Remove unnecessary of_node_put from the continue path to prevent
child node from being released twice, which could avoid resource
leak or other unexpected issues.
Signed-off-by: Lu Hongfei <luhongfei@vivo.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Fixes: de879a016a ("net: dsa: felix: add functionality when not all ports are supported")
Link: https://lore.kernel.org/r/20230710031859.36784-1-luhongfei@vivo.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This switch implements Hold/Release in a strange way, with no control
from the user as required by IEEE 802.1Q-2018 through Set-And-Hold-MAC
and Set-And-Release-MAC, but rather, it emits HOLD requests implicitly
based on the schedule.
Namely, when the gate of a preemptible TC is about to close (actually
QSYS::PREEMPTION_CFG.HOLD_ADVANCE octet times in advance of this event),
the QSYS seems to emit a HOLD request pulse towards the MAC which
preempts the currently transmitted packet, and further packets are held
back in the queue system.
This allows large frames to be squeezed through small time slots,
because HOLD requests initiated by the gate events result in the frame
being segmented in multiple fragments, the bit time of which is equal to
the size of the time slot.
It has been reported that the vsc9959_tas_guard_bands_update() logic
breaks this, because it doesn't take preemptible TCs into account, and
enables oversized frame dropping when the time slot doesn't allow a full
MTU to be sent, but it does allow 2*minFragSize to be sent (128B).
Packets larger than 128B are dropped instead of being sent in multiple
fragments.
Confusingly, the manual says:
| For guard band, SDU calculation of a traffic class of a port, if
| preemption is enabled (through 'QSYS::PREEMPTION_CFG.P_QUEUES') then
| QSYS::PREEMPTION_CFG.HOLD_ADVANCE is used, otherwise
| QSYS::QMAXSDU_CFG_*.QMAXSDU_* is used.
but this only refers to the static guard band durations, and the
QMAXSDU_CFG_* registers have dual purpose - the other being oversized
frame dropping, which takes place irrespective of whether frames are
preemptible or express.
So, to fix the problem, we need to call vsc9959_tas_guard_bands_update()
from ocelot_port_update_active_preemptible_tcs(), and modify the guard
band logic to consider a different (lower) oversize limit for
preemptible traffic classes.
Fixes: 403ffc2c34 ("net: mscc: ocelot: add support for preemptible traffic classes")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-ID: <20230705104422.49025-4-vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future change we will need to make
ocelot_port_update_active_preemptible_tcs() call
vsc9959_tas_guard_bands_update(), but that is currently not possible,
since the ocelot switch lib does not have access to functions private to
the DSA wrapper.
Move the pointer to vsc9959_tas_guard_bands_update() from felix->info
(which is private to the DSA driver) to ocelot->ops (which is also
visible to the ocelot switch lib).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-ID: <20230705104422.49025-3-vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future commit we will have to call vsc9959_tas_guard_bands_update()
from ocelot_port_update_active_preemptible_tcs(), and that will be
impossible due to the AB/BA locking dependencies between
ocelot->tas_lock and ocelot->fwd_domain_lock.
Just like we did in commit 3ff468ef98 ("net: mscc: ocelot: remove
struct ocelot_mm_state :: lock"), the only solution is to expand the
scope of ocelot->fwd_domain_lock for it to also serialize changes made
to the Time-Aware Shaper, because those will have to result in a
recalculation of cut-through TCs, which is something that depends on the
forwarding domain.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-ID: <20230705104422.49025-2-vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver implements a workaround for the fact that it doesn't have an
IRQ source to tell it whether PTP frames are available through the
extraction registers, for those frames to be processed and passed
towards the network stack. That workaround is to configure the switch,
through felix_hwtstamp_set() -> felix_update_trapping_destinations(),
to create two copies of PTP packets: one sent over Ethernet to the DSA
master, and one to be consumed through the aforementioned CPU extraction
queue registers.
The reason why we want PTP packets to be consumed through the CPU
extraction registers in the first place is because we want to see their
hardware RX timestamp. With tag_8021q, that is only visible that way,
and it isn't visible with the copy of the packet that's transmitted over
Ethernet.
