Add register writes to enable powering up Type-C subsystem i.e. TCSS.
For MeteorLake we need to request TCSS to power up and check the TCSS
power state after 500 us.
In addition, for PICA we need to set/clear the Type-C PHY ownnership
bit when Type-C device is connected/disconnected.
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-11-mika.kahola@intel.com
As we already do with C10 chip, let's dump the pll
hw state for C20 as well.
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-4-mika.kahola@intel.com
Create a table for C20 DP1.4, DP2.0 and HDMI2.1 rates.
The PLL settings are based on table, not for algorithmic alternative.
For DP 1.4 only MPLLB is in use.
Once register settings are done, we read back C20 HW state.
BSpec: 64568
v2: Updated pll tables (RK)
MPLLB selection fix (RK)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-3-mika.kahola@intel.com
Like DG2, we still don't have a proper algorithm that can be used
for calculating PHY settings, but we do have tables of register
values for a handful of the more common link rates. Some support is
better than none, so let's go ahead and add/use these tables when we
can, and also add some logic to hdmi_port_clock_valid() to filter the
modelist to just the modes we can actually support with these link
rates.
Hopefully we'll have a proper / non-encumbered algorithm to calculate
these registers by the time we upstream and we'll be able to replace
this patch with something more general purpose.
Bspec: 64568
v2: Rebasing with Clint's HDMI C10 PLL tables (Mika)
v3: Remove the extra hdmi clock check pruning.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-8-radhakrishna.sripada@intel.com
C10 phys uses direct mapping internally for voltage and pre-emphasis levels.
Program the levels directly to the fields in the VDR Registers.
Bspec: 65449
v2: From table "C10: Tx EQ settings for DP 1.4x" it shows level 1
and preemphasis 1 instead of two times of level 1 preemphasis 0.
Fix this in the driver code as well.
v3: VSwing update (Clint)
v4: Add vboost termination ctl programming(Imre)
Fix tx llogic and other nits
Restrict C10 vdr ctl register access for C10 phy(RK)
v5: Program vboots, termination ctl for both lanes(Imre)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>(v3)
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-5-radhakrishna.sripada@intel.com
XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy
has a dedicated PIPE 5.2 Message bus for configuration. This message
bus is used to configure the phy internal registers.
XELPDP has C10 phys to drive output to the EDP and the native output
from the display engine. Add structures, programming hardware state
readout logic. Port clock calculations are similar to DG2. Use the DG2
formulae to calculate the port clock but use the relevant pll signals.
Note: PHY lane 0 is always used for PLL programming.
Add sequences for C10 phy enable/disable phy lane reset,
powerdown change sequence and phy lane programming.
Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636
v2: Squash patches related to C10 phy message bus and pll
programming support (Jani)
Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani)
Move macro definitions (Jani)
DP rates as separate patch (Jani)
Spin out xelpdp register definitions into a separate file (Jani)
Replace macro to select registers based on phy lane with
function calls (Jani)
Fix styling issues (Jani)
Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas)
v3: Move clear request flag into try-loop
v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani)
use __intel_de_wait_for_register() instead of __intel_wait_for_register
and uncomment intel_uncore.h (Jani)
Add DP-alt support for PHY lane programming (Khaled)
v4: Add tx and cmn on c10mpllb_state (Imre)
Add missing waits for pending transactions between two message bus
writes (Imre)
General cleanups and simplifications (Imre)
v5: Few nit cleanups from rev4 (imre)
s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK)
Rebase
v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function
Fix typo in comment for REG_FIELD_PREP8 definition(Imre)
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v4)
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
