This patch fixes below warning reported by coccicheck:
./clk-gate2.c:57:5-8: Unneeded variable: "ret". Return "0" on line 68
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
noc/axi/ahb are bus clk, not peripheral clk.
Since peripheral clk has a limitation that for peripheral clock slice,
IP clock slices must be stopped to change the clock source.
However if the bus clk is marked as critical clk peripheral, the
assigned clock parent operation will fail.
So we added CLK_SET_PARENT_GATE flag to avoid glitch.
And add imx8m_clk_hw_composite_bus_critical for bus critical clock usage
Fixes: 936c383673 ("clk: imx: fix composite peripheral flags")
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reported-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1604229834-25594-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Protect against enabling/disabling the gate while we're
checking if it is enabled.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On some i.MX8 platforms, there are HW gates that share the same bit.
So in order to make this clock type more usable, use a mask to specify
how many bits belong to those HW gates.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Seems the logic here was wrong all along. For example, if
the cgr_val is 2 (0b10), the clk_gate2_reg_is_enabled would
report the clock as disabled. So check against cgr_val instead.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move all the register writing to the newly added clk_gate2_do_shared_clks
and call that everywhere need needed. Cleans up the code a little bit.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This was a hack which would allow multiple HW gates to be controlled
by a single bit. The only user of this is the imx_dev_clk_hw_gate_shared
which is not used anywhere as of now. Basically, complicates the logic
of the driver for no reason.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After commit e0d0d4d86c ("clk: imx8qxp: Support building i.MX8QXP clock
driver as module"), clk-scu.c and clk-imx8qxp.c are complied in one module,
thus there can be only one module_init() in those two files.
Commit 77d8f3068c ("clk: imx: scu: add two cells binding support")
introduced another module_init() in clk_scu.c which caused the errors
below.
To fix the issue, we can remove the unnecessary builtin_platform_driver
from clk_scu.c and directly register the driver in imx_clk_scu_init().
CC [M] drivers/clk/imx/clk-scu.o
In file included from ../include/linux/of_device.h:6,
from ../include/linux/of_platform.h:12,
from ../drivers/clk/imx/clk-scu.c:11:
../drivers/clk/imx/clk-scu.c: In function ‘imx_clk_scu_init’:
../drivers/clk/imx/clk-scu.c:176:35: error: ‘imx_clk_scu_driver’ undeclared (first use in this function); did you mean ‘imx_clk_scu_init’?
176 | return platform_driver_register(&imx_clk_scu_driver);
| ^~~~~~~~~~~~~~~~~~
../include/linux/platform_device.h:218:29: note: in definition of macro ‘platform_driver_register’
218 | __platform_driver_register(drv, THIS_MODULE)
| ^~~
../drivers/clk/imx/clk-scu.c:176:35: note: each undeclared identifier is reported only once for each function it appears in
176 | return platform_driver_register(&imx_clk_scu_driver);
| ^~~~~~~~~~~~~~~~~~
../include/linux/platform_device.h:218:29: note: in definition of macro ‘platform_driver_register’
218 | __platform_driver_register(drv, THIS_MODULE)
| ^~~
../drivers/clk/imx/clk-scu.c:177:1: error: control reaches end of non-void function [-Werror=return-type]
177 | }
| ^
At top level:
../drivers/clk/imx/clk-scu.c:470:31: warning: ‘imx_clk_scu_driver’ defined but not used [-Wunused-variable]
470 | static struct platform_driver imx_clk_scu_driver = {
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 77d8f3068c ("clk: imx: scu: add two cells binding support")
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pointer np is being initialized with a value that is never read
and it is being updated with a value later on. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A semicolon is not needed after a switch statement.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LPCG clock state may be lost when it's power domain is completely
off during system suspend/resume and we need save and restore the
state properly.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Used to support runtime pm.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
One LPCG controller supports up to 8 clock outputs while each of them
is fixed to 4 bits. It supports only gating function with fixed bits.
So we can use the clk-indices to fetch the corresponding clock idx from
device tree. With this way, we can write a generic LPCG clock drivers.
This patch add that support to parse clocks from device tree.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Clock state will be lost when its power domain is completely off
during system suspend/resume. So we save and restore the state
accordingly in suspend/resume callback.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bypass cpu power domains which are owned by ATF.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch implements the new two cells binding for SCU clocks.
