We need to set TE to "0" (i.e., disable serial transmission) to
get the expected behavior of the end of serial transmission.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-6-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the RZ/G2L users hardware manual (Rev.1.20 Sep, 2022), section
23.3.7 Serial Data Transmission (Asynchronous Mode), it is mentioned
that, set the SCR.TIE bit to 0 and SCR.TEIE bit to 1, after the last
data to be transmitted are written to the TDR.
This will generate tx end interrupt and in the handler set SCR.TE and
SCR.TEIE to 0.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-5-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the RZ/G2L users hardware manual (Rev.1.20 Sep, 2022), section
23.3.7 Serial Data Transmission (Asynchronous Mode) it is mentioned
that the TE (transmit enable) must be set after setting TIE (transmit
interrupt enable) or these 2 bits are set to 1 simultaneously by a
single instruction. So set these 2 bits in single instruction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-4-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA IP on RZ/G2L SoC has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked. Similarly clearing DMARS register makes signal to work as
interrupt signal and subsequent interrupt requests to the interrupt
controller are unmasked.
Add SCIFA DMA rx support for RZ/G2L alike SoCs by disabling RXI line
interrupt and setting DMARS registers by DMA api for DMA transfer request.
Apart from this, we must set FIFO trigger to 1 for the expected behavior
of the receive transmission.
While at it replace the parameter irq to s->irqs[SCIx_RXI_IRQ] in
disable_irq_nosync() to match enable_irq() in sci_dma_rx_reenable_irq().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA IP on RZ/G2L SoC has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked. Similarly clearing DMARS register makes signal to work as
interrupt signal and subsequent interrupt requests to the interrupt
controller are unmasked.
Add SCIFA DMA tx support for RZ/G2L alike SoCs by disabling TXI line
interrupt and setting DMARS registers by DMA api for DMA transfer request.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCI IP on RZ/G2L alike SoCs do not need regshift compared to other SCI
IPs on the SH platform. Currently, it does regshift and configuring Rx
wrongly. Drop adding regshift for RZ/G2L alike SoCs.
Fixes: dfc80387ae ("serial: sh-sci: Compute the regshift value for SCI ports")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230321114753.75038-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fourth interrupt on SCI port is transmit end interrupt compared to
the break interrupt on other port types. So, shuffle the interrupts to fix
the transmit end interrupt handler.
Fixes: e1d0be6161 ("sh-sci: Add h8300 SCI")
Cc: stable <stable@kernel.org>
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230317150403.154094-1-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The direction field in the DMA config is deprecated. The sh-sci driver
sets {src,dst}_{addr,addr_width} based on the DMA direction and
it results in dmaengine_slave_config() failure as RZ DMAC driver
validates {src,dst}_addr_width values independent of DMA direction.
Fix this issue by passing both {src,dst}_{addr,addr_width}
values independent of DMA direction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230322074717.6057-1-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/tty/serial/sh-sci.c:3144:34: error: ‘of_sci_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230310222957.315848-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230310144727.1545630-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "big" set of tty/serial driver changes for 6.2-rc1.
As in previous kernel releases, nothing big here at all, just some small
incremental serial/tty layer cleanups and some individual driver
additions and fixes. Highlights are:
- serial helper macros from Jiri Slaby to reduce the amount of
duplicated code in serial drivers
- api cleanups and consolidations from Ilpo Järvinen in lots of serial
drivers
- the usual set of n_gsm fixes from Daniel Starke as that code gets
exercised more
- TIOCSTI is finally able to be disabled if requested (security
hardening feature from Kees Cook)
- fsl_lpuart driver fixes and features added
- other small serial driver additions and fixes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wt5A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynSiACffLCC9SFnP1ClJJh73OpCN11alDAAoIfMct2A
/zrJ4on7o0YQU1Ilg2+k
=eD/I
-----END PGP SIGNATURE-----
Merge tag 'tty-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver changes for 6.2-rc1.
