The e1000e_config_hwtstamp function was incorrectly resetting the SYSTIM
registers every time the ioctl was being run. If you happened to be
running ptp4l and lost the PTP connect (removing cable, or blocking the
UDP traffic for example), then ptp4l will eventually perform a restart
which involves re-requesting timestamp settings. In e1000e this has the
unfortunate and incorrect result of resetting SYSTIME to the kernel
time. Since kernel time is usually in UTC, and PTP time is in TAI, this
results in the leap second being re-applied.
Fix this by extracting the SYSTIME reset out into its own function,
e1000e_ptp_reset, which we call during reset to restore the hardware
registers. This function will (a) restart the timecounter based on the
new system time, (b) restore the previous PPB setting, and (c) restore
the previous hwtstamp settings.
In order to perform (b), I had to modify the adjfreq ptp function
pointer to store the old delta each time it is called. This also has the
side effect of restoring the correct base timinca register correctly.
The driver does not need to explicitly zero the ptp_delta variable since
the entire adapter structure comes zero-initialized.
Reported-by: Brian Walsh <brian@walsh.ws>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The E1000_ICH_NVM_SIG_MASK value is shifted, out to the 31st bit, which
is the signed bit for signed constants. Mark these values as unsigned to
prevent compiler warnings and issues on platforms which a different
signed bit implementation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This prevents signed bitshift issues when the shift would overwrite the
signed bit, and prevents making this mistake in the future when copying
and modifying code.
Use GENMASK or the unsigned postfix for cases which aren't suitable for
BIT() macro.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
SYSTIMH:SYSTIML registers are incremented by 24-bit value TIMINCA[23..0]
er32(SYSTIML) are probably moderately expensive (they are pci bus reads).
Can we avoid one of them? Yes, we can.
If the SYSTIML value we see is smaller than 0xff000000, the overflow
into SYSTIMH would require at least two increments.
We do two reads, er32(SYSTIML) and er32(SYSTIMH), in this order.
Even if one increment happens between them, the overflow into SYSTIMH
is impossible, and we can avoid doing another er32(SYSTIML) read
and overflow check.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If two consecutive reads of the counter are the same, it is also
not an overflow. "systimel_1 < systimel_2" should be
"systimel_1 <= systimel_2".
Before the patch, we could perform an *erroneous* correction:
Let's say that systimel_1 == systimel_2 == 0xffffffff.
"systimel_1 < systimel_2" is false, we think it's an overflow,
we read "systimeh = er32(SYSTIMH)" which meanwhile had incremented,
and use "(systimeh << 32) + systimel_2" value which is 2^32 too large.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: intel-wired-lan@lists.osuosl.org
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
"incvalue" variable holds a result of "er32(TIMINCA) &
E1000_TIMINCA_INCVALUE_MASK" and used in "do_div(temp, incvalue)"
as a divisor.
Thus, "u64 incvalue" declaration is probably a mistake.
Even though it seems to be a harmless one, let's fix it.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed the file to use a consistent ret_val for return value checking.
Signed-off-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issues for disabling auto-negotiation and forcing
speed and duplex settings for the non-copper media.
For non-copper media, e1000_get_settings should return ETH_TP_MDI_INVALID for
eth_tp_mdix_ctrl instead of ETH_TP_MDI_AUTO so subsequent e1000_set_settings
call would not fail with -EOPNOTSUPP.
e1000_set_spd_dplx should not automatically turn autoneg back on for forced
1000 Mbps full duplex settings for non-copper media.
Cc: xe-kernel@external.cisco.com
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Steve Shih <sshih@cisco.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
a trans_start struct member exists twice:
- in struct net_device (legacy)
- in struct netdev_queue
Instead of open-coding dev->trans_start usage to obtain the current
trans_start value, use dev_trans_start() instead.
This is not exactly the same, as dev_trans_start also considers
the trans_start values of the netdev queues owned by the device
and provides the most recent one.
For legacy devices this doesn't matter as dev_trans_start can cope
with netdev trans_start values of 0 (they are ignored).
This is a prerequisite to eventual removal of dev->trans_start.