The problem with the workaround implementation is that it drops the
packet received over Ethernet, in expectation of its copy being present
in the CPU extraction registers. However, if felix_hwtstamp_set() hasn't
run (aka PTP RX timestamping is disabled), the driver will drop the
original PTP frame and there will be no copy of it in the CPU extraction
registers. So, the network stack will simply not see any PTP frame.
Look at the port's trapping configuration to see whether the driver has
previously enabled the CPU extraction registers. If it hasn't, just
don't RX timestamp the frame and let it be passed up the stack by DSA,
which is perfectly fine.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The DEV_MAC_MAXLEN_CFG register contains a 16-bit value - up to 65535.
Plus 2 * VLAN_HLEN (4), that is up to 65543.
The picos_per_byte variable is the largest when "speed" is lowest -
SPEED_10 = 10. In that case it is (1000000L * 8) / 10 = 800000.
Their product - 52434400000 - exceeds 32 bits, which is a problem,
because apparently, a multiplication between two 32-bit factors is
evaluated as 32-bit before being assigned to a 64-bit variable.
In fact it's a problem for any MTU value larger than 5368.
Cast one of the factors of the multiplication to u64 to force the
multiplication to take place on 64 bits.
Issue found by Coverity.
Fixes: 55a515b1f5 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230613170907.2413559-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This error path needs call mutex_unlock(&ocelot->tas_lock) before
returning.
Fixes: 2d800bc500 ("net/sched: taprio: replace tc_taprio_qopt_offload :: enable with a "cmd" enum")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inspired from struct flow_cls_offload :: cmd, in order for taprio to be
able to report statistics (which is future work), it seems that we need
to drill one step further with the ndo_setup_tc(TC_SETUP_QDISC_TAPRIO)
multiplexing, and pass the command as part of the common portion of the
muxed structure.
Since we already have an "enable" variable in tc_taprio_qopt_offload,
refactor all drivers to check for "cmd" instead of "enable", and reject
every other command except "replace" and "destroy" - to be future proof.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> # for lan966x
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the newly introduced lynx_pcs_create_mdiodev() which simplifies the
creation and destruction of the lynx PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to not transmit (preemptible) frames which will be received by
the link partner as corrupted (because it doesn't support FP), the
hardware requires the driver to program the QSYS_PREEMPTION_CFG_P_QUEUES
register only after the MAC Merge layer becomes active (verification
succeeds, or was disabled).
There are some cases when FP is known (through experimentation) to be
broken. Give priority to FP over cut-through switching, and disable FP
for known broken link modes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mqprio queue configuration can appear either through
TC_SETUP_QDISC_MQPRIO or through TC_SETUP_QDISC_TAPRIO. Make sure both
are treated in the same way.
Code does nothing new for now (except for rejecting multiple TXQs per
TC, which is a useless concept with DSA switches).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This doesn't apply anything to hardware and in general doesn't do
anything that the software variant doesn't do, except for checking that
there isn't more than 1 TXQ per TC (TXQs for a DSA switch are a dubious
concept anyway). The reason we add this is to be able to parse one more
field added to struct tc_mqprio_qopt_offload, namely preemptible_tcs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the switch emits an IRQ, we don't know what caused it, and we
iterate through all ports to check the MAC Merge status.
Move that iteration inside the ocelot lib; we will change the locking in
a future change and it would be good to encapsulate that lock completely
within the ocelot lib.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
That comment was written prior to knowing that what I was actually
seeing was a manifestation of the bug fixed in commit b4024c9e5c
("felix: Fix initialization of ioremap resources").
There isn't any particular reason now why the hardware initialization is
done in felix_setup(), so just delete that comment to avoid spreading
misinformation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VSC7512 has four ports with internal phys that are already supported.
There are additional ports that can be configured to work with external
phys.
Add support for these additional ethernet ports.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ports for Ocelot devices (VSC7511, VSC7512, VSC7513 and VSC7514) support
external phys. When external phys are used, additional configuration on
each port is required to enable QSGMII mode and set external phy modes.
