If the output on a DP-alt link with its sink disconnected is kept
enabled for too long (about 20 sec), then some IOM/TCSS firmware timeout
will cause havoc on the PCI bus, at least for other GFX devices on it
which will stop powering up. Since user space is not guaranteed to do a
disabling modeset in time, switch such disconnected but active links to
TBT mode - which is without such shortcomings - with a 2 second delay.
If the above condition is detected already during the driver load/system
resume sanitization step disable the output instead, as at that point no
user space or kernel client depends on a consistent output state yet and
because subsequent atomic modeset on such connectors - without the
actual sink capabilities available - can fail.
An active/disconnected port as above will also block the HPD status of
other active/disconnected ports to get updated (stuck in the connected
state), until the former port is disabled, its PHY is disconnected and
a ~10 ms delay has elapsed. This means the link state for all TypeC
ports/CRTCs must be rechecked after a CRTC is disabled due to the above
reason. For this disconnect the PHY synchronously after the CRTC/port is
disabled and recheck all CRTCs for the above condition whenever such a
port is disabled.
To account for a race condition during driver loading where the sink is
disconnected after the above sanitization step and before the HPD
interrupts get enabled, do an explicit check/link reset if needed from
the encoder's late_register hook, which is called after the HPD
interrupts are enabled already.
v2:
- Handle an active/disconnected port blocking the HPD state update of
another active/disconnected port.
- Cancel the delayed work resetting the link also from the encoder
enable/suspend/shutdown hooks.
- Rebase on the earlier intel_modeset_lock_ctx_retry() addition,
fixing here the missed atomic state reset in case of a retry.
- Fix handling of an error return from intel_atomic_get_crtc_state().
- Recheck if the port needs to be reset after all the atomic state
is locked and async commits are waited on.
v3:
- Add intel_crtc_needs_link_reset(), instead of open-coding it,
keep intel_crtc_has_encoders(). (Ville)
- Fix state dumping and use a bitmask to track disabled CRTCs in
intel_sanitize_all_crtcs(). (Ville)
- Set internal in intel_atomic_state right after allocating it.
(Ville)
- Recheck all CRTCs (not yet force-disabled) after a CRTC is
force-disabled for any reason (not only due to a link state)
in intel_sanitize_all_crtcs().
- Reduce delay after CRTC disabling to 20ms, and use the simpler
msleep().
- Clarify code comment about HPD behaviour in
intel_sanitize_all_crtcs().
- Move all the TC link reset logic to intel_tc.c .
- Cancel the link reset work synchronously during system suspend,
driver unload and shutdown.
v4:
- Rebased on previous patch, which allows calling the TC port
suspend/cleanup handlers without modeset locks held; remove the
display driver suspended assert from the link reset work
accordingly.
v5: (Ville)
- Remove reset work canceling from intel_ddi_pre_pll_enable().
- Track a crtc vs. pipe mask in intel_sanitize_all_crtcs().
- Add reset_link_commit() to clarify the
intel_modeset_lock_ctx_retry loop.
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5860
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512195513.2699-2-imre.deak@intel.com
During HW readout/sanitization CRTCs can be disabled only if they don't
have an attached encoder (and so the encoder disable hooks don't need to
be called). An upcoming patch will need to disable CRTCs also with an
attached encoder, so add support for this.
For bigjoiner configs the encoder disabling hooks require the slave CRTC
states, so add these too to the atomic state. Since the connector atomic
state is already up-to-date when the CRTC is disabled the connector
state needs to be updated (reset) after the CRTC is disabled, make this
so. Follow the proper order of disabling first all bigjoiner slaves,
then any port synced CRTC slaves followed by the CRTC originally
requested to be disabled.
v2:
- Fix calculating the bigjoiner_masters mask in a port sync config,
(Ville)
- Keep _noatomic suffix in intel_crtc_disable_noatomic(). (Ville)
- Rebase on full CRTC state reset in this patchset, not requiring
resetting the bigjoiner state separately and (instead) resetting
the full atomic CRTC and related global state after all linked
pipes got disabled.
- Disable portsync slaves before a portsync master.
- Disable a portsync master if a linked portsync slave is disabled.
v3: (Ville)
- Use s/u32/u8 for transcoder and pipe masks.
- Use is_power_of_2() instead of hweight()==1.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-8-imre.deak@intel.com
Factor out a function setting the encoder and CRTC in the connector
atomic state, required by a follow up patch.
No functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-7-imre.deak@intel.com
Split calling the CRTC/encoder disabling hooks and updating the CRTC and
DPLL object states from updating the CRTC and atomic state and other
global state (BW, CDCLK, DBUF) into separate functions. When disabling a
bigjoiner configuration the latter step can be done only after all the
linked pipes are disabled, so this change prepares for that.
No functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-6-imre.deak@intel.com
During HW state readout/sanitization an up-to-date connector atomic
state will be required by a follow-up patch, which can disable CRTCs
with an encoder (and calling the correct encoder hooks happens via the
connector atomic state encoder pointer). So update the connector state
already before the CRTC sanitize/disable step. For now this doesn't make
a difference, since intel_modeset_update_connector_atomic_state() will
update/enable the atomic state only for connectors that have an enabled
encoder/CRTC. Such CRTCs/encoders will not be affected by
intel_sanitize_crtc().
v2: Add comment about why the connector state needs to be up-to-date.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-5-imre.deak@intel.com
Make sure that the CRTC state is reset correctly, as expected after
disabling the CRTC.
In particular this change will:
- Zero all the CSC blob pointers after intel_crtc_free_hw_state()
has freed them.
- Zero the shared DPLL and port PLL pointers and clear the
corresponding CRTC reference flag in the PLL state.
- Reset all the transcoder and pipe fields.
v2:
- Reset fully the CRTC state. (Ville)
- Clear pipe active flags in the DPLL state.
v3:
- Clear only the CRTC reference flag and add a helper for this.
(Ville)
v4:
- Rebased on previous patch, adding
intel_unreference_shared_dpll_crtc() separately. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-4-imre.deak@intel.com
If we have to force the hardware to go through a full modeset
due to eg. cdclk reprogramming, we need to preserve
crtc_state->inherited for all crtcs that have not otherwise
gone through the whole compute_config() stuff after connectors
have been detected.
Otherwise eg. cdclk induced modeset glk_force_audio_cdclk()
will clear the inherited flag, and thus the first real commit
coming from userspace later on will not be forced through
the full .compute_config() path and so eg. audio state may
not get properly recomputed.
But instead of adding all kinds of ad-hoc crtc_state->inherited
preservation hacks all over, let's change things so that we
only clear it for the crtcs directly included in userspace/client
initiated commits.
Should be far less fragile since now we just need to remember
to flag the internal commits, and not worry about where new
crtcs might get pulled in.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5260
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230328122357.1697-1-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
In order to move VRR enable/disable to a place where it's also
applicable to fastsets we need to be prepared to configure
the pipe into non-VRR mode initially, and then later switch
to VRR mode. To that end allow the active timings to be configured
in non-VRR mode temporarily even when the crtc_state says we're
going to be using VRR.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320203352.19515-5-ville.syrjala@linux.intel.com
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
The spec requires disabling the PLL on TC ports before disconnecting the
port's PHY. Prepare for that by moving the PLL disabling to the CRTC
disable hook, while disconnecting the PHY will be moved to the
post_pll_disable() encoder hook in the next patch.
v2: Move the call from intel_crtc_disable_noatomic() as well.
Reviewed-by: Mika Kahola <mika.kahola@intel.com> # v1
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-27-imre.deak@intel.com
Move intel_crtc_update_active_timings() into intel_vblank.c
where it more properly belongs.
Also do the s/dev_priv/i915/ modernization rename while at it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230310235828.17439-3-ville.syrjala@linux.intel.com
sizeof(struct intel_dmc) > 1024 bytes, allocated on all platforms as
part of struct drm_i915_private, whether they have DMC or not.
Allocate struct intel_dmc dynamically, and hide all the dmc details
behind an opaque pointer in intel_dmc.c.
Care must be taken to take into account all cases: DMC not supported on
the platform, DMC supported but not initialized, and DMC initialized but
not loaded. For the second case, we need to move the wakeref out of
struct intel_dmc.
v2:
- Rebase to kzalloc dmc after runtime pm get (Imre)
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230301122944.1298929-4-jani.nikula@intel.com
At least on some platforms (tested on ctg) the way
vgacon does screen blanking seems to flag constant
FIFO underruns, which means we have to be prepared
for them while the driver is loading. Currently
there is a time window between drm_crtc_init() and
intel_sanitize_fifo_underrun_reporting() during
which FIFO underrun reporting is in fact marked as
enabled. Thus we may end up mistakenly detecting
these bogus underruns during driver init.
