[WHY]
After unloading driver, driver would not disable DSC function.
At next loading driver, driver would power all DSC engines off.
When driver powered the active DSC off, the screen would be gray
until reprograming DSC relatived register correcntly.
[HOW]
1. Remove DSC Power down code into init_pipes()
2. Depend on the OTG mapping information and DSC status to skip
power off for the working DSC.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
- Adding a DM interface to enable DSC over eDP on Linux
- DSC over eDP will allow to power savings by reducing
the bandwidth required to support panel's modes
- Apply link optimization algorithm to reduce link bandwidth
when DSC is enabled
[how]
- Read eDP panel's DSC capabilities
- Apply DSC policy on eDP panel based on its DSC capabilities
- Enable DSC encoder's on the pipe
- Enable DSC on panel's side by setting DSC_ENABLE DPCD register
- Adding link optimization algorithm to reduce link rate or lane
count based
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In fast boot sequence, when change dispclk, otg is disabled but digfe
is enabled. This may cause dig fifo error.
[How]
Reset dig fifo after enable otg.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The MPC memory clocks should be powered down when not in use.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Every other CM LUT power down sequence is deferred to next vupdate as
memory powerdown updates immediately while selecting LUTs is double
buffered. Previous update to defer LUT power down missed GAMCOR and
DSCL, causing some visible flicker when entering/exiting fullscreen
video playback.
[HOW]
Update dpp deferred update loop to check for valid DPPs in res_pool
instead of referencing dcn_ip which turns out to not be populated during
runtime. Move GAMCOR and DSCL powerdown to dpp deferred updates.
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Disable root clock for dsc when not being used.
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
add display related cyan_skillfish files in.
makefile controlled by CONFIG_DRM_AMD_DC_DCN201 flag.
v2: squash in clang fixes from Harry, Nathan
v3: squash in missing CONFIG_DRM_AMD_DC check (Alex)
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Jun Lei <jun.lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Blnd, 3dlut, and shaper LUT select registers are double buffered, however
their accompanying LUT memory shutdown registers are not. As a result,
shutting down LUT memory immediately after setting a block to bypass causes
corruption as bypass only happens at next Vupdate.
[HOW]
Re-enable mem low power for CM block
Force optimization on next flip and disable LUT memory during optimization
sequence if LUT select field is then set to bypass
v2: squash in CONFIG_DRM_AMD_DC_DCN fix (Alex)
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Oliver Logush <oliver.logush@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prevent unnecessary wake up of DMCUB when ABM is enabled without PSR
enabled, driver will notify DMCUB to stop ABM's vertical interrupts
if vsync is disabled and steady state is reached.
[How]
Send inbox message to notify ABM pause based on vsync on/off
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Why:
Screen sometimes would have artifacts or blink once at the time when bpp
is dynamically changed.
How:
1. Changed to update PPS infopacket in frame mode instead of immediate mode
since other updates for bpp change are double-buffered.
2. Changed double-buffering enablement programming for DCN30 as advised by
ASIC team
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bing Guo <Bing.Guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Incorrect encoder assignments were being used while applying a new state
to hardware.
(1) When committing a new state to hardware requires resetting the
back-end, the encoder assignments of the current or old state should be
used when disabling the back-end; and the encoder assignments for the
next or new state should be used when re-enabling the back-end.
(2) Link training on hot plug could take over an encoder already in use
by another stream without first disabling it.
[How]
(1) Introduce a resource context 'link_enc_cfg_context' which includes:
- a mode to indicate when transitioning from current to next state.
- transient encoder assignments to use during this state transition.
Update the encoder configuration interface to respond to queries about
encoder assignment based on the mode of operation.
(2) Check if an encoder is already in use before attempting to perform
link training on hot plug.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Trying to enable multiple displays simultaneously exposed shortcomings
with the algorithm for dynamic link encoder assignment.
The main problems were:
- Assuming stream order remained constant across states would sometimes
lead to invalid DIG encoder assignment.
- Incorrect logic for deciding whether or not a DIG could support a
stream would also sometimes lead to invalid DIG encoder assignment.
- Changes in encoder assignment were wholesale while updating of the
pipe backend is incremental. This would lead to the hardware state not
matching the software state even with valid encoder assignments.
