set maximum combined queues returned to default value
after VF reset being 4 and this generated errors during removing tc.
Fixed by removing clear num_req_queues before reset VF.
Fixes: e284fc2804 (i40e: Add and delete cloud filter)
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Bindushree P <Bindushree.p@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix failed operation code appearing if handling messages from VF.
Implemented by waiting for VF appropriate state if request starts
handle while VF reset.
Without this patch the message handling request while VF is in
a reset state ends with error -5 (I40E_ERR_PARAM).
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
iavf_set_ringparams doesn't communicate to the user that
1. The user requested descriptor count is out of range. Instead it
just quietly sets descriptors to the "clamped" value and calls it
done. This makes it look an invalid value was successfully set as
the descriptor count when this isn't actually true.
2. The user provided descriptor count needs to be inflated for alignment
reasons.
This behavior is confusing. The ice driver has already addressed this
by rejecting invalid values for descriptor count and
messaging for alignment adjustments.
Do the same thing here by adding the error and info messages.
Fixes: fbb7ddfef2 ("i40evf: core ethtool functionality")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If the PF experiences an FLR, the VF's MSI and MSI-X configuration will
be conveniently and silently removed in the process. When this happens,
reset recovery will appear to complete normally but no traffic will
pass. The netdev watchdog will helpfully notify everyone of this issue.
To prevent such public embarrassment, restore MSI configuration at every
reset. For normal resets, this will do no harm, but for VF resets
resulting from a PF FLR, this will keep the VF working.
Fixes: 5eae00c57f ("i40evf: main driver core")
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix a bug in which the receiving of packets can stop in the zero-copy
driver. Ice HW ignores 3 lower bits from QRX_TAIL register, which means
that tail is bumped only on intervals of 8. Currently with XSK RX
batching in place, ice_alloc_rx_bufs_zc() clears the status_error0 only
of the last descriptor that has been allocated/taken from the XSK buffer
pool. status_error0 includes DD bit that is looked upon by the
ice_clean_rx_irq_zc() to tell if a descriptor can be processed.
The bug can be triggered when driver updates the ntu but not the
QRX_TAIL, so HW wouldn't have a chance to write to the ready
descriptors. Later on driver moves the ntc to the mentioned set of
descriptors and interprets them as a ready to be processed, since
corresponding DD bits were not cleared nor any writeback has happened
that would clear it. This can then lead to ntc == ntu case which means
that ring is empty and no further packet processing.
Fix the XSK traffic hang that can be observed when l2fwd scenario from
xdpsock is used by making sure that status_error0 is cleared for each
descriptor that is fed to HW and therefore we are sure that driver will
not processed non-valid DD bits. This will also prevent the driver from
processing the descriptors that were allocated in favor of the
previously processed ones, but writeback didn't happen yet.
Fixes: db804cfc21 ("ice: Use the xsk batched rx allocation interface")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksandr brought a bug report where netpoll causes trace
messages in the log on igb.
Danielle brought this back up as still occurring, so we'll try
again.
[22038.710800] ------------[ cut here ]------------
[22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll
[22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0
As Alex suggested, change the driver to return work_done at the
exit of napi_poll, which should be safe to do in this driver
because it is not polling multiple queues in this single napi
context (multiple queues attached to one MSI-X vector). Several
other drivers contain the same simple sequence, so I hope
this will not create new problems.
Fixes: 16eb8815c2 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Danielle Ratson <danieller@nvidia.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a VF goes through a reset, it's possible for the VF's feature set
to change. For example it may lose the VIRTCHNL_VF_OFFLOAD_VLAN
capability after VF reset. Unfortunately, the driver doesn't correctly
deal with this situation and errors are seen from downing/upping the
interface and/or moving the interface in/out of a network namespace.
When setting the interface down/up we see the following errors after the
VIRTCHNL_VF_OFFLOAD_VLAN capability was taken away from the VF:
ice 0000:51:00.1: VF 1 failed opcode 12, retval: -64 iavf 0000:51:09.1:
Failed to add VLAN filter, error IAVF_NOT_SUPPORTED ice 0000:51:00.1: VF
1 failed opcode 13, retval: -64 iavf 0000:51:09.1: Failed to delete VLAN
filter, error IAVF_NOT_SUPPORTED
These add/delete errors are happening because the VLAN filters are
tracked internally to the driver and regardless of the VLAN_ALLOWED()
setting the driver tries to delete/re-add them over virtchnl.
Fix the delete failure by making sure to delete any VLAN filter tracking
in the driver when a removal request is made, while preventing the
virtchnl request. This makes it so the driver's VLAN list is up to date
and the errors are
Fix the add failure by making sure the check for VLAN_ALLOWED() during
reset is done after the VF receives its capability list from the PF via
VIRTCHNL_OP_GET_VF_RESOURCES. If VLAN functionality is not allowed, then
prevent requesting re-adding the filters over virtchnl.
