The decision to use DFP output format conversion capabilities should be
during compute_config phase.
This patch adds new member to crtc_state to represent the final
output_format to the sink. In case of a DFP this can be different than
the output_format, as per the format conversion done via the PCON.
This will help to store only the format conversion capabilities of the
DP device in intel_dp->dfp, and use crtc_state to compute and store the
configuration for color/format conversion for a given mode.
v2: modified the new member to crtc_state to represent the final
output_format that eaches the sink, after possible conversion by
PCON kind of devices. (Ville)
v3: Addressed comments from Ville:
-Added comments to clarify difference between sink_format and
output_format.
-Corrected the order of setting sink_format and output_format.
-Added readout for sink_format in get_pipe_config hooks.
v4: Set sink_format for intel_sdvo too. (Ville)
v5: Rebased.
v6: Fixed condition to go for YCbCr420 format for dp and hdmi. (Ville)
v7: Fix the condition to set sink_format for HDMI.
Set hdmi output_format simply as sink_format. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427125605.487769-2-ankit.k.nautiyal@intel.com
Rename PIPECONF to TRANSCONF to make it clear what it actually
applies to.
While the usual convention is to pick the earliers name I think
in this case it's more clear to use the later name. Especially
as even the register offset is in the wrong range (0x70000 vs.
0x60000) and thus makes it look like this is per-pipe.
There is one place in gvt that's doing something with TRANSCONF
while iterating with for_each_pipe(). So that might not be doing
the right thing for TRANSCODER_EDP, dunno. Not knowing what it
does I left it as is to avoid breakage.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Do the customary s/dev_priv/i915/ rename and aliasing
'dev' pointer removal. Though various register definitions
still depend on the magic 'dev_priv' variable so not
a 100% conversion.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130180540.8972-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
It's a bit confusing to have two cached EDIDs in struct intel_connector
with slightly different purposes. Make the distinction a bit clearer by
moving the EDID cached for eDP and LVDS panels at connector init time to
struct intel_panel, and name it fixed_edid. That's what it is, a fixed
EDID for the panels.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/328350ef918638928a8286cdbab3107c8258332d.1674643465.git.jani.nikula@intel.com
Convert all the connectors that use cached connector edid and
detect_edid to drm_edid.
Since drm_get_edid() calls drm_connector_update_edid_property() while
drm_edid_read*() do not, we need to call drm_edid_connector_update()
separately, in part due to the EDID caching behaviour in HDMI and
DP. Especially DP depends on the details parsed from EDID. (The big
behavioural change conflating EDID reading with parsing and property
update was done in commit 5186421cbf ("drm: Introduce epoch counter to
drm_connector"))
v6: Rebase on drm_edid_connector_add_modes()
v5: Fix potential uninitialized var use (kernel test robot <lkp@intel.com>)
v4: Call drm_edid_connector_update() after reading HDMI/DP EDID
v3: Don't leak vga switcheroo EDID in LVDS init (Ville)
v2: Don't leak opregion fallback EDID (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/eabb4de932841b38b34cc2818ea9fbf7c10224fd.1674643465.git.jani.nikula@intel.com
Lots of ADL machines out there with bogus VBTs that declare
two eDP child devices. In order for those to work we need to
figure out which power sequencer to use before we try the EDID
read. So let's do the panel VBT init early if we can, falling
back to the post-EDID init otherwise.
The post-EDID init panel_type=0xff approach of assuming the
power sequencer should already be enabled doesn't really work
with multiple eDP panels, and currently we just end up using
the same power sequencer for both eDP ports, which at least
confuses the wakeref tracking, and potentially also causes us
to toggle the VDD for the panel when we should not.
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125173156.31689-3-ville.syrjala@linux.intel.com
Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.
Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.
Also some places actually needed i915_irq.h too.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com
Since commit a5810f551d ("drm/i915: Allow more varied alternate
fixed modes for panels") intel_panel_add_edid_alt_fixed_modes()
no longer considers vrr vs. drrs separately. So no reason to
pass them as separate parameters either.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220927180615.25476-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
All the connectors are zero initialized so no need to clear
the *_allowed flags we don't support. Only leave the ones we want
to set. And while at it switch to booleans instead of ints.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Consolidate the scaling_mode property setup into a single
place.
The one slight complicateion here is that GMCH platforms can't
do the CENTER mode except on the LVDS port. But we can deal with
that by just checking the connector type.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-12-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Most of our encoder type cast stuff already operates on
intel_encoder rather than drm_encoder. Switch to_lvds_encoder()
over as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-6-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Each LFP may have different panel type which is stored in LFP data
data block. Based on the child device index respective panel-type/
panel-type2 field will be used.
v1: Initial rfc verion.
v2: Based on review comments from Jani,
- Used panel-type instead addition panel-index variable.
- DEVICE_HANDLE_* name changed and placed before DEVICE_TYPE_*
macro.
v3:
- passing intel_bios_encoder_data as argument of
intel_bios_init_panel(). Passing NULL to indicate encoder is not
initialized yet for dsi as current focus is to enable dual EDP. [Jani]
v4:
- encoder->devdata used which is initialized before from vbt
structure. [Jani]
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220620065138.5126-1-animesh.manna@intel.com
It seem that when dealing with VRR capable eDP panels we need
to accept fixed modes with variable vblank length (which is what
VRR varies dynamically). Typically the preferred mode seems to be
a non-VRR more (lowish dotclock/refresh rate + short vblank).
We also have examples where it looks like even the hblank length
is a bit different between the preferred mode vs. VRR mode(s).
