In the event of a fatal firmware error, firmware will notify the host
and then it will proceed to do core reset when it sees that all functions
have disabled Bus Master. To prevent Master Aborts and other hard
errors, we need to quiesce all activities in addition to disabling Bus
Master before the chip goes into core reset.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the event of a fatal firmware error, we want to disable IRQ early
in the recovery sequence. This change will allow it to be called
safely again as part of the normal shutdown sequence.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Up until now, we don't need to keep track of this state because NAPI
is always enabled once and disabled once during bring up and shutdown.
For better error recovery in subsequent patches, we want to quiesce
the device earlier during fatal error conditions. The normal shutdown
sequence will disable NAPI again and the flag will prevent disabling
NAPI twice.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This code to check if we have reached the maximum wait time after
firmware reset is used multiple times. Add a helper function to
do this.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Firmware may be in the middle of reset when the driver tries to do ifup.
In that case, firmware will return a special error code and the driver
will retry 10 times with 50 msecs delay after each retry.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drawing a hard line on aborted resets prevents a NIC open in
some scenarios that may otherwise be recoverable. For example,
if a firmware recovery happened while a PF was down and an
attempt was made to bring up an associated VF in this state,
then it was impossible to ever bring up this VF without a
rebind or reload of its driver.
Attempt to reinitialize the firmware when an aborted reset (or
failed init after a reset) is discovered during open - it may
succeed. Also take care to allow the user to retry opening the
NIC even after an aborted reset.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Firmware is capable of generating asynchronous debug notifications.
The event data is opaque to the driver and is simply logged. Debug
notifications can be enabled by turning on hardware status messages
using the ethtool msglvl interface.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The timeout period for firmware messages is passed to the driver
from the firmware in the response of the first command. This
timeout period is multiplied by a factor for certain long
running commands such as NVRAM commands. In some cases, the
timeout period can become really long and it can cause hung task
warnings if firmware has crashed or is not responding. To avoid
such long delays, cap all firmware commands to a max timeout value
of 40 seconds.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If firmware is in reset or in bad state, it won't be able to return
VPD data. Move bnxt_vpd_read_info() until after bnxt_fw_init_one_p1()
successfully returns. By then we would have established proper
communications with the firmware.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The first HWRM_VER_GET message to firmware during probe may timeout if
firmware is under reset. This can happen during hot-plug for example.
On P5 and newer chips, we can check if firmware is in the boot stage by
reading a status register. Retry 5 times if the status register shows
that firmware is not ready and not in error state.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add missing support for handling NO_MASTER crashes while ports are
administratively down (ifdown). On some SoC platforms, the driver
needs to assist the firmware to recover from a crash via OP-TEE.
This is performed in a similar fashion to what is done during driver
probe.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define macros to check for the various states in the lower 16 bits of
the health register. Replace the C code that checks for these values
with the newly defined macros.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Updates to backing store APIs, QoS profiles, and push buffer initial
index support.
Since the new HWRM_FUNC_BACKING_STORE_CFG message size has increased,
we need to add some compat. logic to fall back to the smaller legacy
size if firmware cannot accept the larger message size. The new fields
added to the structure are not used yet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When working on the PCI VPD code I also tested with a Broadcom BCM95719
card. tg3 uses internal NVRAM access with this card, so I forced it to
PCI VPD mode for testing. PCI VPD access fails
(i + PCI_VPD_LRDT_TAG_SIZE + j > len) because only TG3_NVM_VPD_LEN (256)
bytes are read, but PCI VPD has 400 bytes on this card.
So add a constant TG3_NVM_PCI_VPD_MAX_LEN that defines the maximum
PCI VPD size. The actual VPD size is returned by pci_read_vpd().