Add a configurable hook into these routines, so the external ports can be
used.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a user of the Felix driver has a port running in SGMII / QSGMII mode, it
will need to utilize phylink_mac_config(). Add this configurability.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC7512 and VSC7514 have internal PLLs that can be used to control
different peripherals. Initialize these high speed I/O (HSIO) PLLs when
they exist, so that dependent peripherals like QSGMII can function.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/net/dsa/ocelot/ocelot_ext.c:143:34: error: ‘ocelot_ext_switch_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/net/dsa/ocelot/seville_vsc9953.c:1070:34: error: ‘seville_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During review of ocelot_ext, it created a private phylink instance
that wasn't necessary. This was removed for subsequent postings,
but the include file seems to have been left behind. Remove it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compiling a kernel which has both CONFIG_NET_DSA_MSCC_OCELOT_EXT
and CONFIG_MSCC_OCELOT_SWITCH enabled, the following error message will
be printed:
[ 5.266588] Error: Driver 'ocelot-switch' is already registered, aborting...
Rename the ocelot_ext.c driver to "ocelot-ext-switch" to avoid the name
duplication, and update the mfd_cell entry for its resources.
Fixes: 3d7316ac81 ("net: dsa: ocelot: add external ocelot switch control")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit did not properly convert the resource start/end format
into the DEFINE_RES_MEM_NAMED() start/length format, resulting in a
resource for vsc9959_imdio_res which is much longer than expected:
$ cat /proc/iomem
1f8000000-1f815ffff : pcie@1f0000000
1f8140000-1f815ffff : 0000:00:00.5
1f8148030-1f815006f : imdio
vs (correct)
$ cat /proc/iomem
1f8000000-1f815ffff : pcie@1f0000000
1f8140000-1f815ffff : 0000:00:00.5
1f8148030-1f814803f : imdio
Luckily it's not big enough to exceed the size of the parent resource
(pci_resource_end(pdev, VSC9959_IMDIO_PCI_BAR)), and it doesn't overlap
with anything else that the Linux driver uses currently, so the larger
than expected size isn't a practical problem that I can see. Although it
is clearly wrong in the /proc/iomem output.
Fixes: 044d447a80 ("net: dsa: felix: use DEFINE_RES_MEM_NAMED for resources")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the refactoring in the commit below, vsc9953_mdio_read() was
replaced with mscc_miim_read(), which has one extra step: it checks for
the MSCC_MIIM_DATA_ERROR bits before returning the result.
On T1040RDB, there are 8 QSGMII PCSes belonging to the switch, and they
are organized in 2 groups. First group responds to MDIO addresses 4-7
because QSGMIIACR1[MDEV_PORT] is 1, and the second group responds to
MDIO addresses 8-11 because QSGMIIBCR1[MDEV_PORT] is 2. I have double
checked that these values are correctly set in the SERDES, as well as
PCCR1[QSGMA_CFG] and PCCR1[QSGMB_CFG] are both 0b01.
mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 4 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 4 reg 0x5 MIIM_DATA 0x3da01, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR
As can be seen, the data in MIIM_DATA is still valid despite having the
MSCC_MIIM_DATA_ERROR bits set. The driver as introduced in commit
84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953
switch") was ignoring these bits, perhaps deliberately (although
unbeknownst to me).
This is an old IP and the hardware team cannot seem to be able to help
me track down a plausible reason for these failures. I'll keep
investigating, but in the meantime, this is a direct regression which
must be restored to a working state.
The only thing I can do is keep ignoring the errors as before.
Fixes: b996584523 ("net: dsa: ocelot: felix: utilize shared mscc-miim driver for indirect MDIO access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new user of MSCC_OCELOT_SWITCH_LIB was added, bringing back an old
link failure that was fixed with e5f3155267 ("ethernet: fix
PTP_1588_CLOCK dependencies"):
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_ptp_enable':
ocelot_ptp.c:(.text+0x8ee): undefined reference to `ptp_find_pin'
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_get_ts_info':
ocelot_ptp.c:(.text+0xd5d): undefined reference to `ptp_clock_index'
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_init_timestamp':
ocelot_ptp.c:(.text+0x15ca): undefined reference to `ptp_clock_register'
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_deinit_timestamp':
ocelot_ptp.c:(.text+0x16b7): undefined reference to `ptp_clock_unregister'
Add the same PTP dependency here, as well as in the MSCC_OCELOT_SWITCH_LIB
symbol itself to make it more obvious what is going on when the next
driver selects it.