The usage is as follows:
clocks = <&uart0_clk IMX_SC_R_UART_0 IMX_SC_PM_CLK_PER>
Due to each SCU clock is associated with a power domain, without power
on the domain, the SCU clock can't work. So we create platform devices
for each domain clock respectively and manually attach the required domain
before register the clock devices, then we can register clocks in the
clock platform driver accordingly.
Note because we do not have power domain info in device tree and the SCU
resource ID is the same for power domain and clock, so we use resource ID
to find power domains.
Later, we will also use this clock platform driver to support suspend/resume
and runtime pm.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
According to the latest RM (see Table 5-1. Clock Root Table),
both usdhc root clocks have the parent order as follows:
000 - 25M_REF_CLK
001 - SYSTEM_PLL1_DIV2
010 - SYSTEM_PLL1_CLK
011 - SYSTEM_PLL2_DIV2
100 - SYSTEM_PLL3_CLK
101 - SYSTEM_PLL1_DIV3
110 - AUDIO_PLL2_CLK
111 - SYSTEM_PLL1_DIV8
So the audio_pll2_out and sys3_pll_out have to be swapped.
Fixes: b80522040c ("clk: imx: Add clock driver for i.MX8MQ CCM")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reported-by: Cosmin Stefan Stoica <cosmin.stoica@nxp.com>
Link: https://lore.kernel.org/r/1602753944-30757-1-git-send-email-abel.vesa@nxp.com
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As i.MX21 support has been removed, get rid of its clock driver too.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mx35_clocks_init() has been used to register clocks on i.MX35
non-devicetree platforms.
Now that i.MX is a devicetree-only platform, it is safe to
remove mx35_clocks_init() as there are no more users.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mx31_clocks_init() has been used to register clocks on i.MX31
non-devicetree platforms.
Now that i.MX is a devicetree-only platform, it is safe to
remove mx31_clocks_init() as there are no more users.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mx27_clocks_init() has been used to register clocks on i.MX27
non-devicetree platforms.
Now that i.MX is a devicetree-only platform, it is safe to
remove mx27_clocks_init() as there are no more users.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A few words were misspelled in this comment.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix and add missing kerneldoc to fix compile warnings like:
drivers/clk/imx/clk-pfd.c:27: warning: Function parameter or member 'hw' not described in 'clk_pfd'
drivers/clk/imx/clk-pllv3.c:53: warning: Function parameter or member 'ref_clock' not described in 'clk_pllv3'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to RM, Page 574, Chapter 5.2.6.4.3 Peripheral clock slice,
"IP clock slices must be stopped to change the clock source.".
So we must have CLK_SET_PARENT_GATE flag to avoid glitch.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to RM, for peripheral clock slice,
"IP clock slices must be stopped to change the clock source.".
So we must have CLK_SET_PARENT_GATE flag to avoid glitch.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The root clock slice at offset 0xbf80 should be memrepair
clock, so correct it. And this clock should be always on
to make sure the memory repair function can works well.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The root clock slice at 0xbf00 is media_ldb clock,
not csi_phy2_ref, so correct it.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the clock for CRC block allowing it to be enabled by consumers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is better to explicitly include the required header file rather
then get it through some recursive include.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change configuration to "tristate", add module author, description and
license to support building i.MX8QXP clock drivers as module.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change configuration to "tristate", add module author, description
and license to support building i.MX8M SoCs clock driver as module.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add CONFIG_CLK_xxx for i.MX ARMv7 platforms, and use it as build option
instead of CONFIG_SOC_xxx, the CONFIG_CLK_xxx will be selected by default
according to CONFIG_SOC_xxx.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are more and more requirements of building SoC specific drivers
as modules, add support for building i.MX common clock driver as module
to meet the requirement.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use readl_relaxed() instead of __raw_readl(), and use BIT(x)
instead of (1 << X) to fix below build warning reported by kernel
test robot:
drivers/clk/imx/clk-imx6sl.c:149:49: warning: Shifting signed 32-bit
value by 31 bits is undefined behaviour [shiftTooManyBitsSigned]
while (!(__raw_readl(anatop_base + PLL_ARM) & BM_PLL_ARM_LOCK))
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Add RTC related clks on Ingenic SoCs
- Support USB PHY clks on Ingenic SoCs
* clk-fallthru:
clk: davinci: Use fallthrough pseudo-keyword
clk: imx: Use fallthrough pseudo-keyword
* clk-ingenic:
clk: X1000: Add support for calculat REFCLK of USB PHY.
clk: JZ4780: Reformat the code to align it.
clk: JZ4780: Add functions for enable and disable USB PHY.
clk: Ingenic: Add RTC related clocks for Ingenic SoCs.
dt-bindings: clock: Add tabs to align code.
dt-bindings: clock: Add RTC related clocks for Ingenic SoCs.