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
Modern Intel systems supports cross timestamping of the network device
clock and Always Running Timer (ART) in hardware. This allows the
device time and system time to be precisely correlated. The timestamp
pair is returned through e1000e_phc_get_syncdevicetime() used by
get_system_device_crosststamp(). The hardware cross-timestamp result
is made available to applications through the PTP_SYS_OFFSET_PRECISE
ioctl which calls e1000e_phc_getcrosststamp().
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: kevin.b.stanton@intel.com
Cc: kevin.j.clarke@intel.com
Cc: hpa@zytor.com
Cc: jeffrey.t.kirsher@intel.com
Cc: netdev@vger.kernel.org
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Christopher S. Hall <christopher.s.hall@intel.com>
[jstultz: Reworked to use new interface, commit message tweaks]
Signed-off-by: John Stultz <john.stultz@linaro.org>
i219 (4) and i219 (5) are the next LOM generations that will be
available on the next Intel platform (KabeLake).
This patch provides the initial support for the devices.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There have been bugs caused by HW ULP configuration settings not being
properly cleared after cable connect in V-Pro capable systems.
This caused HW to get out of sync occasionally.
The fix ensures that ULP settings are cleared in HW after
LAN cable re-connect.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on feedback from HW team, the configured value of the internal PHY
HW FIFO pointer gap was incorrect for non-gig speeds.
This patch provides the correct configuration.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several packet loss issues were reported for which the root cause for
them was an incorrect configuration of internal HW PHY clock gating
mechanism by SW.
This patch provides the correct mechanism.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to system level changes introduced in Skylake, ULP exit takes
significantly longer to occur. Therefore, driver must wait longer for.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the introduction of 82574 support in e1000e, the driver has worked
on the assumption that msi-x interrupt generation is automatically
disabled after each irq. As it turns out, this is not the case.
Currently, rx interrupts can fire multiple times before and during napi
processing. This can be a problem for users because frames that arrive
in a certain window (after adapter->clean_rx() but before
napi_complete_done() has cleared NAPI_STATE_SCHED) generate an interrupt
which does not lead to napi_schedule(). These frames sit in the rx queue
until another frame arrives (a tcp retransmit for example).
While the EIAC and CTRL_EXT registers are properly configured for irq
automask, the modification of IAM in e1000_configure_msix() is what
prevents automask from working as intended.
This patch removes that erroneous write and fixes interrupt rearming for
tx interrupts. It also clears IAME from CTRL_EXT. This is not strictly
necessary for operation of the driver but it is to avoid disruption from
potential programs that access the registers directly, like `ethregs -c`.
Reported-by: Frank Steiner <steiner-reg@bio.ifi.lmu.de>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In msi-x mode, there is no handler for the lsc interrupt so there is no
point in writing that to ics now that we always assume Other interrupts
are caused by lsc.
Reviewed-by: Jasna Hodzic <jhodzic@ucdavis.edu>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removes the ICR read in the other interrupt handler, uses EIAC to
autoclear the Other bit from ICR and IMS. This allows us to avoid
interference with Rx and Tx interrupts in the Other interrupt handler.
The information read from ICR is not needed. IMS is configured such that
the only interrupt cause that can trigger the Other interrupt is Link
Status Change.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
msi-x interrupts are not shared so there's no need to check if the
interrupt was really from this adapter.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function e1000e_up always returns 0. As such we can convert it to a
void and just ignore the results. This allows us to drop some code in a
couple spots as we no longer need to worry about non-zero return values.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i219-LM (3) is a LOM that will be available on systems with the
Lewisburg Platform Controller Hub (PCH) chipset from Intel.
This patch provides the initial support for the device.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to timing changes to the ME firmware in Skylake, this timer
needs to be increased to 300ms.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes possible division by zero in receive
interrupt handler when working without adaptive interrupt
moderation.
The adaptive interrupt moderation mechanism is typically
disabled on jumbo MTUs.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Leonid Bloch <leonid@daynix.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The local variable 'ret' doesn't serve much purpose so we might as well
clean it up.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per Eric Dumazet's previous patches:
(see commit (24d2e4a507) - tg3: use napi_complete_done())
Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout
GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>
Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS
igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816
i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.
Other drivers were only compile tested.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting ndo_features_check to passthru_features_check allows the driver
to skip the check for multiple tagged TSO packets and enables stacked
VLAN TSO.
