Make sure that the CRTC state is reset correctly, as expected after
disabling the CRTC.
In particular this change will:
- Zero all the CSC blob pointers after intel_crtc_free_hw_state()
has freed them.
- Zero the shared DPLL and port PLL pointers and clear the
corresponding CRTC reference flag in the PLL state.
- Reset all the transcoder and pipe fields.
v2:
- Reset fully the CRTC state. (Ville)
- Clear pipe active flags in the DPLL state.
v3:
- Clear only the CRTC reference flag and add a helper for this.
(Ville)
v4:
- Rebased on previous patch, adding
intel_unreference_shared_dpll_crtc() separately. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-4-imre.deak@intel.com
Add helpers to reference/unreference a shared DPLL tracking the use of
it by a given CRTC.
This prepares for the next patch, which unreferences a DPLL during CRTC
HW-readout/sanitization.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-3-imre.deak@intel.com
Add i915 parameter to I915_STATE_WARN() and use device based logging.
Done using cocci + hand edited where there was no i915 local variable
ready.
v2: avoid null deref in verify_connector_state()
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512181658.1735594-1-jani.nikula@intel.com
XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy
has a dedicated PIPE 5.2 Message bus for configuration. This message
bus is used to configure the phy internal registers.
XELPDP has C10 phys to drive output to the EDP and the native output
from the display engine. Add structures, programming hardware state
readout logic. Port clock calculations are similar to DG2. Use the DG2
formulae to calculate the port clock but use the relevant pll signals.
Note: PHY lane 0 is always used for PLL programming.
Add sequences for C10 phy enable/disable phy lane reset,
powerdown change sequence and phy lane programming.
Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636
v2: Squash patches related to C10 phy message bus and pll
programming support (Jani)
Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani)
Move macro definitions (Jani)
DP rates as separate patch (Jani)
Spin out xelpdp register definitions into a separate file (Jani)
Replace macro to select registers based on phy lane with
function calls (Jani)
Fix styling issues (Jani)
Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas)
v3: Move clear request flag into try-loop
v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani)
use __intel_de_wait_for_register() instead of __intel_wait_for_register
and uncomment intel_uncore.h (Jani)
Add DP-alt support for PHY lane programming (Khaled)
v4: Add tx and cmn on c10mpllb_state (Imre)
Add missing waits for pending transactions between two message bus
writes (Imre)
General cleanups and simplifications (Imre)
v5: Few nit cleanups from rev4 (imre)
s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK)
Rebase
v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function
Fix typo in comment for REG_FIELD_PREP8 definition(Imre)
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v4)
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
The HTI or HDPORT handling is sprinkled around. Centralize to one place.
Add a note about how subtle the mapping from HDPORT_STATE register to
dpll mask actually is.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221109144209.3624739-1-jani.nikula@intel.com
Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.
Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.
Also some places actually needed i915_irq.h too.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com
Not all Dekel PHY registers have a lane instance, so having to specify
this when using them is awkward. It makes more sense to define each PHY
register with its full internal PHY offset where bits 15:12 is the lane
for lane-instanced PHY registers and just a register bank index for other
PHY registers. This way lane-instanced registers can be referred to with
the (tc_port, lane) parameters, while other registers just with a tc_port
parameter.
An additional benefit of this change is to prevent passing a Dekel
register to a generic MMIO access function or vice versa.
v2:
- Fix parameter reuse in the DKL_REG_MMIO definition.
v3:
- Rebase on latest patchset version.
Cc: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221025114457.2191004-3-imre.deak@intel.com
Move the TypeC DKL PHY register definitions to intel_dkl_phy_regs.h.
No functional changes.
v2:
- Move the definitions to a new intel_dkl_phy_regs.h file. (Jani).
v3:
- Rebase on latest patchset version.
Cc: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221025114457.2191004-2-imre.deak@intel.com
An upcoming patch moves the DKL PHY register definitions to
intel_dkl_phy_regs.h, so for consistency rename intel_tc_phy_regs.h
containing only MG PHY register definitions to intel_mg_phy_regs.h.
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221025102644.2123988-3-imre.deak@intel.com
Accessing the TypeC DKL PHY registers during modeset-commit,
-verification, DP link-retraining and AUX power well toggling is racy
due to these code paths being concurrent and the PHY register bank
selection register (HIP_INDEX_REG) being shared between PHY instances
(aka TC ports) and the bank selection being not atomic wrt. the actual
PHY register access.
Add the required locking around each PHY register bank selection->
register access sequence.
Kudos to Ville for noticing the race conditions.
v2:
- Add the DKL PHY register accessors to intel_dkl_phy.[ch]. (Jani)
- Make the DKL_REG_TC_PORT macro independent of PHY internals.
- Move initing the DKL PHY lock to a more logical place.
v3:
- Fix parameter reuse in the DKL_REG_TC_PORT definition.