In addition it's not worth looping over pci_read_vpd(). If we miss the
125ms timeout per VPD dword read then definitely something is wrong,
and if the tg3 module loading is killed then there's also not much
benefit in retrying the VPD read.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/cb9e9113-0861-3904-87e0-d4c4ab3c8860@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Conflicts:
drivers/net/can/dev.c
commit 03f16c5075 ("can: dev: can_restart: fix use after free bug")
commit 3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
Code move.
drivers/net/dsa/b53/b53_common.c
commit 8e4052c32d ("net: dsa: b53: fix an off by one in checking "vlan->vid"")
commit b7a9e0da2d ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Field rename.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the error path, it should goto the error handling label to free
allocated memory rather than directly return.
Fixes: 31bc72d976 ("net: systemport: fetch and use clock resources")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210120044423.1704-1-bianpan2016@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-01-16
1) Extend atomic operations to the BPF instruction set along with x86-64 JIT support,
that is, atomic{,64}_{xchg,cmpxchg,fetch_{add,and,or,xor}}, from Brendan Jackman.
2) Add support for using kernel module global variables (__ksym externs in BPF
programs) retrieved via module's BTF, from Andrii Nakryiko.
3) Generalize BPF stackmap's buildid retrieval and add support to have buildid
stored in mmap2 event for perf, from Jiri Olsa.
4) Various fixes for cross-building BPF sefltests out-of-tree which then will
unblock wider automated testing on ARM hardware, from Jean-Philippe Brucker.
5) Allow to retrieve SOL_SOCKET opts from sock_addr progs, from Daniel Borkmann.
6) Clean up driver's XDP buffer init and split into two helpers to init per-
descriptor and non-changing fields during processing, from Lorenzo Bianconi.
7) Minor misc improvements to libbpf & bpftool, from Ian Rogers.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (41 commits)
perf: Add build id data in mmap2 event
bpf: Add size arg to build_id_parse function
bpf: Move stack_map_get_build_id into lib
bpf: Document new atomic instructions
bpf: Add tests for new BPF atomic operations
bpf: Add bitwise atomic instructions
bpf: Pull out a macro for interpreting atomic ALU operations
bpf: Add instructions for atomic_[cmp]xchg
bpf: Add BPF_FETCH field / create atomic_fetch_add instruction
bpf: Move BPF_STX reserved field check into BPF_STX verifier code
bpf: Rename BPF_XADD and prepare to encode other atomics in .imm
bpf: x86: Factor out a lookup table for some ALU opcodes
bpf: x86: Factor out emission of REX byte
bpf: x86: Factor out emission of ModR/M for *(reg + off)
tools/bpftool: Add -Wall when building BPF programs
bpf, libbpf: Avoid unused function warning on bpf_tail_call_static
selftests/bpf: Install btf_dump test cases
selftests/bpf: Fix installation of urandom_read
selftests/bpf: Move generated test files to $(TEST_GEN_FILES)
selftests/bpf: Fix out-of-tree build
...
====================
Link: https://lore.kernel.org/r/20210116012922.17823-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the FW tells the driver to retry the INSTALL_UPDATE command after
it has cleared the NVM area, the driver is not clearing the previously
used ALLOWED_TO_DEFRAG flag. As a result the FW tries to defrag the NVM
area a second time in a loop and can fail the request.
Fixes: 1432c3f6a6 ("bnxt_en: Retry installing FW package under NO_SPACE error condition.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function bnxt_get_ulp_stat_ctxs() does not count the stats contexts
used by the RDMA driver correctly when the RDMA driver is freeing the
MSIX vectors. It assumes that if the RDMA driver is registered, the
additional stats contexts will be needed. This is not true when the
RDMA driver is about to unregister and frees the MSIX vectors.
This slight error leads to over accouting of the stats contexts needed
after the RDMA driver has unloaded. This will cause some firmware
warning and error messages in dmesg during subsequent config. changes
or ifdown/ifup.
Fix it by properly accouting for extra stats contexts only if the
RDMA driver is registered and MSIX vectors have been successfully
requested.