As in previous kernel releases, nothing big here at all, just some
small incremental serial/tty layer cleanups and some individual driver
additions and fixes. Highlights are:
- serial helper macros from Jiri Slaby to reduce the amount of
duplicated code in serial drivers
- api cleanups and consolidations from Ilpo Järvinen in lots of
serial drivers
- the usual set of n_gsm fixes from Daniel Starke as that code gets
exercised more
- TIOCSTI is finally able to be disabled if requested (security
hardening feature from Kees Cook)
- fsl_lpuart driver fixes and features added
- other small serial driver additions and fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (97 commits)
serial: atmel: don't stop the transmitter when doing PIO
serial: atmel: cleanup atmel_start+stop_tx()
tty: serial: fsl_lpuart: switch to new dmaengine_terminate_* API
serial: sunsab: Fix error handling in sunsab_init()
serial: altera_uart: fix locking in polling mode
serial: pch: Fix PCI device refcount leak in pch_request_dma()
tty: serial: fsl_lpuart: Use pm_ptr() to avoid need to make pm __maybe_unused
tty: serial: fsl_lpuart: Add runtime pm support
tty: serial: fsl_lpuart: enable wakeup source for lpuart
serdev: Replace poll loop by readx_poll_timeout() macro
tty: synclink_gt: unwind actions in error path of net device open
serial: stm32: move dma_request_chan() before clk_prepare_enable()
dt-bindings: serial: xlnx,opb-uartlite: Drop 'contains' from 'xlnx,use-parity'
serial: pl011: Do not clear RX FIFO & RX interrupt in unthrottle.
serial: amba-pl011: avoid SBSA UART accessing DMACR register
tty: serial: altera_jtaguart: remove struct altera_jtaguart
tty: serial: altera_jtaguart: use uart_port::read_status_mask
tty: serial: altera_jtaguart: remove unused altera_jtaguart::sigs
tty: serial: altera_jtaguart: remove flag from altera_jtaguart_rx_chars()
n_tty: Rename tail to old_tail in n_tty_read()
...
When setting up the early console, the setup() callback of the
regular console is used. It is called manually before registering
the early console instead of providing a setup() callback for the
early console. This is probably because the early setup needs a
different @options during the early stage.
The issue here is that the setup() callback is called without the
console_list_lock held and functions such as uart_set_options()
expect that.
Rather than manually calling the setup() function before registering,
provide an early console setup() callback that will use the different
early options. This ensures that the error checking, ordering, and
locking context when setting up the early console are correct.
Since this early console can only be registered via the earlyprintk=
parameter, the @options argument of the setup() callback will always
be NULL. Rather than simply ignoring the argument, add a WARN_ON()
to get our attention in case the setup() callback semantics should
change in the future.
Note that technically the current implementation works because it is
only used in early boot. And since the early console setup is
performed before registering, it cannot race with anything and thus
does not need any locking. However, longterm maintenance is easier
when drivers rely on the subsystem API rather than manually
implementing steps that could cause breakage in the future.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-41-john.ogness@linutronix.de
There is no need to and tail with UART_XMIT_SIZE - 1 because tail is
already on valid range.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220823141839.165244-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Testing also CIRC_CNT() with CIRC_CNT_TO_END() is unnecessary because
to latter alone covers all necessary cases.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220823141839.165244-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There should be no reason to adjust old ktermios which is going to get
discarded anyway.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816115739.10928-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only CS7 and CS8 seem supported but CSIZE is not sanitized from
CS5 or CS6 to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: 1da177e4c3 (Linux-2.6.12-rc2)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, uart_console_write->putchar's second parameter (the
character) is of type int. It makes little sense, provided uart_console_write()
accepts the input string as "const char *s" and passes its content -- the
characters -- to putchar(). So switch the character's type to unsigned
char.
We don't use char as that is signed on some platforms. That would cause
troubles for drivers which (implicitly) cast the char to u16 when
writing to the device. Sign extension would happen in that case and the
value written would be completely different to the provided char. DZ is
an example of such a driver -- on MIPS, it uses u16 for dz_out in
dz_console_putchar().
Note we do the char -> uchar conversion implicitly in
uart_console_write(). Provided we do not change size of the data type,
sign extension does not happen there, so the problem is void.
This makes the types consistent and unified with the rest of the uart
layer, which uses unsigned char in most places already. One exception is
xmit_buf, but that is going to be converted later.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@orcam.me.uk>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Karol Gugala <kgugala@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Taichi Sugaya <sugaya.taichi@socionext.com>
Cc: Takao Orito <orito.takao@socionext.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com> [atmel_serial]
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Neil Armstrong <narmstrong@baylibre.com> # meson_serial
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220303080831.21783-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the SCIF serial driver to remove printouts for break, frame, parity
and overrun errors. This reduces the amount of console printouts generated
by the defconfig kernel on R-Car Gen3 for certain use cases. To retrieve
more information about such errors the user may inspect counters. Also these
errors are fed into the TTY layer for further application specific handling.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Link: https://lore.kernel.org/r/163884254093.18109.2982470198301927679.sendpatchset@octo
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sh-sci driver supports up to four input clocks, of which only the
first one is mandatory.
