Use eth_zero_addr() to clear mac address instead of memset().
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace memsets of 1 byte with simple assignment.
Issue found with checkpatch.pl
Signed-off-by: Suraj Upadhyay <usuraj35@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We observed two panics involving races with igb_reset_task.
The first panic is caused by this race condition:
kworker reboot -f
igb_reset_task
igb_reinit_locked
igb_down
napi_synchronize
__igb_shutdown
igb_clear_interrupt_scheme
igb_free_q_vectors
igb_free_q_vector
adapter->q_vector[v_idx] = NULL;
napi_disable
Panics trying to access
adapter->q_vector[v_idx].napi_state
The second panic (a divide error) is caused by this race:
kworker reboot -f tx packet
igb_reset_task
__igb_shutdown
rtnl_lock()
...
igb_clear_interrupt_scheme
igb_free_q_vectors
adapter->num_tx_queues = 0
...
rtnl_unlock()
rtnl_lock()
igb_reinit_locked
igb_down
igb_up
netif_tx_start_all_queues
dev_hard_start_xmit
igb_xmit_frame
igb_tx_queue_mapping
Panics on
r_idx % adapter->num_tx_queues
This commit applies to igb_reset_task the same changes that
were applied to ixgbe in commit 2f90b8657e ("ixgbe: this patch
adds support for DCB to the kernel and ixgbe driver"),
commit 8f4c5c9fb8 ("ixgbe: reinit_locked() should be called with
rtnl_lock") and commit 88adce4ea8 ("ixgbe: fix possible race in
reset subtask").
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Convert all the remaining 'fall through" code comments to the newer
'fallthrough;' keyword.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.
For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running. So we now pass the
value of UTS_RELEASE to the firmware. This adminq call is required per
the HAS document. The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.
What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
This function always return 0 now, we can make it return void to
simplify the code. This fixes the following coccicheck warning:
drivers/net/ethernet/intel/igb/e1000_mac.c:728:5-12: Unneeded variable:
"ret_val". Return "0" on line 751
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igb device gets runtime suspended when there's no link partner. We can't
get correct speed under that state:
$ cat /sys/class/net/enp3s0/speed
1000
In addition to that, an error can also be spotted in dmesg:
[ 385.991957] igb 0000:03:00.0 enp3s0: PCIe link lost
Since device can only be runtime suspended when there's no link partner,
we can skip reading register and let the following logic set speed and
duplex with correct status.
The more generic approach will be wrap get_link_ksettings() with begin()
and complete() callbacks. However, for this particular issue, begin()
calls igb_runtime_resume() , which tries to rtnl_lock() while the lock
is already hold by upper ethtool layer.
So let's take this approach until the igb_runtime_resume() no longer
needs to hold rtnl_lock.
CC: stable <stable@vger.kernel.org>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename DPM_FLAG_NEVER_SKIP to DPM_FLAG_NO_DIRECT_COMPLETE which
matches its purpose more closely.
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # for PCI parts
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver was rejecting almost all unsupported
parameters already, it was only missing a check
for tx_max_coalesced_frames_irq.
As a side effect of these changes the error code for
unsupported params changes from ENOTSUPP to EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the link mode should also be done for 100BaseFX SGMII modules,
otherwise they just don't work when the default link mode in CTRL_EXT
coming from the EEPROM is SERDES.
Additionally 100Base-LX SGMII SFP modules are also supported now, which
was not the case before.
Tested with an i210 using Flexoptix S.1303.2M.G 100FX and
S.1303.10.G 100LX SGMII SFP modules.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If Rx flow control has been enabled (via autoneg or forced), packets
should not be dropped due to Rx descriptor ring exhaustion. Instead
pause frames should be used to apply back pressure. This only applies
if VFs are not in use.
Move SRRCTL setup to its own function for easy reuse and only set drop
enable bit if Rx flow control is not enabled.
Since v1: always enable dropping of packets if VFs in use.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
This hardware always time stamps rising and falling edges, and so this
patch validates that the request does contains both edges.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User space may request time stamps on rising edges, falling edges, or
both. However, the particular mode may or may not be supported in the
hardware or in the driver. This patch adds a "strict" flag that tells
drivers to ensure that the requested mode will be honored.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the igb PTP support to explicitly reject any future flags that
get added to the external timestamp request ioctl.
In order to maintain currently functioning code, this patch accepts all
three current flags. This is because the PTP_RISING_EDGE and
PTP_FALLING_EDGE flags have unclear semantics and each driver seems to
have interpreted them slightly differently.