Fixes: 3d7316ac81 ("net: dsa: ocelot: add external ocelot switch control")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20230209124435.1317781-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add control of an external VSC7512 chip.
Currently the four copper phy ports are fully functional. Communication to
external phys is also functional, but the SGMII / QSGMII interfaces are
currently non-functional.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the Felix driver would probe the ports and verify functionality, it
would fail if it hit single port mode that wasn't supported by the driver.
The initial case for the VSC7512 driver will have physical ports that
exist, but aren't supported by the driver implementation. Add the
OCELOT_PORT_MODE_NONE macro to handle this scenario, and allow the Felix
driver to continue with all the ports that are currently functional.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The architecture around the VSC7512 differs from existing felix drivers. In
order to add support for all the chip's features (pinctrl, MDIO, gpio) the
device had to be laid out as a multi-function device (MFD).
One difference between an MFD and a standard platform device is that the
regmaps are allocated to the parent device before the child devices are
probed. As such, there is no need for felix to initialize new regmaps in
these configurations, they can simply be requested from the parent device.
Add support for MFD configurations by performing this request from the
parent device.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The define FELIX_MAC_QUIRKS was used directly in the felix.c shared driver.
Other devices (VSC7512 for example) don't require the same quirks, so they
need to be configured on a per-device basis.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The build system currently complains:
scripts/Makefile.build:252: drivers/net/dsa/ocelot/Makefile:
felix.o is added to multiple modules: mscc_felix mscc_seville
Since felix.c holds the DSA glue layer, create a mscc_felix_dsa_lib.ko.
This is similar to how mscc_ocelot_switch_lib.ko holds a library for
configuring the hardware.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20230125145716.271355-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Felix (VSC9959) has a DEV_GMII:MM_CONFIG block composed of 2 registers
(ENABLE_CONFIG and VERIF_CONFIG). Because the MAC Merge statistics and
pMAC statistics are already in the Ocelot switch lib even if just Felix
supports them, I'm adding support for the whole MAC Merge layer in the
common Ocelot library too.
There is an interrupt (shared with the PTP interrupt) which signals
changes to the MM verification state. This is done because the
preemptible traffic classes should be committed to hardware only once
the verification procedure has declared the link partner of being
capable of receiving preemptible frames.
We implement ethtool getters and setters for the MAC Merge layer state.
The "TX enabled" and "verify status" are taken from the IRQ handler,
using a mutex to ensure serialized access.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix VSC9959 switch supports frame preemption and has a MAC Merge
layer. In addition to the structured stats that exist for the eMAC,
export the counters associated with its pMAC (pause, RMON, MAC, PHY,
control) plus the high-level MAC Merge layer stats. The unstructured
ethtool counters, as well as the rtnl_link_stats64 were left to report
only the eMAC counters.
Because statistics processing is quite self-contained in ocelot_stats.c
now, I've opted for introducing an ocelot->mm_supported bool, based on
which the common switch lib does everything, rather than pushing the
TSN-specific code in felix_vsc9959.c, as happens for other TSN stuff.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enetc MDIO bus driver can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new API calls where appropriate.
This driver is shared with the Felix DSA switch, so update that at the
same time.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ever since commit 4d1d157fb6 ("net: mscc: ocelot: share the common stat
definitions between all drivers") the stats_layout entry in ocelot and
felix drivers have become redundant. Remove the unnecessary code.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Drop the custom implementation of phylink_validate() in favor of the
generic one, which requires config->mac_capabilities to be set.
This was used up until now because of the possibility of being paired
with Aquantia PHYs with support for rate matching. The phylink framework
gained generic support for these, and knows to advertise all 10/100/1000
lower speed link modes when our SERDES protocol is 2500base-x
(fixed speed).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Our current vsc9959_tas_guard_bands_update() algorithm has a limitation
imposed by the hardware design. To avoid packet overruns between one
gate interval and the next (which would add jitter for scheduled traffic
in the next gate), we configure the switch to use guard bands. These are
as large as the largest packet which is possible to be transmitted.