Replace devm_clk_get() and custom error checking by
devm_clk_get_optional(), to simplify the code and to catch all real
errors.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/bce27288cb570952dd96b441e1af8768ad8b4870.1639663832.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1b463bd510 ("ARM: dts: r8a7794: Rename the serial
port clock to fck") in v4.6, all upstream DTS files call the SCIF
functional clock "fck".
Hence the time is ripe to drop backward-compatibility with old DTBs that
use the old "sci_ick" name.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b4103e44d6ac46b6c1c264e2aeac80b39941fe74.1639663832.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On RZ/G2L SoC we need to explicitly deassert the reset line
for the device to work, use this opportunity to deassert/assert
reset line in sh-sci driver.
This patch adds support to read the "resets" property (if available)
from DT and perform deassert/assert when required.
Also, propagate the error to the caller of sci_parse_dt() instead of
returning NULL in case of failure.
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110232920.19198-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes two issues that cause the sysrq sequence to be inadvertently
aborted on SCIF serial consoles:
- a NUL character remains in the RX queue after a break has been detected,
which is then passed on to uart_handle_sysrq_char()
- the break interrupt is handled twice on controllers with multiplexed ERI
and BRI interrupts
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210816162201.28801-1-uli+renesas@fpond.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the previous patch, we introduced tty_get_char_size() and
tty_get_frame_size() for computing character and frame sizes,
respectively. Here, we make use of them in various tty drivers where
applicable.
The stats look nice: 12 insertions, 169 deletions.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Oliver Neukum <oneukum@suse.com>
Acked-by: Alex Elder <elder@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop dmaengine transfer in sci_stop_tx(). Otherwise, the following
message is possible output when system enters suspend and while
transferring data, because clearing TIE bit in SCSCR is not able to
stop any dmaengine transfer.
sh-sci e6550000.serial: ttySC1: Unable to drain transmitter
Note that this driver has already used some #ifdef in the .c file
so that this patch also uses #ifdef to fix the issue. Otherwise,
build errors happens if the CONFIG_SERIAL_SH_SCI_DMA is disabled.
Fixes: 73a19e4c03 ("serial: sh-sci: Add DMA support.")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210610110806.277932-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serial support for RZ/G2L SoC with earlycon and
extended mode register support.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210603221758.10305-11-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Receive FIFO Data Count Trigger field (RTRG[6:0]) in the Receive
FIFO Data Count Trigger Register (HSRTRGR) of HSCIF can only hold values
ranging from 0-127. As the FIFO size is equal to 128 on HSCIF, the user
can write an out-of-range value, touching reserved bits.
Fix this by limiting the trigger value to the FIFO size minus one.
Reverse the order of the checks, to avoid rx_trig becoming zero if the
FIFO size is one.
Note that this change has no impact on other SCIF variants, as their
maximum supported trigger value is lower than the FIFO size anyway, and
the code below takes care of enforcing these limits.
Fixes: a380ed461f ("serial: sh-sci: implement FIFO threshold register setting")
Reported-by: Linh Phung <linh.phung.jy@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/5eff320aef92ffb33d00e57979fd3603bbb4a70f.1620648218.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the transition to hrtimers there is no more need to set a minimum
RX timeout to work around latency issues.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210415093547.21639-1-uli+renesas@fpond.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f38278e9b8.
There has been a quick fix against uninitialised lock revealed by
the commit f743061a85 ("serial: core: Initialise spin lock before use
in uart_configure_port()"). Since we have now better fix in serial core,
this may be safely reverted.
Fixes: f38278e9b8 ("serial: sh-sci: Initialize spinlock for uart console")
Depends-on: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200711135346.71171-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For SCIF and HSCIF interfaces the SCxSR register holds the status of
data that is to be read next from SCxRDR register, But where as for
SCIFA and SCIFB interfaces SCxSR register holds status of data that is
previously read from SCxRDR register.