This HW always time stamps both edges:
flags Meaning
---------------------------------------------------- --------------------------
PTP_ENABLE_FEATURE Time stamp both edges
PTP_ENABLE_FEATURE|PTP_RISING_EDGE Time stamp both edges
PTP_ENABLE_FEATURE|PTP_FALLING_EDGE Time stamp both edges
PTP_ENABLE_FEATURE|PTP_RISING_EDGE|PTP_FALLING_EDGE Time stamp both edges
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 823eb2a3c4 ("PTP: add support for one-shot output") introduced
a new flag for the PTP periodic output request ioctl. This flag is not
currently supported by any driver.
Fix all drivers which implement the periodic output request ioctl to
explicitly reject any request with flags they do not understand. This
ensures that the driver does not accidentally misinterpret the
PTP_PEROUT_ONE_SHOT flag, or any new flag introduced in the future.
This is important for forward compatibility: if a new flag is
introduced, the driver should reject requests to enable the flag until
the driver has actually been modified to support the flag in question.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Christopher Hall <christopher.s.hall@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.
Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.
Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.
This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changing a network device MTU can be a fairly frequent operation, and
failure to change the MTU is reflected to user-space properly, both by
an appropriate message as well as by looking at whether the device's MTU
matches the configuration.
Demote the prints to debug prints by using netdev_dbg(), making all
Intel wired LAN drivers consistent, since they used a mixture of PCI
device and network device prints before.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on the i350 there is an annoying behavior that is maybe also
present on 82580 devices, but was probably not noticed yet as MAS is not
widely used.
If no cable is connected on both fiber/copper ports the media auto sense
code will constantly swap between them as part of the watchdog task and
produce many unnecessary kernel log messages.
The swap code responsible for this behavior (switching to fiber) should
not be executed if the current media type is copper and there is no signal
detected on the fiber port. In this case we can safely wait until the
AUTOSENSE_EN bit is cleared.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables the hardware feature "Media Auto Sense" also on the
i350. It works in the same way as on the 82850 devices. Hardware designs
using dual PHYs (fiber/copper) can enable this feature by setting the MAS
enable bits in the NVM_COMPAT register (0x03) in the EEPROM.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on a series from Alexander Duyck this change adds UDP segmentation
offload support to the igb driver.
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Josh Hunt <johunt@akamai.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
And any other existing fields in this structure that refer to tc.
Specifically:
* tc_cls_flower_offload_flow_rule() to flow_cls_offload_flow_rule().
* TC_CLSFLOWER_* to FLOW_CLS_*.
* tc_cls_common_offload to tc_cls_common_offload.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.
This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.
Remove tc_block_offload alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most drivers do the same thing to set up the flow block callbacks, this
patch adds a helper function to do this.
This preparation patch reduces the number of changes to adapt the
existing drivers to use the flow block callback API.
This new helper function takes a flow block list per-driver, which is
set to NULL until this driver list is used.
This patch also introduces the flow_block_command and
flow_block_binder_type enumerations, which are renamed to use
FLOW_BLOCK_* in follow up patches.
There are three definitions (aliases) in order to reduce the number of
updates in this patch, which go away once drivers are fully adapted to
use this flow block API.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-06-28
This series contains a smorgasbord of updates to many of the Intel
drivers.
Gustavo A. R. Silva updates the ice and iavf drivers to use the
strcut_size() helper where possible.
Miguel increases the pause and refresh time for flow control in the
e1000e driver during reset for certain devices.
Dann Frazier fixes a potential NULL pointer dereference in ixgbe driver
when using non-IPSec enabled devices.
Colin Ian King fixes a potential overflow during a shift in the ixgbe
driver. Also fixes a potential NULL pointer dereference in the iavf
driver by adding a check.
Venkatesh Srinivas converts the e1000 driver to use dma_wmb() instead of
wmb() for doorbell writes to avoid SFENCEs in the transmit and receive
paths.
Arjan updates the e1000e driver to improve boot time by over 100 msec by
reducing the usleep ranges suring system startup.
Artem updates the igb driver register dump in ethtool, first prepares
the register dump for future additions of registers in the dump, then
secondly, adds the RR2DCDELAY register to the dump. When dealing with
time-sensitive networks, this register is helpful in determining your
latency from the device to the ring.
Alex fixes the ixgbevf driver to use the current cached link state,
rather than trying to re-check the value from the PF.
Harshitha adds support for MACVLAN offloads in i40e by using channels as
MACVLAN interfaces.
Detlev Casanova updates the e1000e driver to use delayed work instead of
timers to run the watchdog.