When moving the interface into a network namespace we see the following
errors after the VIRTCHNL_VF_OFFLOAD_VLAN capability was taken away from
the VF:
iavf 0000:51:09.1 enp81s0f1v1: NIC Link is Up Speed is 25 Gbps Full Duplex
iavf 0000:51:09.1 temp_27: renamed from enp81s0f1v1
iavf 0000:51:09.1 mgmt: renamed from temp_27
iavf 0000:51:09.1 dev27: set_features() failed (-22); wanted 0x020190001fd54833, left 0x020190001fd54bb3
These errors are happening because we aren't correctly updating the
netdev capabilities and dealing with ndo_fix_features() and
ndo_set_features() correctly.
Fix this by only reporting errors in the driver's ndo_set_features()
callback when VIRTCHNL_VF_OFFLOAD_VLAN is not allowed and any attempt to
enable the VLAN features is made. Also, make sure to disable VLAN
insertion, filtering, and stripping since the VIRTCHNL_VF_OFFLOAD_VLAN
flag applies to all of them and not just VLAN stripping.
Also, after we process the capabilities in the VF reset path, make sure
to call netdev_update_features() in case the capabilities have changed
in order to update the netdev's feature set to match the VF's actual
capabilities.
Lastly, make sure to always report success on VLAN filter delete when
VIRTCHNL_VF_OFFLOAD_VLAN is not supported. The changed flow in
iavf_del_vlans() allows the stack to delete previosly existing VLAN
filters even if VLAN filtering is not allowed. This makes it so the VLAN
filter list is up to date.
Fixes: 8774370d26 ("i40e/i40evf: support for VF VLAN tag stripping control")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently iavf adapter statistics are refreshed only in a
watchdog task, triggered approximately every two seconds,
which causes some ethtool requests to return outdated values.
Add explicit statistics refresh when requested by ethtool -S.
Fixes: b476b0030e ("iavf: Move commands processing to the separate function")
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
System hangs if close the interface is called from the kernel during
the interface is in resetting state.
During resetting operation the link is closing but kernel didn't
know it and it tried to close this interface again what sometimes
led to deadlock.
Inform kernel about current state of interface
and turn off the flag IFF_UP when interface is closing until reset
is finished.
Previously it was most likely to hang the system when kernel
(network manager) tried to close the interface in the same time
when interface was in resetting state because of deadlock.
Fixes: 3c8e0b989a ("i40vf: don't stop me now")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Resolve being able to change static values on VF when adaptive interrupt
moderation is enabled.
This problem is fixed by checking the interrupt settings is not
a combination of change of static value while adaptive interrupt
moderation is turned on.
Without this fix, the user would be able to change static values
on VF with adaptive moderation enabled.
Fixes: 65e87c0398 ("i40evf: support queue-specific settings for interrupt moderation")
Signed-off-by: Nitesh B Venkatesh <nitesh.b.venkatesh@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-11-17
This series contains updates to i40e driver only.
Eryk adds accounting for VLAN header in packet size when VF port VLAN is
configured. He also fixes TC queue distribution when the user has changed
queue counts as well as for configuration of VF ADQ which caused dropped
packets.
Michal adds tracking for when a VSI is being released to prevent null
pointer dereference when managing filters.
Karen ensures PF successfully initiates VF requested reset which could
cause a call trace otherwise.
Jedrzej moves validation of channel queue value earlier to prevent
partial configuration when the value is invalid.
Grzegorz corrects the reported error when adding filter fails.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported in [1], e100 was no longer working for suspend/resume
cycles. The previous commit mentioned in the fixes appears to have
broken things and this attempts to practice best known methods for
device power management and keep wake-up working while allowing
suspend/resume to work. To do this, I reorder a little bit of code
and fix the resume path to make sure the device is enabled.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=214933
Fixes: 69a74aef8a ("e100: use generic power management")
Cc: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reported-by: Alexey Kuznetsov <axet@me.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Alexey Kuznetsov <axet@me.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix misleading display error in dmesg if tc filter return fail.
Only i40e status error code should be converted to string, not linux
error code. Otherwise, we return false information about the error.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reject TCs creation with proper message if the first queue
assignment is not equal to the power of two.
The first queue number was checked too late in the second queue
iteration, if second queue was configured at all. Now if first queue value
is not a power of two, then trying to create qdisc will be rejected.
Fixes: 8f88b3034d ("i40e: Add infrastructure for queue channel support")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Restore part of reset functionality used when reset is called
from the VF to reset itself. Without this fix warning message
is displayed when VF is being removed via sysfs.
Fix the crash of the VF during reset by ensuring
that the PF receives the reset message successfully.
Refactor code to use one function instead of two.
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Properly reconfigure VF VSIs after VF request ADQ.
Created new function to update queue mapping and queue pairs per TC
with AQ update VSI. This sets proper RSS size on NIC.
VFs num_queue_pairs should not be changed during setup of queue maps.
Previously, VF main VSI in ADQ had configured too many queues and had
wrong RSS size, which lead to packets not being consumed and drops in
connectivity.
