When installing a (new) key, set the replay counter so that
after FW restart the firmware has the correct value of the
replay counters.
This doesn't have a large effect - for frames that reach
the driver, it will do a replay check, and when installing
a new key, the counter is normally zero to start with (not
for GTK though, if joining the BSS for the first time).
Since this only affects frames handled entirely by the FW,
and that's restricted to a few unicast management frames,
the only affect here is for those after a firmware restart.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.1cedf2ca7bb6.I2e609c28eaa301436e6740f4f1beca838f69a96a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
EAPOL failure results in deauthentication with various reasons, not
related to AUTH failure specifically, so we just merge AUTH failure
with failed to assoc to AP.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.2ff350d85eab.I02c5b5d29c0d5c2e014bd1081b07ed33772ae04d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for discovery of hidden networks on the 6GHz band,
by including the scan request direct SSIDs in the FW scan request
command:
- In case a short SSID matches one of the direct SSIDs in the scan
request command, add the matching SSID in the same offset in the
'direct_ssids' array.
- Otherwise, add the SSID in one of the available slots.
Additionally, as a preparation to handle hidden APs, refactor
iwl_mvm_umac_scan_cfg_channels_v6_6g() the function.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.ffb540a70212.Ia2bb9bc9435b833820bcc7dc30adcedb5a5a9869@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The scan request processing populated the direct SSIDs
in the FW scan request command also for 6GHz scan, which is not
needed and might result in unexpected behavior.
Fix the code to add the direct SSIDs only in case the scan
is not a 6GHz scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.f465937c7bbf.Ic11a1659ddda850c3ec1b1afbe9e2b9577ac1800@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the firmware crashes while we're waiting for the reset
handshake then it cannot possibly make progress anymore,
and we will just time out the wait. That's pointless, so
just stop waiting at that point.
Additionally, if it never acknowledges the reset handshake,
something went wrong.
Dump an error in both of these cases, but we need to do it
synchronously here since the device will be turned off.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.8b6a33544b4b.I55f97f70f8efa64db064a9207177a094c60ac8f1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When switching op-modes, or more generally when reconfiguring,
we might switch the RB size. In _iwl_pcie_rx_init() we have a
comment saying we must free all RBs since we might switch the
size, but this is actually too late: the switch has been done
and we'll free the buffers with the wrong size.
Fix this by always freeing the buffers, if any, at the start
of configure, instead of only after the size may have changed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.42d7c93279c4.I07f74e65aab0e3d965a81206fcb289dc92d74878@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On 64-bit machines, struct iwl_rx_mem_buffer has a lot of
padding due to the use of pointers after the small items.
Move the list entry before them, and while at it also add
documentation for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.6a62255b3df0.I47bb36530a3c2cdbd73454c796ce608ee2a32a6c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the firmware crashes while we're already shutting down
the system, there isn't much we can do since the shutdown
process is continuing and we wanted to do that. Don't do
a FW restart, with the implied debug collection, in this
case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.43a7351ae6bd.I164d48ce4379accf76ea0637983fd946d52dc6f5@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
First set of patches for v5.15. This got delayed as I have been mostly
offline for the last few weeks. The biggest change is removal of
prism54 driver, otherwise just smaller changes.
Major changes:
ath5k, ath9k, ath10k, ath11k:
* switch from 'pci_' to 'dma_' API
brcmfmac
* allow per-board firmware binaries
* add support 43752 SDIO device
prism54
* remove the obsoleted driver, everyone should be using p54 driver instead
-----BEGIN PGP SIGNATURE-----
iQFJBAABCgAzFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmEiEGcVHGt2YWxvQGNv
ZGVhdXJvcmEub3JnAAoJEG4XJFUm622b0UoH+wT2LyZ92PZUxL5FwUl1kFIRKefw
8H5urbnlioiqFjKU9YAwD3bvGTrIPMGjOkR50JxPNxxKzcx5CgHz6GQmIe16aSs2
FEMV//G5dcGe7HS94kdOiBhm6EqLrr+hrqWRop+uEnu9DuQNxnS/5ZpxU6zNSK7z
S2u2m/zpcaE6/F+Po1jlGyPRzUbTR8xV/3a7LKUgbZslbrGKayn+3aQwFXZ4D8YX
OhGrsL5nbFjKP0Ys7X/QS9s31IuzMBO5IUVMyJzcY7p6pPPFspxiGaT+HqUixZ9G
eb0hStxXANDAQbhBgz2KpIGH8J/0g8WdUwUj4SuiHOrhPSga6HZ06MhJ5xk=
=djwO
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.15
First set of patches for v5.15. This got delayed as I have been mostly
offline for the last few weeks. The biggest change is removal of
prism54 driver, otherwise just smaller changes.