Vitaly fixes an issue in e1000e, where when disconnecting and
reconnecting the physical cable connection, the NIC enters a DMoff
state. This state causes a mismatch in link and duplexing, so check the
PCIm function state and perform a PHY reset when in this state to
resolve the issue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the RR2DCDELAY register to the ethtool registers dump.
RR2DCDELAY exists on I210 and I211 Intel Gigabit Ethernet chips and it stands
for "Read Request To Data Completion Delay". Here is how this register is
described in the I210 datasheet:
"This field captures the maximum PCIe split time in 16 ns units, which is the
maximum delay between the read request to the first data completion. This is
giving an estimation of the PCIe round trip time."
In other words, whenever I210 reads from the host memory (e.g., fetches a
descriptor from the ring), the chip measures every PCI DMA read transaction and
captures the maximum value. So it ends up containing the longest DMA
transaction time.
This register is very useful for troubleshooting and research purposes. If you
are dealing with time-sensitive networks, this register can help you get
an idea of your "I210-to-ring" latency. This helps answering questions like
"should I have PCIe ASPM enabled?" or "should I enable deep C-states?" on
my system.
It is safe to read this register at any point, reading it has no effect on
the I210 chip functionality.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch has no functional impact and it is just a preparation
for the following patch. It removes an early return from the
'igb_get_regs()' function by moving the 82576-only registers
dump into an "if" block. With this preparation, we can dump more
non-82576 registers at the end of this function.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a packet which is utilizing the launchtime feature (via SO_TXTIME socket
option) also requests the hardware transmit timestamp, the hardware
timestamp is not delivered to the userspace. This is because the value in
skb->tstamp is mistaken as the software timestamp.
Applications, like ptp4l, request a hardware timestamp by setting the
SOF_TIMESTAMPING_TX_HARDWARE socket option. Whenever a new timestamp is
detected by the driver (this work is done in igb_ptp_tx_work() which calls
igb_ptp_tx_hwtstamps() in igb_ptp.c[1]), it will queue the timestamp in the
ERR_QUEUE for the userspace to read. When the userspace is ready, it will
issue a recvmsg() call to collect this timestamp. The problem is in this
recvmsg() call. If the skb->tstamp is not cleared out, it will be
interpreted as a software timestamp and the hardware tx timestamp will not
be successfully sent to the userspace. Look at skb_is_swtx_tstamp() and the
callee function __sock_recv_timestamp() in net/socket.c for more details.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/intel/igb/e1000_82575.c: In function ‘igb_get_invariants_82575’:
drivers/net/ethernet/intel/igb/e1000_82575.c:636:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (igb_sgmii_uses_mdio_82575(hw)) {
^
drivers/net/ethernet/intel/igb/e1000_82575.c:642:2: note: here
case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/intel/igb/igb_main.c: In function ‘__igb_notify_dca’:
drivers/net/ethernet/intel/igb/igb_main.c:6694:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (dca_add_requester(dev) == 0) {
^
drivers/net/ethernet/intel/igb/igb_main.c:6701:2: note: here
case DCA_PROVIDER_REMOVE:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Failed in read the HW register is very serious for igb/igc driver,
as its hw_addr will be set to NULL and cause the adapter be seen as
"REMOVED".
We saw the error only a few times in the MTBF test for suspend/resume,
but can hardly get any useful info to debug.
Adding WARN() so that we can get the necessary information about
where and how it happens, and use it for root causing and fixing
this "PCIe link lost issue"
This affects igb, igc.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFaUACgkQt6xw3ITB
YzRICQgAiv7wF/yIbBhDOmCNCAKDO59chvFQWxXWdGk/aAB56kwKAMXJgLOvlMG/
VRuuLyParTFQETC3jaxKgnO/1hb+PZLDt2Q2KqixtjIzBypKUPWvK2sf6THhSRF1
GK0DBVUd1rCrWrR815+SPb8el4xXtdBzvAVB+Fx35PXVNpdRdqCkK+EQ6UnXGokm
rXXHbnfsnquBDtmb4CR4r2beH+aNElXbdt0Kj8VcE5J7f7jTdW3z6Q9WFRvdKmK7
yrsxXXB2w/EsWXOwFp0SLTV5+fgeGgTvv8uLjDw+SG6t0E0PebxjNAflT7dPrbYL
WecjKC9WqBxrGY+4ew6YJP70ijLBCw==
=aC8m
-----END PGP SIGNATURE-----
Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
Update all users of eth_get_headlen to pass network device, fetch
network namespace from it and pass it down to the flow dissector.
This commit is a noop until administrator inserts BPF flow dissector
program.
Cc: Maxim Krasnyansky <maxk@qti.qualcomm.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