* clk-tegra:
clk: tegra: pll: Improve PLLM enable-state detection
* clk-sirf:
clk: clk-atlas6: fix return value check in atlas6_clk_init()
* clk-qoriq:
clk: qoriq: add LS1021A core pll mux options
Add mu root clk for mu mailbox usage.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the bus clk use imx8m_clk_hw_composite_bus, then
we could avoid possible issue when setting mux of the clk.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Introduce imx8m_clk_hw_composite_bus api for bus clk root slice usage.
Because the mux switch sequence issue, we could not reuse Peripheral
Clock Slice code, need use composite specific mux operation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CORE/BUS root slice has following design, simplied graph:
The difference is core not have pre_div block.
A composite core/bus clk has 8 inputs for mux to select, saying clk[0-7].
It support target(smart) interface and normal interface. Target interface
is exported for programmer easy to configure ccm root. Normal interface
is also exported, but we not use it in our driver, because it will
introduce more complexity compared with target interface.
The normal interface simplified as below:
SEL_A GA
+--+ +-+
| +->+ +------+
CLK[0-7]--->+ | +-+ |
| | | +----v---+ +----+
| +--+ |pre_diva+----> | +---------+
| +--------+ |mux +--+post_div |
| +--+ |pre_divb+--->+ | +---------+
| | | +----^---+ +----+
+--->+ | +-+ |
| +->+ +------+
+--+ +-+
SEL_B GB
The mux in the upper pic is not the target interface MUX, target
interface MUX is hiding SEL_A and SEL_B. When you choose clk[0-7],
you are actually writing SEL_A or SEL_B depends on the internal
counter which will also control the internal "mux".
The target interface simplified as below which is used by Linux Kernel:
CLK[0-7]--->MUX-->Gate-->pre_div-->post_div
A requirement of the Target Interface's software is that the
target clock source is active, it means when setting SEL_A, the
current input clk to SEL_A must be active, same to SEL_B.
We touch target interface, but hardware logic actually also need
configure normal interface.
There will be system hang, when doing the following steps:
The initial state:
SEL_A/SEL_B are both sourcing from clk0, the internal counter
choose SEL_A.
1. switch mux from clk0 to clk1
The hardware logic will choose SEL_B and configure SEL_B to clk1.
SEL_A no changed.
2. gate off clk0
Disable clk0, then the input to SEL_A is off.
3. swtich from clk1 to clk2
The hardware logic will choose SEL_A and configure SEL_A to clk2,
however the current SEL_A input clk0 is off, the system hang.
The solution to fix the issue is in step 1, write twice to
target interface MUX, it will make SEL_A/SEL_B both sources
from clk1, then no need to care about the state of clk0. And
finally system performs well.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Migrate A53 clk root to use composite core clk type. It
will simplify code and make it easy to use composite
specific mux operation.
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use imx8m_clk_hw_composite_core to simpliy clks that belong to
core clk slice.
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Inspried from
commit e8688fe8df ("clk: imx8mn: Define gates for pll1/2 fixed dividers")
On imx8mp there are 9 fixed-factor dividers for SYS_PLL1 and SYS_PLL2
each with their own gate. Only one of these gates (the one "dividing" by
one) is currently defined and it's incorrectly set as the parent of all
the fixed-factor dividers.
Add the other 8 gates to the clock tree between sys_pll1/2_bypass and
the fixed dividers.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Same to i.MX8MN/i.MX8MM, pll BYPASS bit should be kept inside pll
driver for glitchless freq setting following spec. If exposing the
bit, that means pll driver and clk driver has two paths to touch
this bit, which is wrong.
So use EXT_BYPASS bit here.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The parent settings have been moved to dtsi, we no need to
set parent here. And clk_hw_set_parent will trigger lockdep warning,
because this api not have prepare_lock.
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