Major changes:
ath5k, ath9k, ath10k, ath11k:
* switch from 'pci_' to 'dma_' API
brcmfmac
* allow per-board firmware binaries
* add support 43752 SDIO device
prism54
* remove the obsoleted driver, everyone should be using p54 driver instead
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the array addr on the stack but instead it
static const. Makes the object code smaller by 79 bytes:
Before:
text data bss dec hex filename
176015 54652 128 230795 3858b .../broadcom/brcm80211/brcmsmac/main.o
After:
text data bss dec hex filename
175872 54716 128 230716 3853c .../broadcom/brcm80211/brcmsmac/main.o
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210819125552.8888-1-colin.king@canonical.com
The rtw_pci_init_rx_ring function is only ever called with a fixed
constant or RTK_MAX_RX_DESC_NUM for the "len" argument. Since this
constant is defined as 512, the "if (len > TRX_BD_IDX_MASK)" check
can never happen (TRX_BD_IDX_MASK is defined as GENMASK(11, 0) or in
other words as 4095).
So, remove this check.
The true motivation for this patch is to silence a false Coverity
warning.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210731163546.10753-1-len.baker@gmx.com
Current flow will lead to null ptr access because of trying
to get the size of freed probe-request packets. We store the
information of packet size into rsvd page instead and also fix
the size error issue, which will cause unstable behavoir of
sending probe request by wow firmware.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-6-pkshih@realtek.com
After waking up from WoWLAN, call ieee80211_report_wowlan_wakeup
function call to report wakeup reason to userspace via nl80211.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-5-pkshih@realtek.com
The kernel test robot reports undefined reference after we report wakeup
reason to mac80211. This is because CONFIG_PM is not defined in the testing
configuration file. In fact, functions within wow.c are used if CONFIG_PM
is defined, so use CONFIG_PM to decide whether we build this file or not.
The reported messages are:
hppa-linux-ld: drivers/net/wireless/realtek/rtw88/wow.o: in function `rtw_wow_show_wakeup_reason':
>> (.text+0x6c4): undefined reference to `ieee80211_report_wowlan_wakeup'
>> hppa-linux-ld: (.text+0x6e0): undefined reference to `ieee80211_report_wowlan_wakeup'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-4-pkshih@realtek.com
The original setting of rsvd pages is compilcated and lead to
error for connecting to AP after resuming from pno mode.
We refine the setting based on different firmware and the link state
to avoid it.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-3-pkshih@realtek.com
In current wow flow, driver calls rtw_wow_fw_start and sleep for 100ms,
to wait firmware finish preliminary work and then update the value of
WOWLAN_WAKE_REASON register to zero. But later firmware will start wow
function with power-saving mode, in which mode the value of
WOWLAN_WAKE_REASON register is 0xea. So driver may get 0xea value and
return fail. We use read_poll_timeout instead to check the value to avoid
this issue.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-2-pkshih@realtek.com
We find the power sequence of system suspend flow don't meet
the criteria when using 8822CE-VR chip by rfe-type 6, because the
reference clock form host is sometimes late. To avoid the behavoir,
we keep CLKREQ# signal to low during suspend to make sure the reference
clock arrival in time.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210727100503.31626-1-pkshih@realtek.com
Finetune parameter for firmware.
Previous mode neglects environment impacts and could lead to
performance downgrade in some cases.
This new mode makes fw adapts better under noisy environment.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210713104524.47101-3-pkshih@realtek.com
Enabling this improves tx performance for long distance transmission.
We used to enable stbc by the rx stbc cap of the associated station.
But rx cap will be masked out in ieee80211_ht_cap_ie_to_sta_ht_cap
if we do not declare tx stbc.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210713104524.47101-2-pkshih@realtek.com
We find that some disconnect events are related to failure of
tx report, so increase log level to improve debuggability.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210713104524.47101-1-pkshih@realtek.com
The TX A-MPDU aggregation is not handled in the driver since the
ieee80211_start_tx_ba_session has never been started properly.
Start and stop the TX BA session by tracking the TX aggregation
status of each TID. Fix the ampdu_action and the tx descriptor
accordingly with the given TID.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804151325.86600-1-chris.chiu@canonical.com
There will be crazy numbers of interrupts triggered by 8188cu and
8192cu module, around 8000~10000 interrupts per second, on the usb
host controller. Compare with the vendor driver source code, it's
mapping to the configuration CONFIG_USB_INTERRUPT_IN_PIPE and it is
disabled by default.
Since the interrupt transfer is neither used for TX/RX nor H2C
commands. Disable it to avoid the excessive amount of interrupts
for the 8188cu and 8192cu module which I only have for verification.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Tested-by: reto.schneider@husqvarnagroup.com
Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210701163354.118403-1-chris.chiu@canonical.com
Don't populate the arrays wpa_oui and wps_oui on the stack but
instead them static const. Makes the object code smaller by 63 bytes:
Before:
text data bss dec hex filename
29453 5451 64 34968 8898 .../wireless/marvell/mwifiex/sta_ioctl.o
After:
text data bss dec hex filename
29356 5611 64 35031 88d7 ../wireless/marvell/mwifiex/sta_ioctl.o
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210819121651.7566-1-colin.king@canonical.com
There is no case in which the variable cmd_node->cmd_skb has no ->data,
and thus the variable host_cmd is guaranteed to be not NULL. Therefore,
the null-pointer check is redundant and can be dropped.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804020305.29812-1-islituo@gmail.com
Use goto labels on error path for probe functions. This makes code easier
to read. With this introduce also netdev_cleanup and call it where
necessary.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210806081229.721731-2-claudiu.beznea@microchip.com
Don't populate arrays the stack but instead make them static const. Replace
array channel_info with channel_all since it contains the same data as
channel_all. Makes object code smaller by 961 bytes.
