Update GC golden setting for navy_flounder.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's the same with sienna_cichlid, cp fw for navy_flounder
can support WAIT_REG_MEM packet.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add gc golden setting for navy_flounder
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pa_sc_tile_steering_override is only programmable for
gfx10.0/10.1/10.2, and navy_flounder has the same gfx10.3 IP
with sienna_cichlid.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The gfx version of navy_flounder is 10.3, identical to
sienna_cichlid, follow the way of sienna_cichlid.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Jiansong Chen <Jiansong.Chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
since navy_flounder has similar gc IP version with
sienna_cichlid, follow its setting for the moment.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <Tao.Zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Same as navi10.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For gfx10 boards, except for nv12, other boards take mmio write
rather than rlcg write
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During preemption test for gfx10, it uses kiq to trigger
gfx preemption, which would result in race condition
with flushing TLB for kiq.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove some unused ASIC check logic.
Remove some definition of amdgpu_device which only used by
the removed ASIC check logic.(V2)
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use RREG32_KIQ to read gfx register when try to get gfx/sdma
clockgating state instead of RREG32, as it will result
to system hard hang when GPU is enter into GFXOFF state.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The KFD VMID assignment was hard-coded in a few places. Consolidate that in
a single variable adev->vm_manager.first_kfd_vmid. The value is still
assigned in gmc-ip-version-specific code.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As will clear vf fw during unload driver, to avoid idle fail. Need
to clear KIQ portion also.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Ack-by: Monk.liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only enable one gfx pipe for sienna_cichlid currently.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On SRIOV run time, driver shouldn't directly access invalidation registers through MMIO.
Use kiq to submit wait_reg_mem package for the invalidation
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only disable 3D pipe 1 on navi1x, enable 3D pipe 1 on Sienna_Cichlid.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update gfx golden setting for gfx10.3.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
tiling mode table is not used anymore for gfx10
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pa_sc_tile_steering_override is only programmable for
gfx10.0/10.1/10.2
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The number of queue per pipe for mec on sienna_cichlid should be 4.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update sienna_cichlid register configuration for sienna_cichlid
to match the update of header files.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Same as navi10.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For SRIOV, since the CP_INT_CNTL_RING0 is programed on host side.
The Guest should not program CP_INT_CNTL_RING0 again.
Signed-off-by: Gavin Wan <Gavin.Wan@amd.com>
Reviewed-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Compute IBs need this too.
v2: split out version bump
v3: squash in emit frame count fixes
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is no need to use amdgpu_mm_wreg_mmio_rlc()
during initialization time because this interface
is only designed for debugfs case to access the
registers which are only permitted by RLCG during
run-time. Therefore, turn back rlcg write for gfx_v10.
If we not turn back it, it will raise amdgpu load failure.
[ 54.904333] amdgpu: SMU driver if version not matched
[ 54.904393] amdgpu: SMU is initialized successfully!
[ 54.905971] [drm] kiq ring mec 2 pipe 1 q 0
[ 55.115416] amdgpu 0000:00:06.0: [drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring gfx_0.0.0 test failed (-110)
[ 55.118877] [drm:amdgpu_device_init [amdgpu]] *ERROR* hw_init of IP block <gfx_v10_0> failed -110
[ 55.126587] amdgpu 0000:00:06.0: amdgpu_device_ip_init failed
[ 55.133466] amdgpu 0000:00:06.0: Fatal error during GPU init
Signed-off-by: Yintian Tao <yttao@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Same as gfx9. This allows us to kill the waves for hung
shaders.
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As this is already properly handled in amdgpu_gfx_off_ctrl(). In fact,
this unnecessary cancel_delayed_work_sync may leave a small time window
for race condition and is dangerous.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise, MGCG/MGLS will be left enabled.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Create gfx_v10_0_rlc_funcs_sriov for nv12 with rlcg_write function pointers be initialized
so driver can use RLCG to write aceess CSIB and CP_ME_CNTL registers when nv12 in sriov mode
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since commit "Move to a per-IB secure flag (TMZ)",
we've been seeing hangs in GFX. We need to send
FRAME CONTROL stop/start back-to-back, every time
we flip the TMZ flag. That is, when we transition
from TMZ to non-TMZ we have to send a stop with
TMZ followed by a start with non-TMZ, and
similarly for transitioning from non-TMZ into TMZ.
This patch implements this, thus fixing the GFX
hang.
v1 -> v2:
As suggested by Luben, and accept part of implemetation from this patch:
- Put "secure" closed to the loop and use optimization
- Change "secure" to bool again, and move "secure == -1" out of loop.
v3: Small fixes/optimizations.
Reported-and-Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move from a per-CS secure flag (TMZ) to a per-IB
secure flag.
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement an accessor of adev->tmz.enabled. Let not
code around access it as "if (adev->tmz.enabled)"
as the organization may change. Instead...
Recruit "bool amdgpu_is_tmz(adev)" to return
exactly this Boolean value. That is, this function
is now an accessor of an already initialized and
set adev and adev->tmz.
Add "void amdgpu_gmc_tmz_set(adev)" to check and
set adev->gmc.tmz_enabled at initialization
time. After which one uses "bool
amdgpu_is_tmz(adev)" to query whether adev
supports TMZ.
Also, remove circular header file include.
v2: Remove amdgpu_tmz.[ch] as requested.
v3: Move TMZ into GMC.
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch enables TMZ bit in FRAME_CONTROL for gfx10.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch expands the context control function to support trusted flag while we
want to set command buffer in trusted mode.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch expands the emit_tmz function to support trusted flag while we want
to set command buffer in trusted mode.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
