In commit 97f95c93c8 ("iwlwifi: remove support for fw older than
-16.ucode") we accidentally changed the fw version reading code for
DVM devices. The code intended to remove the old fw version API,
because all MVM firmwares version 16 and above that we support don't
use it anymore. But DVM devices still use the old FW API.
Fix that by bringing the code back in.
Reported-by: Pat Erley <pat-lkml@erley.org>
Tested-by: Kalle Valo <kvalo@codeaurora.org>
Fixes: 97f95c93c8 ("iwlwifi: remove support for fw older than-16.ucode")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently reading the fw memory segments is done according to
addresses and data length that are hard-coded.
Lately a new tlv was appended to the ucode, that contains
the data type, length and address.
Parse this tlv, and in run-time store the memory segments length
and addresses that would be dumped upon a fw error.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
API version lower than 16 is not supported anymore - don't
load older ucode.
Remove code handling older versions.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
LQM stands for Link Quality Measurement. The firmware
will collect a defined set of statitics (see the
notification for details) that allow to know how busy
the medium is. The driver issues a request to the firmware
that includes the duration of the measurement (the firmware
needs to be on channel for that amount of time) and the
timeout (in case the firmware has a lot of offchannel
activities). If the timeout elapses, the firmware will
send partial results which are still valuable.
In case of disassociation / channel switch and alike, the
driver is in charge of stopping the measurements and the
firmware will reply with partial results.
The user space API for now is debugfs only and will be
implmemented in an upcoming patch.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of FW error, support dumping the UMAC internal txfifos.
To do so, support version 2 of shared memory cfg command, which
contains the sizes of the internal txfifos, and move the command
to the system group.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Gscan capabilities were updated with new capabilities supported
by the device. While at it, simplify the firmware support
conditional and move both conditions into the WARN() to make it
easier to undertand and use the unlikely() for both.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Till today, the ucode consisted of two d0 images - regular,
in which the usniffer wasn't enabled, and usniffer, in which the
usniffer logs were enabled.
Lately, the two images were unified, so there is only one d0 image,
in which the usniffer logs are enabled.
Add new TLV capability for supporting the consolidated images
(set 2, bit 13).
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Register cooling device in order to have the Thermal
Manager handle the device's power budget according to the sent
notifications.
The interface adds a new thermal cooling device to
/sys/class/thermal/ folder.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Up to today the driver was notified of the temperature from the FW
and decided whether to enter CT-kill or not.
From now on, the FW will decide when to enter CT-kill and will notify
the driver.
Add support for this notification.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Previous patches enabled the multi-queue rx path based on
iwl_mvm_has_new_rx_api() which returned false by default.
Change it to return the actual value based on the firmware
TLV which is now defined.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently firmware is configured to filter out beacons. In case
a beacon was changed - it is waking the host.
However, some vendors change their IEs frequently without any
significant change, and redundant wakeups are triggered as a
result.
As a solution disable beacon filtering when entering d0i3.
Instead, firmware will store the latest beacon and upon exiting
d0i3 it will send it up to the host, so the host can act upon
changes (if there were any).
This beacon will arrive as a dedicated notification - support it
as well.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable snoozing and U-APSD on P2P client. The firwmare will
support this only if the BSS vif is not associated.
Make this configurable by a constant variable and disable
it by default.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This will allow to collect the data when the firmware
sends a specific tx response status.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently when the driver is configured with wowlan parameters, and enters
D3 mode, the driver switches the FW image to D3, and when it exists
suspend, it reloads the D0 image.
If the firmware supports the consolidation of the D0 & D3 images there is
no need to load the D3 image on suspend, and no need to reload the D0
image on resume.
Do not switch images on suspend / resume, for firmwares that support
consolidated images.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow the user to configure a non-trigger session - a window
between triggers in which the driver won't collect fw debug data.
This can be useful when the frequent collection of fw data
has an impact on the performance, such as debugging
tx flows.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
New functionality for testing that is not relevant for
this driver has been added. This required an API change.
Add new cmd & response versions for the MCC update cmd & response.
Add new TLV indicating that the FW is using the new API.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware knows better what antenna to choose.
Old firmware still need the setting, so use a flag to know
if the driver should choose the antenna or if the firmware
can do it iself.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This will allow to catch different TDLS events and get the
firmware data when they occur.
Add empty TX_LATENCY trigger on the way to avoid mismatch
with trees in which this trigger is implemented.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When there's a bt-wifi contention that requires arbitration,
we use a priority-based mechanism to decide which comm wins.
Over time, use cases become more and more complex, with multiple
concurrent active links with different traffic types and different QoS
requirements, on both WiFi and BT sides.
This, in turn, requires us to elaborate our prioritization mechanism.
However, our legacy products included hw that does not supports this,
so selectively enable this on specific hw - as signaled by the firmware.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
