According to:
https://github.com/intel/ipu6-drivers/blob/master/patch/int3472-support-independent-clock-and-LED-gpios-5.17%2B.patch
Bits 31-24 of the _DSM pin entry integer value codes the active-value,
that is the actual physical signal (0 or 1) which needs to be output on
the pin to turn the sensor chip on (to make it active).
So if bits 31-24 are 0 for a reset pin, then the actual value of the reset
pin needs to be 0 to take the chip out of reset. IOW in this case the reset
signal is active-high rather then the default active-low.
And if bits 31-24 are 0 for a clk-en pin then the actual value of the clk
pin needs to be 0 to enable the clk. So in this case the clk-en signal
is active-low rather then the default active-high.
IOW if bits 31-24 are 0 for a pin, then the default polarity of the pin
is inverted.
Add a check for this and also propagate this new polarity to the clock
registration.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20230127203729.10205-6-hdegoede@redhat.com
Move the requesting of the clk-enable GPIO to skl_int3472_register_clock()
(and move the gpiod_put to unregister).
This mirrors the GPIO handling in skl_int3472_register_regulator() and
allows removing skl_int3472_map_gpio_to_clk() from discrete.c.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20230127203729.10205-5-hdegoede@redhat.com
On some systems, e.g. the Lenovo ThinkPad X1 Yoga gen 7 and the ThinkPad
X1 Nano gen 2 there is no clock-enable pin, triggering the:
"No clk GPIO. The privacy LED won't work" warning and causing the privacy
LED to not work.
Fix this by modeling the privacy LED as a LED class device rather then
integrating it with the registered clock.
Note this relies on media subsys changes to actually turn the LED on/off
when the sensor's v4l2_subdev's s_stream() operand gets called.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20230127203729.10205-4-hdegoede@redhat.com
Add a helper function to map the type returned by the _DSM
method to a function name + the default polarity for that function.
And fold the INT3472_GPIO_TYPE_RESET and INT3472_GPIO_TYPE_POWERDOWN
cases into a single generic case.
This is a preparation patch for further GPIO mapping changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20230127203729.10205-3-hdegoede@redhat.com
acpi_get_and_request_gpiod() does not take a gpio_lookup_flags argument
specifying that the pins direction should be initialized to a specific
value.
This means that in some cases the pins might be left in input mode, causing
the gpiod_set() calls made to enable the clk / regulator to not work.
One example of this problem is the clk-enable GPIO for the ov01a1s sensor
on a Dell Latitude 9420 being left in input mode causing the clk to
never get enabled.
Explicitly set the direction of the pins to output to fix this.
Fixes: 5de691bffe ("platform/x86: Add intel_skl_int3472 driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <djrscally@gmail.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20230111201426.947853-1-hdegoede@redhat.com
By swapping the definition of skl_int3472_discrete_remove() and
skl_int3472_discrete_probe() the forward declaration of the former can
be dropped. This is a good thing as it removes code duplication.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Daniel Scally <djrscally@gmail.com>
Link: https://lore.kernel.org/r/20220920070101.907596-1-u.kleine-koenig@pengutronix.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Replace acpi_bus_get_device() that is going to be dropped with
acpi_fetch_acpi_dev().
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/2631712.mvXUDI8C0e@kreacher
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The clk and regulator frameworks expect clk/regulator consumer-devices
to have info about the consumed clks/regulators described in the device's
fw_node.
To work around this info missing from the ACPI tables on devices where
the int3472 driver is used, the int3472 MFD-cell drivers attach info about
consumers to the clks/regulators when registering these.
This causes problems with the probe ordering wrt drivers for consumers
of these clks/regulators. Since the lookups are only registered when the
provider-driver binds, trying to get these clks/regulators before then
results in a -ENOENT error for clks and a dummy regulator for regulators.
All the sensor ACPI fw-nodes have a _DEP dependency on the INT3472 ACPI
fw-node, so to work around these probe ordering issues the ACPI core /
i2c-code does not instantiate the I2C-clients for any ACPI devices
which have a _DEP dependency on an INT3472 ACPI device until all
_DEP-s are met.
This relies on acpi_dev_clear_dependencies() getting called by the driver
for the _DEP-s when they are ready, add a acpi_dev_clear_dependencies()
call to the discrete.c probe code.
In the tps68470 case calling acpi_dev_clear_dependencies() is already done
by the acpi_gpiochip_add() call done by the driver for the GPIO MFD cell
(The GPIO cell is deliberately the last cell created to make sure the
clk + regulator cells are already instantiated when this happens).
However for proper probe ordering, the clk/regulator cells must not just
be instantiated the must be fully ready (the clks + regulators must be
registered with their subsystems).
Add MODULE_SOFTDEP dependencies for the clk and regulator drivers for
the instantiated MFD-cells so that these are loaded before us and so
that they bind immediately when the platform-devs are instantiated.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-12-hdegoede@redhat.com
The discrete.c code is not the only code which needs to lookup the
acpi_device and device-name for the sensor for which the INT3472
ACPI-device is a GPIO/clk/regulator provider.
The tps68470.c code also needs this functionality, so factor this
out into a new get_sensor_adev_and_name() helper.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-9-hdegoede@redhat.com
The intel_skl_int3472.ko module contains 2 separate drivers,
the int3472_discrete platform driver and the int3472_tps68470
I2C-driver.
These 2 drivers contain very little shared code, only
skl_int3472_get_acpi_buffer() and skl_int3472_fill_cldb() are
shared.
Split the module into 2 drivers, linking the little shared code
directly into both.
This will allow us to add soft-module dependencies for the
tps68470 clk, gpio and regulator drivers to the new
intel_skl_int3472_tps68470.ko to help with probe ordering issues
without causing these modules to get loaded on boards which only
use the int3472_discrete platform driver.
While at it also rename the .c and .h files to remove the
cumbersome intel_skl_int3472_ prefix.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-8-hdegoede@redhat.com
2021-12-13 11:44:48 +01:00
Renamed from drivers/platform/x86/intel/int3472/intel_skl_int3472_discrete.c (Browse further)