[How]
The following changes fix the identified problems.
- Use stream pointer rather than stream index to track streams across
states.
- Fix DIG compatibility check by examining the link signal type rather
than the stream signal type.
- Modify assignment algorithm to make incremental updates so software
and hardware states remain coherent.
Additionally:
- Add assertions and an encoder assignment validation function
link_enc_cfg_validate() to detect potential problems with encoder
assignment closer to their root cause.
- Reduce the frequency with which the assignment algorithm is executed.
It should not be necessary for fast state validation.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit "Revert "Add DPCD writes at key points" ".
The following patch will fix the system hang issue.
v2: squash in indentation warning fix
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A cleaner solution, only done once on boot.
[How]
Remove previous workaround and configure an extra
vmid one time on boot
Reviewed-by: Kazlauskas Nicholas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When an riommu invalidation request come at the same time as a pipe is
disabled there can be a case where DCN cannot ACK the request if only
one VMID is setup in the inuse list.
[How]
Setup a second unused VMID will work around the issue.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN 3x increased Line buffer size for DCHUB latency hiding, from 4 lines
of 4K resolution lines to 5 lines of 4K resolution lines. All Line
Buffer can be used as extended memory for P State change latency hiding.
The maximum number of lines is increased to 32 lines. Finally,
LB_MEMORY_CONFIG_1 (LB memory piece 1) and LB_MEMORY _CONFIG_2 (LB
memory piece 2) are not affected, no change in size, only 3 pieces is
affected, i.e., when all 3 pieces are used in both LB_MEMORY_CONFIG_0
and LB_MEMORY_CONFIG_3 (for 4:2:0) modes.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Extend existing state collection functions to add some additional
registers useful for debug, and add state collection function for DC
hubbub
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When requesting clocks from SMU which takes MHz inputs, DC will round
down KHz when converting to MHz, thus potentially requesting too low a
clock value.
[How]
Round up (ceil) when converting KHz to MHz for clock requests to SMU.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need for a separate flag now that DCN3.1 is not in bring up.
Fold into DRM_AMD_DC_DCN like previous DCN IPs.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Hardware has handed down a new sequence requiring the value of this
register be read from clk_mgr.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HW has handed down a new sequence that requires access to these
registers.
v2: squash in DCN3.1 fixes (Alex)
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HW has handed down a new sequence which requires access to the FIFO
ERRDET SW Override register.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
Add call to get the last used VTOTAL from DC
Signed-off-by: Jayendran Ramani <Jayendran.Ramani@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why + How]
Visual confirm has no asic-specific logic,
so we can refactor and unify these functions
that are currently spread out across multiple
dcn files.
Add a new hw sequencer interface update_visual_confirm_color,
and a new mpc function pointer set_bg_color.
This will allow visual confirm to updated independently
of MPCC blending updates.
v2: squash in DCN3.1 fixes
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for programming the DCN3.1 OPTC (Output Timing Controller)
HW Blocks:
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
There are no changes to OPP or MPC for DCN3.1, so the diagram will
include them in this patch.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for the DIO (Display IO) block of DCN3.1 which controls
legacy HDMI/DP stream/link encoding.
HW Blocks:
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Includes some updates to core logic for link encoder assignment and
future support for new high bandwidth output.
v2: squash in unused variable fix (Alex)
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds support for clock requests for the various parts of the DCN3.1 IP
and the interfaces and definitions for sending messages to SMU/PMFW.
Includes new support for z9/10, detecting SMU timeout and p-state
support enablement.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 3ca402375a.
Recent visual confirm changes are regressing the driver, causing a
black screen on boot in some green sardine configs, or visual confirm
is not updated at all.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are two issues with scaling calculations, odm recout
calculation and matching viewport to actual recout.
This change fixes both issues. Odm recout calculation via
special casing and viewport matching issue by reworking
the viewport calcualtion to use scaling ratios and recout
to derrive the required offset and size.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Added support for individual control for multiple back-light instances.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Visual confirm will indicate if driver is programming
the surface address.
Refactor is required because much of the visual confirm
logic is buried deep in the mpcc files.
In addition, visual confirm is not updated during fast updates.