Fixes: bc6d33c8d9 ("i40e: Fix the number of queues available to be mapped for use")
Co-developed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the i40e_vsi_setup_queue_map is basing the count of queues in
TCs on a VSI's alloc_queue_pairs member which is not changed throughout
any user's action (for example via ethtool's set_channels callback).
This implies that vsi->tc_config.tc_info[n].qcount value that is given
to the kernel via netdev_set_tc_queue() that notifies about the count of
queues per particular traffic class is constant even if user has changed
the total count of queues.
This in turn caused the kernel warning after setting the queue count to
the lower value than the initial one:
$ ethtool -l ens801f0
Channel parameters for ens801f0:
Pre-set maximums:
RX: 0
TX: 0
Other: 1
Combined: 64
Current hardware settings:
RX: 0
TX: 0
Other: 1
Combined: 64
$ ethtool -L ens801f0 combined 40
[dmesg]
Number of in use tx queues changed invalidating tc mappings. Priority
traffic classification disabled!
Reason was that vsi->alloc_queue_pairs stayed at 64 value which was used
to set the qcount on TC0 (by default only TC0 exists so all of the
existing queues are assigned to TC0). we update the offset/qcount via
netdev_set_tc_queue() back to the old value but then the
netif_set_real_num_tx_queues() is using the vsi->num_queue_pairs as a
value which got set to 40.
Fix it by using vsi->req_queue_pairs as a queue count that will be
distributed across TCs. Do it only for non-zero values, which implies
that user actually requested the new count of queues.
For VSIs other than main, stay with the vsi->alloc_queue_pairs as we
only allow manipulating the queue count on main VSI.
Fixes: bc6d33c8d9 ("i40e: Fix the number of queues available to be mapped for use")
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Co-developed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the reason of null pointer dereference in sync VSI filters.
Added new I40E_VSI_RELEASING flag to signalize deleting and releasing
of VSI resources to sync this thread with sync filters subtask.
Without this patch it is possible to start update the VSI filter list
after VSI is removed, that's causing a kernel oops.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Reviewed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Reviewed-by: Witold Fijalkowski <witoldx.fijalkowski@intel.com>
Reviewed-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Setting VLAN port increasing RX queue max_pkt_size
by 4 bytes to take VLAN tag into account.
Trigger the VF reset when setting port VLAN for
VF to renegotiate its capabilities and reinitialize.
Fixes: ba4e003d29 ("i40e: don't hold spinlock while resetting VF")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Restore VLAN filters after the link is brought down, and up - since all
filters are deleted from HW during the netdev link down routine.
Fixes: ed1f5b58ea ("i40evf: remove VLAN filters on close")
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Now setting combine to 0 will be rejected with the
appropriate error code.
This has been implemented by adding a condition that checks
the value of combine equal to zero.
Without this patch, when the user requested it, no error was
returned and combine was set to the default value for VF.
Fixes: 5520deb153 ("iavf: Enable support for up to 16 queues")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
While issuing VF Reset from the guest OS, the VF driver prints
logs about critical / Overflow error detection. This is not an
actual error since the VF_MBX_ARQLEN register is set to all FF's
for a short period of time and the VF would catch the bits set if
it was reading the register during that spike of time.
This patch introduces an additional check to ignore this condition
since the VF is in reset.
Fixes: 19b73d8efa ("i40evf: Add additional check for reset")
Signed-off-by: Surabhi Boob <surabhi.boob@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In some cases, the ethtool get_rxfh handler may be called with a null
key or indir parameter. So check these pointers, or you will have a very
bad day.
Fixes: 43a3d9ba34 ("i40evf: Allow PF driver to configure RSS")
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In iavf_config_clsflower, the filter structure could be accidentally
released at the end, if iavf_parse_cls_flower or iavf_handle_tclass ever
return a non-zero but positive value.
In this case, the function continues through to the end, and will call
kfree() on the filter structure even though it has been added to the
linked list.
This can actually happen because iavf_parse_cls_flower will return
a positive IAVF_ERR_CONFIG value instead of the traditional negative
error codes.
Fix this by ensuring that the kfree() check and error checks are
similar. Use the more idiomatic "if (err)" to catch all non-zero error
codes.
Fixes: 0075fa0fad ("i40evf: Add support to apply cloud filters")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver could only quit allmulti when allmulti and promisc modes are
turn on at the same time. If promisc had been off there was no way to turn
off allmulti mode.
The patch corrects this behavior. Switching allmulti does not depends on
promisc state mode anymore
Fixes: f42a5c74da ("i40e: Add allmulti support for the VF")
Signed-off-by: Piotr Marczak <piotr.marczak@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In iavf_configure_clsflower() the function will bail out if it is unable
to obtain the crit_section lock in a reasonable time. However, it will
clear the lock when exiting, so fix this.
Fixes: 640a8af584 ("i40evf: Reorder configure_clsflower to avoid deadlock on error")
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