This patch makes sure the status register is read depending on the port
types so that errors are caught accordingly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kazuhiro Fujita <kazuhiro.fujita.jg@renesas.com>
Signed-off-by: Hao Bui <hao.bui.yg@renesas.com>
Signed-off-by: KAZUMI HARADA <kazumi.harada.rh@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1585333048-31828-1-git-send-email-kazuhiro.fujita.jg@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFRBg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn2VACgkge7vTeUNeZFc+6F4NWphAQ5tCQAoK/MMbU6
0O8ef7PjFwCU4s227UTv
=6m40
-----END PGP SIGNATURE-----
Merge tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: n_hdlc: Use flexible-array member and struct_size() helper
tty: baudrate: SPARC supports few more baud rates
tty: baudrate: Synchronise baud_table[] and baud_bits[]
tty: serial: meson_uart: Add support for kernel debugger
serial: imx: fix a race condition in receive path
serial: 8250_bcm2835aux: Document struct bcm2835aux_data
serial: 8250_bcm2835aux: Use generic remapping code
serial: 8250_bcm2835aux: Allocate uart_8250_port on stack
serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Fix line mismatch on driver unbind
serial_core: Remove unused member in uart_port
vt: Correct comment documenting do_take_over_console()
vt: Delete comment referencing non-existent unbind_con_driver()
arch/xtensa/setup: Drop dummy_con initialization
arch/x86/setup: Drop dummy_con initialization
arch/unicore32/setup: Drop dummy_con initialization
arch/sparc/setup: Drop dummy_con initialization
arch/sh/setup: Drop dummy_con initialization
arch/s390/setup: Drop dummy_con initialization
...
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-42-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Old early platform device support is now sh-specific. Before moving on
to implementing new early platform framework based on real platform
devices, prefix all early platform symbols with 'sh_'.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/20191003092913.10731-3-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SuperH is the only user of the current implementation of early platform
device support. We want to introduce a more robust approach to early
probing. As the first step - move all the current early platform code
to arch/sh.
In order not to export internal drivers/base functions to arch code for
this temporary solution - copy the two needed routines for driver
matching from drivers/base/platform.c to arch/sh/drivers/platform_early.c.
Also: call early_platform_cleanup() from subsys_initcall() so that it's
called after all early devices are probed.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/20191003092913.10731-2-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As platform_get_irq() now prints an error when the interrupt does not
exist, scary warnings may be printed for optional interrupts:
sh-sci e6550000.serial: IRQ index 1 not found
sh-sci e6550000.serial: IRQ index 2 not found
sh-sci e6550000.serial: IRQ index 3 not found
sh-sci e6550000.serial: IRQ index 4 not found
sh-sci e6550000.serial: IRQ index 5 not found
Fix this by calling platform_get_irq_optional() instead for all but the
first interrupts, which are optional.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191001180743.1041-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1d267ea653 ("serial: mctrl-gpio: simplify init
routine"), mctrl_gpio_init() returns failure if the assignment to any
member of the gpio array results in an error pointer.
Since commit c359522194593815 ("serial: mctrl_gpio: Avoid probe failures
in case of missing gpiolib"), mctrl_gpio_to_gpiod() returns NULL in the
!CONFIG_GPIOLIB case.
Hence there is no longer a need to check for mctrl_gpio_to_gpiod()
returning an error value. A simple NULL check is sufficient.
This follows the spirit of commit 445df7ff3f ("serial: mctrl-gpio:
drop usages of IS_ERR_OR_NULL") in the mctrl-gpio core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190814092924.13857-4-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the mctrl_gpio code returns NULL instead of ERR_PTR(-ENOSYS)
if CONFIG_GPIOLIB is disabled, we can safely remove this check.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20190802100349.8659-3-frieder.schrempf@kontron.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While commit b6b996b6cd ("treewide: Use DEVICE_ATTR_RW") converted
the rx_fifo_timeout attribute, it forgot to convert rx_fifo_trigger due
to a slightly different function naming.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20190731124555.14349-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a driver, do not call "raw" sysfs functions, instead call driver
core ones. Specifically convert the use of sysfs_create_file() and
sysfs_remove_file() to use device_create_file() and device_remove_file()
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/20190704084617.3602-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the .flush_buffer() callback clears sci_port.tx_dma_len since
commit 1cf4a7efdc ("serial: sh-sci: Fix race condition causing
garbage during shutdown"), it does not terminate a transmit DMA
operation that may be in progress.
Fix this by terminating any pending DMA operations, and resetting the
corresponding cookie.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Link: https://lore.kernel.org/r/20190624123540.20629-3-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