[How]
In order to have visual confirm for driver flips, visual confirm
needs to be updated on every frame, including fast updates.
Add a new hw sequencer interface update_visual_confirm_color,
and a new mpc function pointer set_bg_color.
v2: drop unused variable (Alex)
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During the investigation on how to add visual confirmation on top of the
planes used by DCN, it becomes evident that the lack of information in
the code makes this work unnecessarily complicated. This commit
introduces a set of documentation related to the RECOUT operation in
order to make it easy for developers to navigate this set of functions.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Based on hardware team recommendation this additional dsc overhead
is only required for DP DSC.
[how]
Add a check for is_dp and only apply the overhead if this flag is set.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bring-up purpose code to disable DMUB calling into
SMU and timeout for MALL when SMU is not present.
[How]
Disable MALL when SMU is not present.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There is a bug in HW that causes P-State to hang when DPG is enabled in
certain conditions.
[HOW]
The solution is to force MIN_TTU_VBLANK register to maximum value
whenever DPG has been enabled.
Make stream do a full update on test pattern change, so that the TTUs
get updated.
When DPG is enabled, update the ttu_regs.min_ttu_vblank field of each
pipe in the stream's topology to the maximum value (0xffffff).
v2: squash in build fix for when DCN is not defined (Alex)
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some display endpoints may be programmably mapped to compatible link
encoders. The assignment of link encoders to links has to be dynamic to
accommodate the increased flexibility in comparison to conventional
display endpoints.
[How]
- Add link encoder assignment tracking variables.
- Execute link encoder assignment algorithm before enabling link and
release link encoders from links once they are disabled.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The pmfw structs are specific to the asic and should not be
present in base clk_mgr struct
v2: squash in SI fix (Alex)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
pflip interrupt would not be enabled promptly if a pipe is disabled
and re-enabled, causing flip_done timeout error during DP
compliance tests
[How]
Enable pflip interrupt upon pipe enablement
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently the creation of link encoder objects is tightly coupled to the
creation of link objects. Decoupling link encoder object creation is a
preliminary step in the process of allowing link encoders to be
dynamically assigned to links.
[How]
Add "minimal" link encoder objects which are not associated with any
link until required.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To process AUX transactions with DMUB using inbox1 and outbox1 mail boxes.
[HOW]
1) Added inbox1 command DMUB_CMD__DP_AUX_ACCESS to issue AUX commands
to DMUB in dc_process_dmub_aux_transfer_async(). DMUB processes AUX cmd
with DCN and sends reply back in an outbox1 message triggering an
outbox1 interrupt to driver.
2) In existing driver implementation, AUX commands are processed
synchronously by configuring DCN reg. But in DMUB AUX, driver sends an
inbox1 message and waits for a conditional variable (CV) which will be
signaled by outbox1 ISR.
3) As the driver holds dal and dc locks while waiting for CV, the outbox1
ISR is registered with noMutexWait set to true, which allows ISR to run
and signal CV. This sets a constraint on ISR to not modify variables
such as dc, dmub, etc.
4) Created dmub_outbox.c with dmub_enable_outbox_notification() to enable
outbox1 mailbox.
5) New mailbox address ranges allocated for outbox1 of size DMUB_RB_SIZE.
Created dmub functions for Outbox1: dmub_dcn20_setup_out_mailbox(),
dmub_dcn20_get_outbox1_wptr() and dmub_dcn20_set_outbox1_rptr().
6) Added functions dc_stat_get_dmub_notification() and
dmub_srv_stat_get_notification() to retrieve Outbox1 message.
7) Currently, DMUB doesn't opens DDC in AUX mode before issuing AUX
transaction. A workaround is added in dce_aux_transfer_dmub_raw() to
open in DDC in AUX mode for every AUX transaction.
8) Added dc debug option enable_dmub_aux_for_legacy_ddc enable/disable
DMUB AUX. This debug option is checked dce_aux_transfer_with_retries()
to select the method to process AUX transactions.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Vendor based fan noise improvement
[how]
Report timing synchronizable when DP streams time frame
difference is less than 0.05 percent. Adjust DP DTOs and
sync displays using MASTER_UPDATE_LOCK_DB_X_Y
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