The problem is that at tc-taprio intervals of sizes comparable to a
guard band, there isn't an obvious place in which to split the interval
between the useful portion (for scheduling) and the guard band portion
(where scheduling is blocked).
For example, a 10 us interval at 1Gbps allows 1225 octets to be
transmitted. We currently split the interval between the bare minimum of
33 ns useful time (required to schedule a single packet) and the rest as
guard band.
But 33 ns of useful scheduling time will only allow a single packet to
be sent, be that packet 1200 octets in size, or 60 octets in size. It is
impossible to send 2 60 octets frames in the 10 us window. Except that
if we reduced the guard band (and therefore the maximum allowable SDU
size) to 5 us, the useful time for scheduling is now also 5 us, so more
packets could be scheduled.
The hardware inflexibility of not scheduling according to individual
packet lengths must unfortunately propagate to the user, who needs to
tune the queueMaxSDU values if he wants to fit more small packets into a
10 us interval, rather than one large packet.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Existing felix DSA drivers (vsc9959, vsc9953) are all switches that were
integrated in NXP SoCs, which makes them a bit unusual compared to the
usual Microchip branded Ocelot switches.
To be precise, looking at
Documentation/devicetree/bindings/net/mscc,vsc7514-switch.yaml, one can
see 21 memory regions for the "switch" node, and these correspond to the
"targets" of the switch IP, which are spread throughout the guts of that
SoC's memory space.
In NXP integrations, those targets still exist, but they were condensed
within a single memory region, with no other peripheral in between them,
so it made more sense for the driver to ioremap the entire memory space
of the switch, and then find the targets within that memory space via
some offsets hardcoded in the driver.
The effect of this design decision is that now, the felix driver expects
hardware instantiations to provide their own resource definitions, which
is kind of odd when considering a typical device (those are retrieved
from 'reg' properties in the device tree, using platform_get_resource()
or similar).
Allow other hardware instantiations that share the felix driver to not
provide a hardcoded array of resources in the future. Instead, make the
common denominator based on which regmaps are created be just the
resource "names". Each instantiation comes with its own array of names
that are mandatory for it, and with an optional array of resources.
So we split the resources in 2 arrays, one is what's requested and the
other is what's provided. There is one pool of provided resources, in
felix->info->resources (of length felix->info->num_resources). There are
2 different ways of requesting a resource. One is by enum ocelot_target
(this handles the global regmaps), and one is by int port (this handles
the per-port ones).
For the existing vsc9959 and vsc9953, it would be a bit stupid to
request something that's not provided, given that the 2 arrays are both
defined in the same place.
The advantage is that we can now modify felix_request_regmap_by_name()
to make felix->info->resources[] optional, and if absent, the
implementation can call dev_get_regmap() and this is something that is
compatible with MFD.
Co-developed-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use less verbose resource definitions in vsc9959 and vsc9953. This also
sets IORESOURCE_MEM in the constant array of resources, so we don't have
to do this from felix_init_structs() - in fact, in the future, we may
even support IORESOURCE_REG resources.
Note that this macro takes start and length as argument, and we had
start and end before. So transform end into length.
While at it, sort the resources according to their offset.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It turns out that the idea of having a customizable implementation of a
regmap creation from a resource is not exactly useful. The idea was for
the new MFD-based VSC7512 driver to use something that creates a SPI
regmap from a resource. But there are problems in actually getting those
resources (it involves getting them from MFD).
To avoid all that, we'll be getting resources by name, so this custom
init_regmap() method won't be needed. Remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This address is only relevant for the vsc9959, which is a PCIe device
that holds its switch registers in a different PCIe BAR compared to the
registers for the internal MDIO controller.
Hide this aspect from the common felix driver and move the
pci_resource_start() call to the only place that needs it, which is in
vsc9959_mdio_bus_alloc().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The imdio_res is used only by vsc9959, which references its own
vsc9959_imdio_res through the common felix_info->imdio_res pointer.
Since the common code doesn't care about this resource (and it can't be
part of the common array of resources, either, because it belongs in a
different PCI BAR), just reference it directly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Changing the DSA master means different things depending on the tagging
protocol in use.
