The firmware/hardware supports only 16 entries. Trying to use more can lead
to timeouts on some firmware versions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In the MT7915 info, the fields for the WLAN index / queue overlap with the
token id, and the MT_TX_FREE_PAIR bit indicates, which one is present.
If MT_TX_FREE_PAIR is set, skip processing the token index, since the data
will not be valid.
This fixes accidentally freeing tokens which are still in use by the
hardware with a wrong station pointer.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When looking for a MAC address slot, start by using main BSSID slots 1-3,
afterwards use 16 repeater mode BSSID slots, then start using the slots
usually used for AP mode.
This search order should prevent unnecessary conflicts with AP mode interfaces
on the same PHY
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The newer chipsets can deal with the same STA on multiple interfaces
Preparation for supporting more station interfaces
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is primarily for testing and can be used in combination with monitor
mode to make the card respond to packets sent to a specific MAC address.
For now this is only exposed as a debug/testing feature, later on the
approach might be used to support more concurrent station interfaces
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to improve driver throughput, convert status_work and net_work
to mt76 worker APIs.
Remove txrx_wq sdio workqueue since it is no longer used
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to reduce sdio bus contention, disable interrupts during
txrx_worker processing
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to improve driver throughput, convert txrx_work to mt76 worker
threads APIs.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt7663 tx and rx processing in the same workqueue in order to
reduce jitter that can hit tcp performances. This is a preliminary patch
to switch to mt76 workers APIs
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7615_load_patch in mt7615/mcu.c sometimes fails with:
mt7622-wmac 18000000.wmac: Failed to get patch semaphore
and returns -EAGAIN. But this error is returned all the way up to
mt7615_init_work with no actual retrial performed, leaving a
broken wireless phy.
Wait a bit and retry for up to 10 times before giving up.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The MCU field should contain a boolean 0/1, not the flag itself.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Read per-stream measurements every 100 ms and build a simple moving average.
Tested-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This code does not ensure that the whole buffer is initialized and none
of the callers check for errors so potentially none of the buffer is
initialized. Add a memset to eliminate this bug.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/X8ilOfVz3pf0T5ec@mwanda
ath.git patches for v5.11. Major changes:
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
The macro use will already have a semicolon.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201127175821.2756988-1-trix@redhat.com
Added multiple queues[BK,BE,VI,VO] to handle different priority data
packets. Before adding a packet to the queue, checked its priority from
the header, and then add to the suitable queue. The limit for each queue
is maintained separately. Also while passing the packets to the firmware
via VMM take care to select data packets based on priority and available
space.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201125114059.10006-6-ajay.kathat@microchip.com
Before returing from wilc_wlan_txq_add_mgmt_pkt() invoke tx_complete_fn()
callback to free up allocated memory for failure case.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201125114059.10006-4-ajay.kathat@microchip.com
Before returing from wilc_wlan_txq_add_net_pkt() invoke tx_complete_fn()
callback to free up allocated memory for failure cases.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201125114059.10006-3-ajay.kathat@microchip.com
Apart from a firmware binary the chip needs a config file used by the
FW. Add the config files to modinfo so that they can be read by
userspace.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201124120018.31358-1-matthias.bgg@kernel.org
Add toggle table related function to enhance WL throughput when WL coexist
with 4/18 HID.
The toggle table feature will toggle WL/BT priority table during WL slot,
it can decrease the impact from HID's frequently packets and prevent HID
lag.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-11-pkshih@realtek.com
Add modifications for A2DP interoperability issue of TWS earphones.
Some TWS earphones has low buffer size, so it's necessary to reduce
the slot period to let it get data more frequently.
(e.g. use 4-slot to replace the original 2-slot method).
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-10-pkshih@realtek.com
The original setting misses some necessary configuration.
Make coexistence slot align to beacon and check the connection situation
to know if we need to extend WLAN slot or not.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-9-pkshih@realtek.com
Some AP will not follow the power save request, or it cannot stop
transmission until its queue is empty. It may bring the decreasing of
data rate.
WLAN firmware will count is the AP still leaked packet after power save
handshake was done or not to enable WLAN slot extend mechanism.
The extend WLAN slot mechanism will extend the WLAN slot after power save
handshake, 5 ms per times, maximum is 5 times to received the leaked packet
to avoid the rate lower down.
And if the transmission was already locked at CCK rate.
The extended WLAN slot can also increase the opportunity that we can
received the CCK's long packet and be released from CCK rate.
While BT multi-link status was finished, there is possible that it still
has some packet remained for seconds. Add a timer to remain the multi-link
mechanism to protect WLAN Rx.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-8-pkshih@realtek.com
Add a flag to make decision whether the mechanism
should go into free-run mode or not.
For now, it is always false, the flag assignment will
be implemented later.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-7-pkshih@realtek.com
Add TDMA slot type setting for later usage.
Since the transmission of HID profile is very frequently,
it may bring a big impact to WLAN performance.
To change slot type, it can make mechanism be more flexible.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-6-pkshih@realtek.com
In free run mode, this WLAN info updating is only related to AFH
information, not related to the connection state, which is the current
implementation.
Always update WLAN info in free run mode now.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-5-pkshih@realtek.com
Update A2DP+PAN+WL mechanism for CPT(Coexistence Performance Test) to
enhance WL/BT performance at the environment that some specific AP are
existing.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-4-pkshih@realtek.com
Add message for debugging usage and the program flow is no change.
Add a variable reserved for WLAN firmware synchronize.
Add a group of variable to save BT packet counter, it will be
assigned as mechanism judgment in the future. Now it is just for
debug usage.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-3-pkshih@realtek.com
When WLAN entering or leaving, it's necessary to run coexistence mechanism
to ensure the setting matched current status.
Without calling rtw_coex_run_coex(), WLAN poor throughput or bad A2DP
quality may happen.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-2-pkshih@realtek.com
This reverts commit 2860615076.
Since actually Buffalo WI-U3-866D is falied to power on with the change.
The rtl8812au driver code to power on is same with the rtl8821a code.
But the rtl8821ae included rtl8821a does not support USB interface.
So seems that rtl8812au should be supported by rt1l8821a code with USB.
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201121003411.9450-1-ikegami.t@gmail.com
The NO_160 flag specifies if the device doesn't have 160 MHz support,
but we errorneously assumed the opposite. If the flag was set, we
were considering that 160 MHz was supported, but it's actually the
opposite. Fix it by inverting the bits, i.e. NO_160 is 0x1 and 160
is 0x0.
Fixes: d6f2134a38 ("iwlwifi: add mac/rf types and 160MHz to the device tables")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201202143859.375bec857ccb.I83884286b688965293e9810381808039bd7eedae@changeid
This commit updates the BMPS exit path to be consistent with downstream in
terms of exiting BMPS mode. Downstream sets the flag to send a NULL data
frame to the host on exiting BMPS.
This will tell the AP to send any queued frames to the STA immediately.
Verified the relevant bit toggle in wireshark.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201120021403.2646574-2-bryan.odonoghue@linaro.org
qmi_msg_handler[] and ath10k_qmi_ops are only used as input arguments
to qmi_handle_init() which accepts const pointers to both qmi_ops and
qmi_msg_handler. Make them const to allow the compiler to put them in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201122234031.33432-3-rikard.falkeborn@gmail.com
Should an error occur after calling 'ath10k_usb_create()', it should be
undone by a corresponding 'ath10k_usb_destroy()' call
Fixes: 4db66499df ("ath10k: add initial USB support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201122170358.1346065-1-christophe.jaillet@wanadoo.fr