Tested with I217-LM.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When e1000e_setup_rx_resources is failed in e1000_open,
e1000e_free_tx_resources in "err_setup_rx" segment is executed.
"writel(0, tx_ring->head)" statement in e1000_clean_tx_ring
in e1000e_free_tx_resources will cause a null poonter dereference(crash),
because "tx_ring->head" is only assigned in e1000_configure_tx
in e1000_configure, but it is after e1000e_setup_rx_resources.
This patch moves head/tail register writing to e1000_configure_tx/rx,
which can fix this problem. It is inspired by igb_configure_tx_ring
in the igb driver.
Specially, thank Alexander Duyck for his valuable suggestion.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the algorithm. Read systimel twice and check for overflow.
If there was no overflow, use the first value.
If there was an overflow, read systimeh again and use the second
systimel value.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes wrong locking usage.
In the context of slot reset, we should use lock.
And during resume, there is no need of lock.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) Replace spaces with tab.
2) Move ich8lan related define to the proper context.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements the EEE in Sx code so that it only applies to parts
that support EEE in Sx (as opposed to all parts that support EEE).
It also uses the existing eee_advert and eee_lp_abiliity to set just the
bits (100/1000) that should be set.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver lacks pm_qos_remove_request in error handling (err_req_irq) of
e1000_open, and qos request inserted by pm_qos_add_request is not removed.
This patch add pm_qos_remove_request in error handling to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In SPT hardware does not require this driver workaround.
Removed the conditional that caused K1 workaround execution on SPT.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to clocking changes in the Skylake platform, there was i219
data corruption. To work around this, HW team reported the need
to increase the minimum gap between the PHY FIFO read and write pointers.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In SPT/i219, there were CRC errors in speed 10/100 full duplex.
The solution given by the HW team is to increase the IPG from 8 to 0xC
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In i219, there is a hardware bug that prevented ULP entry.
A side effect of the original software fix for this was that EEE in
Sx couldn't be enabled.
This patch implements a modified flow that allows both ULP and EEE in Sx.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On power up, the MAC - PHY interface needs to be set to PCIe, even if
cable is disconnected. In ME systems, the ME handles this on exit from
Sx state. In non-ME, the driver handles it. Added a check for non-ME
system to the driver code that handles that.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000e_disable_aspm called pci_disable_link_state_locked which requires
pci_bus_sem to be held, but is also called from places where this semaphore
was not previously acquired. This patch implements two flavors of
disable_aspm, one that acquires the lock, and the other (_locked) which
should be called when the semaphore is already acquired.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump the version to reflect the driver changes and bug fixes for i219.
Also update the copyright, while we are at it.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
System would hang during execution of "ethtool -t <NIC>" for the same
reason that required flushing the descriptor rings. This fix disables
MULR for the loopback test to avoid the hang state.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Two issues involving systim were reported.
1. Clock is not running in the correct frequency
2. In some situations, systim values were not incremented linearly
This patch fixes the hardware clock configuration and the spurious
non-linear increment.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fix handles a hardware issue that prevented i219 from
working in legacy interrupts mode (IntMode=0)
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The indication that a descriptor ring flush is required was read from
FEXTNVM7 by mistake. It should be read from the PCI config space.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The condition under which the flush should occur was reversed. The fix
should be applied before any HW reset (unless followed by bus reset)
and before any power state transition from D0.
If E1000_FEXTNVM7_NEED_DESCRING_FLUSH bit is set in FEXTNVM7 and TDLEN > 0
the Tx ring should be flushed. (fixes ~95% of the hang states).
If the E1000_FEXTNVM7_NEED_DESCRING_FLUSH did not clear, we should also
flush the RX ring. Bug was caught by Alexander Duyck during a code review
when examining this fix.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes a warning that was reported by Yanjiang Jin
<yanjiang.jin@windriver.com> by implementing the solution suggested by
Alexander Duyck <alexander.h.duyck@redhat.com>.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After testing various cases, the conclusion is that the fix MUST be
executed BEFORE any event that the HW is reset or transition to D3.
To fix that I moved the execution to the relevant places but per
Alexander Duyck's review, ensure now that the DMA is valid and was not
freed before manipulating the ring.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