For NPI mode ("ocelot" and "seville"), there is a single port which can
be configured as NPI, but DSA only permits changing the CPU port
affinity of user ports one by one. So changing a user port to a
different NPI port globally changes what the NPI port is, and breaks the
user ports still using the old one.
To address this while still permitting the change of the NPI port,
require that the user ports which are still affine to the old NPI port
are down, and cannot be brought up until they are all affine to the same
NPI port.
The tag_8021q mode ("ocelot-8021q") is more flexible, in that each user
port can be freely assigned to one CPU port or to the other. This works
by filtering host addresses towards both tag_8021q CPU ports, and then
restricting the forwarding from a certain user port only to one of the
two tag_8021q CPU ports.
Additionally, the 2 tag_8021q CPU ports can be placed in a LAG. This
works by enabling forwarding via PGID_SRC from a certain user port
towards the logical port ID containing both tag_8021q CPU ports, but
then restricting forwarding per packet, via the LAG hash codes in
PGID_AGGR, to either one or the other.
When we change the DSA master to a LAG device, DSA guarantees us that
the LAG has at least one lower interface as a physical DSA master.
But DSA masters can come and go as lowers of that LAG, and
ds->ops->port_change_master() will not get called, because the DSA
master is still the same (the LAG). So we need to hook into the
ds->ops->port_lag_{join,leave} calls on the CPU ports and update the
logical port ID of the LAG that user ports are assigned to.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Drivers could refuse to offload a LAG configuration for a variety of
reasons, mainly having to do with its TX type. Additionally, since DSA
masters may now also be LAG interfaces, and this will translate into a
call to port_lag_join on the CPU ports, there may be extra restrictions
there. Propagate the netlink extack to this DSA method in order for
drivers to give a meaningful error message back to the user.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
All switch families supported by the ocelot lib (ocelot, felix, seville)
export the same registers so far. But for example felix also has TSN
counters, while the others don't.
To reduce the bloat even further, create an OCELOT_COMMON_STATS() macro
which just lists all stats that are common between switches. The array
elements are still replicated among all of vsc9959_stats_layout,
vsc9953_stats_layout and ocelot_stats_layout.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current definition of struct ocelot_stat_layout is long-winded (4
lines per entry, and we have hundreds of entries), so we could make an
effort to use the C preprocessor and reduce the line count.
Create an implicit correspondence between enum ocelot_reg, which tells
us the register address (SYS_COUNT_RX_OCTETS etc) and enum ocelot_stat
which allows us to index the ocelot->stats array (OCELOT_STAT_RX_OCTETS
etc), and don't require us to specify both when we define what stats
each switch family has.
Create an OCELOT_STAT() macro that pairs only an enum ocelot_stat to an
enum ocelot_reg, and an OCELOT_STAT_ETHTOOL() macro which also contains
a name exported to the unstructured ethtool -S stringset API. For now,
we define all counters as having the OCELOT_STAT_ETHTOOL() kind, but we
will add more counters in the future which are not exported to the
unstructured ethtool -S.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware counter is called C_TX_AGED, so rename SYS_COUNT_TX_AGING
to SYS_COUNT_TX_AGED. This will become important since we want to
minimize the way in which we declare struct ocelot_stat_layout elements,
using the C preprocessor.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA is integrated with the new standardized ethtool -S --groups option,
but the felix driver only exports unstructured statistics.
Reuse the array of 64-bit statistics collected by ocelot_check_stats_work(),
but just export select values from it.
Since ocelot_check_stats_work() runs periodically to avoid 32-bit
overflow, and the ethtool calling context is sleepable, we update the
64-bit stats one more time, to provide up-to-date values. The locking
scheme with a mutex followed by a spinlock is a bit hard to digest, so
we create and use a ocelot_port_stats_run() helper with a callback that
populates the ethool stats group the caller is interested in.
The exported stats are:
ethtool -S swp0 --groups eth-phy
ethtool -S swp0 --groups eth-mac
ethtool -S swp0 --groups eth-ctrl
ethtool -S swp0 --groups rmon
ethtool --include-statistics --show-pause swp0
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