So let's just accept anything that has matching hdisp+vdisp+flags.
v2: Document that is_alt_drrs_mode() is a subset of is_alt_vrr_mode() (Jani)
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/125
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220531191844.11313-4-ville.syrjala@linux.intel.com
Apparently when the VBT panel_type==0xff we should trawl through
the PNPID table and check for a match against the EDID. If a
match is found the index gives us the panel_type.
Tried to match the Windows behaviour here with first looking
for an exact match, and if one isn't found we fall back to
looking for a match w/o the mfg year/week.
v2: Rebase due to vlv_dsi changes
v3: Adjust to .get_panel_type() vfunc
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5545
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510104242.6099-14-ville.syrjala@linux.intel.com
Move the panel specific VBT parsing to happen during the
output probing stage. Needs to be done because the VBT
parsing will need to look at the EDID to determine
the correct panel_type on some machines.
We split the parsed VBT data (i915->vbt) along the same
boundary. For the moment we just hoist all the panel
specific stuff into connector->panel.vbt since that seems
like the most convenient place for eg. the backlight code.
Note that we simply drop the drrs type check from
intel_drrs_frontbuffer_update() since that operates on the whole
device rather than a specific connector/encoder. But the check
was just a micro optimization so removing it doesn't actually
mattter for correctness.
TODO: Lot's of cleanup to be done in the future. Eg. most of
the DSI stuff could probably be eliminated entirely and just
parsed on demand during DSI init.
v2: Note the intel_drrs_frontbuffer_update() change
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510104242.6099-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The intel_panel_add_edid_fixed_mode() vs.
intel_panel_add_edid_downclock_mode() split is not really
helpful. Let's just roll those into a single function so
that the connector init code doesn't have to care too much
about this. All we need to know is whether DRRS should be
allowed or not.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331112822.11462-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Rather than having the connector init get the fixed mode back from
intel_panel and then feed it straight back into intel_panel_init()
let's just make the fixed mode lookup put the mode directly onto
the panel's fixed_modes list. Avoids the pointless round trip and
opens the door for further enhancements to the fixed mode handling.
v2: Make the debug message correct by using intel_panel_drrs_type() (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331112822.11462-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Apart from the EDID and VBT based mechanism we also sometimes
use the encoder's current mode as the panel fixed mode. We
currently have the same code for that duplicated in two places.
Let's unify.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323182935.4701-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Rename intel_panel_vbt_fixed_mode() to
intel_panel_vbt_lfp_fixed_mode() to be more descriptive.
We'll have another VBT fixed mode function soon and we
don't want to confuse the two.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323182935.4701-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Use intel_panel_preferred_fixed_mode() for all the orientation
quirk setup and compute_is_dual_link_lvds()). All of these
happen after intel_panel_init() so the panel fixed_mode list
is already in place.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323182935.4701-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Replace all drm_mode_debug_printmodeline() calls with
DRM_MODE_FMT+DRM_MODE_ARG(). Makes the debug output a bit more
terse in places where we previously had a newline in the precedeing
drm_dbg_kms(), and avoids anything else sneaking in between the two
printk()s in all cases.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323182935.4701-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Abstract away the details on where we store the fixed/downclock
modes, and also how we select them. Will be useful for static
DRRS (aka. allowing the user to select the refresh rate for the
panel).
We pass in the user requested mode to intel_panel_fixed_mode()
so that in the future it may try to match the refresh rate.
And intel_panel_downclock_mode() gets passed the adjusted_mode
we actually chose to use so that it may find a suitable lower
resresh rate variant.
v2: Hook it up for all encoders
s/fixed_mode/adjusted_mode/ in intel_panel_downclock_mode() (Jani)
Elaborate on the choice or arguments for the functions (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220311172428.14685-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We want to eventually get rid of the connector->panel.fixed_mode
pointer so avoid using it during LVDS setup. Since this all
happens during the encoder init we already have the fixed_mode
around, just pass that in.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220311172428.14685-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Let's introduce a compute_config() helper for fixed mode panels.
For now all it does is the fixed_mode->adjusted_mode copy.
Note that with sDVO we have to ask the external encoder chip
to spit out our actual display timings for us, so the fixed_mode
to adjusted_mode copy done by intel_panel_compute_config() is
redundant, but we still want to use it to do other checks for us
later. We'll be fine so long as we only call it before
intel_sdvo_get_preferred_input_mode() overwrites adjusted_mode
with the timings from the encoder.
v2: Use intel_panel_compute_config() with sDVO
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210927185207.13620-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
All fixed mode panels should behave the same way when it comes to mode
filtering. Reuse the intel_panel_mode_valid() for all of them.
This changes the behaviour to match what we do for eDP, ie.
reject anything that doesn't exactly match the fixed mode
dimensions. Users can still manually provide different
sized modes which will be handled by the panel fitter just
as before. The difference is that we can no longer report
funny modes in the connector's mode list.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210923200109.4459-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Hoist the intel_de.h include from intel_display_types.h one
level up. I need this in order to untangle the include order
so that I can add tracepoints into intel_de.h.
This little cocci script did most of the work for me:
@find@
@@
(
intel_de_read(...)
|
intel_de_read_fw(...)
|
intel_de_write(...)
|
intel_de_write_fw(...)
)
@has_include@
@@
(
#include "intel_de.h"
|
#include "display/intel_de.h"
)
@depends on find && !has_include@
@@
+ #include "intel_de.h"
#include "intel_display_types.h"
@depends on find && !has_include@
@@
+ #include "display/intel_de.h"
#include "display/intel_display_types.h"
Cc: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-1-ville.syrjala@linux.intel.com