Before:
text data bss dec hex filename
128147 44250 1024 173421 2a56d ../realtek/rtlwifi/rtl8192de/phy.o
After
text data bss dec hex filename
127122 44314 1024 172460 2a1ac ../realtek/rtlwifi/rtl8192de/phy.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210803144949.79433-2-colin.king@canonical.com
The variables rtstatus and place are being initialized with a values
that are never read, the initializations are redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210803144949.79433-1-colin.king@canonical.com
Return -ENODEV instead of success for unsupported devices.
Fixes: 54fdb318c1 ("rsi: add new device model for 9116")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210816183947.GA2119@kili
This code returns success if the kmemdup() fails, but obviously it
should return -ENOMEM instead.
Fixes: e5a1ecc97e ("rsi: add firmware loading for 9116 device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210805103746.GA26417@kili
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
Split memcpy() for each address range to help memcpy() correctly reason
about the bounds checking. Avoids the future warning:
In function 'fortify_memcpy_chk',
inlined from 'memcpy_toio' at ./include/asm-generic/io.h:1204:2,
inlined from 'ray_build_header.constprop' at drivers/net/wireless/ray_cs.c:984:3:
./include/linux/fortify-string.h:285:4: warning: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Wattribute-warning]
285 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210819202825.3545692-4-keescook@chromium.org
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
libipw_read_qos_param_element() copies a struct libipw_info_element
into a struct libipw_qos_information_element, but is actually wanting to
copy into the larger struct libipw_qos_parameter_info (the contents of
ac_params_record[] is later examined). Refactor the routine to perform
centralized checks, and copy the entire contents directly (since the id
and len members match the elementID and length members):
struct libipw_info_element {
u8 id;
u8 len;
u8 data[];
} __packed;
struct libipw_qos_information_element {
u8 elementID;
u8 length;
u8 qui[QOS_OUI_LEN];
u8 qui_type;
u8 qui_subtype;
u8 version;
u8 ac_info;
} __packed;
struct libipw_qos_parameter_info {
struct libipw_qos_information_element info_element;
u8 reserved;
struct libipw_qos_ac_parameter ac_params_record[QOS_QUEUE_NUM];
} __packed;
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210819202825.3545692-2-keescook@chromium.org
Dynamic size calculations (especially multiplication) should not be
performed in memory allocator function arguments due to the risk of them
overflowing. This could lead to values wrapping around and a smaller
allocation being made than the caller was expecting. Using those
allocations could lead to linear overflows of heap memory and other
misbehaviors.
To avoid this scenario, use the struct_size helper.
Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210717142513.5411-1-len.baker@gmx.com
Add HW and SDIO ids for use with the SparkLan AP6275S
Add the firmware mapping structures for the BRCM43752 chipset.
The 43752 needs some things setup similar to the 43012 chipset.
The WATERMARK shows better performance when initialized to the 4373 value.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210812165218.2508258-2-angus@akkea.ca
This puts tasks submitted to the SDIO workqueue at the head of the queue
and runs them immediately. This gets higher RX throughput with the SDIO
bus.
This was originally submitted as [1]. The original author Wright Feng
reports
> throughput result with 43455(11ac) on 1 core 1.6 Ghz platform is
> Without WQ_HIGGPRI TX/RX: 293/301 (mbps)
> With WQ_HIGHPRI TX/RX: 293/321 (mbps)
I tested this with a 43364(11bgn) on a 1 core 800 MHz platform and got
Without WQ_HIGHPRI TX/RX: 16/19 (Mbits/sec)
With WQ_HIGHPRI TX/RX: 24/20 (MBits/sec)
[1] https://lore.kernel.org/linux-wireless/1584604406-15452-4-git-send-email-wright.feng@cypress.com/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Arend van Spriel <aspriel@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210802170904.3116223-1-sean.anderson@seco.com
A separate firmware is needed for Broadcom 43430 revision 2. This
chip can be found in e.g. certain revisions of Ampak AP6212 wireless
IC. Original firmware file from IC vendor is named
'fw_bcm43436b0.bin', but brcmfmac and also btbcm drivers report chip
id 43430, so requested firmware file name is
'brcmfmac43430b0-sdio.bin' in line with other 43430 revisions.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804231308.576071-1-mike.rudenko@gmail.com
Historically the broadcom wifi chipsets always had enumeration
space containing all core information at same place. However, for
new chipsets the ASIC developers moved away from that given fact.
So we have to accommodate that it can differ per chipset.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1627505434-9544-5-git-send-email-arend.vanspriel@broadcom.com