- Document the usage of phy_lock.
v4:
- Fix adding TC_PORT_1 offset in the DKL_REG_TC_PORT definition.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v5.5+
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221025114457.2191004-1-imre.deak@intel.com
We currently have a debug message in intel_reference_shared_dpll()
but no counterpart in intel_unreference_shared_dpll(). Add one.
Switch to the [CRTC:...] notation for the pipe name while at it.
v2: Use drm_dbg_kms() instead of drm_dbg() (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922191350.4303-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
To make the fastboot checks at least somewhat sensible let's mark
the expected DPLL as the active one right after we finished the
state computation. Otherwise intel_pipe_config_compare() will
always be comparing things against NULL/0.
TODO: This is still not really right. If the previous commit
had to fall back to the other PLL then the comparisong will
now fail. I guess intel_pipe_config_compare() should rather
be comparing port_dplls[] instead. But to do that we really
should just unify every platform to use the port_dplls[]
approach whether they have any need for PLL fallbacks or not.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-12-ville.syrjala@linux.intel.com
Fill port_clock and hw.adjusted_mode.crtc_clock with the actual
frequency we're going to be getting from the hardware. This will
let us accurately compute all derived state that depends on those.
v2: Reintroduce iCLKIP WARN
v3: Try to deal with VLV/BXT DSI PLL as well
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-8-ville.syrjala@linux.intel.com
This function is supposed to return zero or negative error codes but it
accidentally returns true on failure.
Fixes: 92a020747d ("drm/i915: Split shared dpll .get_dplls() into compute and get phases")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YrVcHArNMTGCSy+9@kili
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The debugs in lower level DPLL code don't really provide any
useful extra information AFAICS. Better just streamline the
code and just put the necessary debugs (to identify at which
step the modeset failed) into the higher level code. In
addition we'll get the full state dump as well, which should
hopefully have enough information to figure out what went wrong.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220503182242.18797-4-ville.syrjala@linux.intel.com
Split the DPLL state computation into a separate function
from the current .get_dplls() which currently serves a dual duty
by also reserving the shared DPLLs.
v2: s/false/-EINVAL/ (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220503182242.18797-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
All .crtc_compute_clock() implementations do the same memset() to
clear the dpll_hw_state (since we preserve it across
intel_crtc_prepare_cleared_state()). Move the memset() to the common
wrapper.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220325123205.22140-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Toss a bunch if constants into .rodata drom the stack. Also
shrink the types of some of the arrays to reduce the size.
bloat-o-meter -c intel_dpll_mgr.o:
add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-86 (-86)
Function old new delta
icl_get_dplls 3393 3372 -21
skl_get_dpll 2069 2004 -65
Total: Before=28029, After=27943, chg -0.31%
add/remove: 0/0 grow/shrink: 0/0 up/down: 0/0 (0)
Data old new delta
Total: Before=17, After=17, chg +0.00%
add/remove: 2/0 grow/shrink: 0/2 up/down: 28/-129 (-101)
RO Data old new delta
dco_central_freq - 24 +24
div1_vals - 4 +4
odd_dividers 28 7 -21
even_dividers 144 36 -108
Total: Before=3600, After=3499, chg -2.81%
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220301173128.6988-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Remove the local onoff() implementation and adopt the
str_on_off() from linux/string_helpers.h.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220225234631.3725943-4-lucas.demarchi@intel.com
A new programming step was added to combo and TC PLL sequences.
If override_AFC_startup is set in VBT, driver should overwrite
AFC_startup value to 0x0 or 0x7 in PLL's div0 register.
The current understating is that only TGL needs this and all other
display 12 and newer platforms will have a older VBT or a newer VBT
with override_AFC_startup set to 0 but in any case there is a
drm_warn_on_once() to let us know if this is not true.
v2:
- specification updated, now AFC can be override to 0x0 or 0x7
- not using a union for div0 (Imre)
- following previous wrong vbt naming: bits instead of bytes (Imre)
BSpec: 49204
BSpec: 20122
BSpec: 49968
BSpec: 71360
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220216134059.25348-1-jose.souza@intel.com
Move struct intel_shared_dpll_funcs to intel_dpll_mgr.c, as no other
place needs to have access to it. We also don't need to have kernel-doc
documentation for file internal structures, so drop them while at it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119110528.2377899-1-jani.nikula@intel.com
Registers representing the MG/DKL TC PHYs (including the TC DPLLs which
exist inside the PHY) are only needed in a couple files and on specific
platforms; let's keep them separate from the general register pool.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220111051600.3429104-11-matthew.d.roper@intel.com
This power domain to disable DC states will be used in places outside
of DPLL, so making the name more generic.
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Caz Yokoyama <caz.yokoyama@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020003558.222198-1-jose.souza@intel.com
Move the PCH refclk stuff (including all the LPT/WPT
iCLKIP/CLKOUT_DP things) to its own file.
We also suck in the mPHY programming from intel_fdi.c
since we're the only caller.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015071625.593-2-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
Instead of directly accessing the TypeC port internal struct members,
add/use helpers to retrieve the corresponding properties.
No functional change.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-6-imre.deak@intel.com