Fixes: c027c6b4e9 ("bnxt_en: get rid of num_stat_ctxs variable")
Reviewed-by: Yongping Zhang <yongping.zhang@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
UniMAC is integrated into multiple Broadcom's Ethernet controllers so
use a shared header file for it and avoid some code duplication.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Link: https://lore.kernel.org/r/20210107180051.1542-2-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
UniMAC is a hardware block commonly used in Broadcom Ethernet controllers
that should get its own header file. Not every controller has it mapped at
the 0x800 offset so add bgmac access helpers. They will allow using
shared register defines.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210107180051.1542-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SYSTEMPORT driver maps each port of the embedded Broadcom DSA switch
port to a certain queue of the master Ethernet controller. For that it
currently uses a dedicated notifier infrastructure which was added in
commit 60724d4bae ("net: dsa: Add support for DSA specific notifiers").
However, since commit 2f1e8ea726 ("net: dsa: link interfaces with the
DSA master to get rid of lockdep warnings"), DSA is actually an upper of
the Broadcom SYSTEMPORT as far as the netdevice adjacency lists are
concerned. So naturally, the plain NETDEV_CHANGEUPPER net device notifiers
are emitted. It looks like there is enough API exposed by DSA to the
outside world already to make the call_dsa_notifiers API redundant. So
let's convert its only user to plain netdev notifiers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It is a bit strange to see something as specific as Broadcom SYSTEMPORT
bits in the main DSA include file. Move these away into a separate
header, and have the tagger and the SYSTEMPORT driver include them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All UDP tunnel port management is now routed via udp_tunnel_nic
infra directly. Remove the old callbacks.
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All of the OF code that is used has stubbed and will compile and link
just fine, keeping COMPILE_TEST is enough.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210106191546.1358324-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use existing rx processed count to track against budget, thereby making
budget decrement operation redundant.
rx_desc_count can be calculated outside the rx loop, making the loop a
bit smaller.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can increase the efficiency of rx path by using buffers to receive
packets then build SKBs around them just before passing into the network
stack. In contrast, preallocating SKBs too early reduces CPU cache
efficiency.
Check if we're in NAPI context when refilling RX. Normally we're almost
always running in NAPI context. Dispatch to napi_alloc_frag directly
instead of relying on netdev_alloc_frag which does the same but
with the overhead of local_bh_disable/enable.
Tested on BCM6328 320 MHz and iperf3 -M 512 to measure packet/sec
performance. Included netif_receive_skb_list and NET_IP_ALIGN
optimizations.
Before:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.00 sec 49.9 MBytes 41.9 Mbits/sec 197 sender
[ 4] 0.00-10.00 sec 49.3 MBytes 41.3 Mbits/sec receiver
After:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-30.00 sec 171 MBytes 47.8 Mbits/sec 272 sender
[ 4] 0.00-30.00 sec 170 MBytes 47.6 Mbits/sec receiver
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rx SKB ring use the same code for cleanup at various points.
Combine them into a function to reduce lines of code.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TQM rings are hardware resources that require host context memory
managed by the driver. The driver supports up to 9 TQM rings and
the number of rings to use is requested by firmware during run-time.
Cap this number to the maximum supported to prevent accessing beyond
the array. Future firmware may request more than 9 TQM rings. Define
macros to remove the magic number 9 from the C code.
Fixes: ac3158cb01 ("bnxt_en: Allocate TQM ring context memory according to fw specification.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A recent change skips sending firmware messages to the firmware when
pci_channel_offline() is true during fatal AER error. To make this
complete, we need to move the re-initialization sequence to
bnxt_io_resume(), otherwise the firmware messages to re-initialize
will all be skipped. In any case, it is more correct to re-initialize
in bnxt_io_resume().
Also, fix the reverse x-mas tree format when defining variables
in bnxt_io_slot_reset().
Fixes: b340dc680e ("bnxt_en: Avoid sending firmware messages when AER error is detected.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver is already allocating receive buffers of 2KiB and the
Ethernet MAC is configured to accept frames up to UMAC_MAX_MTU_SIZE.
Fixes: bfcb813203 ("net: dsa: configure the MTU for switch ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20201218173843.141046-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the 'register_netdev()' call fails, we must undo a previous
'bcmgenet_mii_init()' call.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201212182005.120437-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current scheme allocates a DMA buffer as big as the requested
firmware package file and DMAs the contents to firmware in one
operation. The buffer size can be several hundred kilo bytes and
the driver may not be able to allocate the memory. This will cause
firmware upgrade to fail.