Close the race by marking FIFO underrun reporting
as disabled prior to even registering the crtc.
intel_sanitize_fifo_underrun_reporting()/etc. will
re-enable it later if needed.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125185234.21599-2-ville.syrjala@linux.intel.com
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Get rid of the if ladder in intel_modeset_setup_hw_state() and hide a
number of functions by adding a .get_hw_state() hook to watermark
functions. At least for now, combine the platform specific sanitization
to the hw state readouts on the relevant platforms instead of adding a
separate hook for that.
There's a functional change on PCH split platforms: If i9xx_wm_init()
fails to read plane latency and chooses the nop functions,
ilk_wm_get_hw_state() won't get called for readout. Add the
ilk_init_lp_watermarks() call on that path which now won't be called in
.get_hw_state(), as it looks like the only thing that could make a
difference.
v2:
- Add missing static (kernel test robot)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6da32831e40606cc8b90491b83196917f2ce36ab.1676317696.git.jani.nikula@intel.com
Add new files intel_wm.[ch] and i9xx_wm.[ch] under display/ to hold
generic and pre-SKL watermark code, respectively. SKL+ watermark code
has already been split out to skl_watermark.[ch].
Use the _wm.[ch] naming for brevity; we may want to rename
skl_watermark.[ch] later accordingly.
Add new intel_wm_init() to call either skl_wm_init() or
i9xx_wm_init(i915) depending on the platform, the latter comprising of
the remains of intel_init_pm().
Sprinkle in some minor checkpatch fixes while moving the code.
v2:
- Rebase
- Fix copyright year
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ddf04a07a37f0368b3fef85d4ebb924082fec6cd.1676317696.git.jani.nikula@intel.com
Make sure that PIPEDMCs are enabled whenever the corresponding pipe is
enabled.
This is required at least by the latest ADLP v2.18 firmware, which adds
a new handler enabled by default and running whenever the pipe is
enabled at the vertical referesh rate.
Bspec: 50344, 67620
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102183324.862279-1-imre.deak@intel.com
Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.
Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.
Also some places actually needed i915_irq.h too.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com
Add an extra remapping step between the logical state of the LUTs
(hw.(de)gamma_lut) as specified via uapi/bigjoiner copy vs.
the actual state of the LUTs programmed into the hardware.
With this we should be finally able finish the (de)gamma
readout/state checker support for the remaining platforms
(ilk-skl) where the same hardware LUT can be positioned
either before or after the pipe CSC unit. Where we position
it depends on factors such as presence of the logical degamma
LUT, RGB vs. YCbCr output, full vs. limited RGB quantization
range.
Without the extra remapping step the state readout doesn't
really know whether the LUT read from the hardware is the
degamma or gamma LUT, and so we is unable to accurately store
it into our crtc state. With the remapping step we know
exactly where to put it given the order of the LUT vs. CSC
in the hardware state.
Only the initial hw->uapi state readout done during driver
load/resume still has the problem of not really knowing
what to do with the LUT(s). But we can just assume 1:1
mapping there and let subsequent commits fix things up.
Another benefit is that we now have a place for purely
internal LUTs, without complicating the bigjoiner uapi->hw
copy logic. This should prove useful for streamlining
glk degamma LUT handling.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221024161514.5340-3-ville.syrjala@linux.intel.com
Remove one use macro for_each_connector_on_encoder which
is only being used at intel_encoder_find_connector.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221020104635.874860-2-suraj.kandpal@intel.com
Pull all the skl+ watermark code (and the dbuf/sagv/ipc code
since it's all sort of intertwined and I'm too lazy to think
of a finer grained split right now) into its own file from the
catch-all intel_pm.c.
Also sneak in the s/dev_priv/i915/ rename while at it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908191646.20239-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
In another long-overdue cleanup, add a display sub-struct to
drm_i915_private, and start moving display related members there. Start
with display funcs that need a rename anyway to not collide with the new
display member.
Add a new header under display/ for defining struct intel_display.
Rename struct drm_i915_display_funcs to intel_display_funcs while at it.
v2:
- Fix multi-line comment style (Arun)
- Use display as the member name
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d44cae096b664f7015f8c797d6dfd4964226d4f8.1661346845.git.jani.nikula@intel.com