Improve the scheme by using smaller DMA blocks and calling firmware to
DMA each block in a batch mode. Older firmware can cause excessive
NVRAM erases if the block size is too small so we try to allocate a
256K buffer to begin with and size it down successively if we cannot
allocate the memory.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In bnxt_flash_package_from_fw_obj(), if firmware returns the NO_SPACE
error, call __bnxt_flash_nvram() to create the UPDATE directory and
then loop back and retry one more time.
Since the first try may fail, we use the silent version to send the
firmware commands.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On NICs with a smaller NVRAM, FW installation may fail after multiple
updates due to fragmentation. The driver can retry when FW returns
a special error code. To faciliate the retry, we restructure the
logic that performs the flashing in a loop. The actual retry logic
will be added in the next patch.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This function will be modified in the next patch to retry flashing
the firmware in a loop. To facilate that, we rearrange the code so
that the steps that only need to be done once before the loop will be
moved to the top of the function.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor bnxt_flash_nvram() into __bnxt_flash_nvram() that takes an
additional dir_item_len parameter. The new function will be used
in subsequent patches with the dir_item_len parameter set to create
the UPDATE directory during flashing.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-12-03
The main changes are:
1) Support BTF in kernel modules, from Andrii.
2) Introduce preferred busy-polling, from Björn.
3) bpf_ima_inode_hash() and bpf_bprm_opts_set() helpers, from KP Singh.
4) Memcg-based memory accounting for bpf objects, from Roman.
5) Allow bpf_{s,g}etsockopt from cgroup bind{4,6} hooks, from Stanislav.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (118 commits)
selftests/bpf: Fix invalid use of strncat in test_sockmap
libbpf: Use memcpy instead of strncpy to please GCC
selftests/bpf: Add fentry/fexit/fmod_ret selftest for kernel module
selftests/bpf: Add tp_btf CO-RE reloc test for modules
libbpf: Support attachment of BPF tracing programs to kernel modules
libbpf: Factor out low-level BPF program loading helper
bpf: Allow to specify kernel module BTFs when attaching BPF programs
bpf: Remove hard-coded btf_vmlinux assumption from BPF verifier
selftests/bpf: Add CO-RE relocs selftest relying on kernel module BTF
selftests/bpf: Add support for marking sub-tests as skipped
selftests/bpf: Add bpf_testmod kernel module for testing
libbpf: Add kernel module BTF support for CO-RE relocations
libbpf: Refactor CO-RE relocs to not assume a single BTF object
libbpf: Add internal helper to load BTF data by FD
bpf: Keep module's btf_data_size intact after load
bpf: Fix bpf_put_raw_tracepoint()'s use of __module_address()
selftests/bpf: Add Userspace tests for TCP_WINDOW_CLAMP
bpf: Adds support for setting window clamp
samples/bpf: Fix spelling mistake "recieving" -> "receiving"
bpf: Fix cold build of test_progs-no_alu32
...
====================
Link: https://lore.kernel.org/r/20201204021936.85653-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The CNIC kconfig symbol selects UIO and UIO depends on MMU.
Since 'select' does not follow dependency chains, add the same MMU
dependency to CNIC.
Quietens this kconfig warning:
WARNING: unmet direct dependencies detected for UIO
Depends on [n]: MMU [=n]
Selected by [m]:
- CNIC [=m] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_BROADCOM [=y] && PCI [=y] && (IPV6 [=m] || IPV6 [=m]=n)
Fixes: adfc5217e9 ("broadcom: Move the Broadcom drivers")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Rasesh Mody <rmody@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Link: https://lore.kernel.org/r/20201129070843.3859-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add napi_id to the xdp_rxq_info structure, and make sure the XDP
socket pick up the napi_id in the Rx path. The napi_id is used to find
the corresponding NAPI structure for socket busy polling.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/bpf/20201130185205.196029-7-bjorn.topel@gmail.com
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>