All of the OF code that is used has stubbed and will compile and link
just fine, keeping COMPILE_TEST is enough.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210106191546.1358324-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use existing rx processed count to track against budget, thereby making
budget decrement operation redundant.
rx_desc_count can be calculated outside the rx loop, making the loop a
bit smaller.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can increase the efficiency of rx path by using buffers to receive
packets then build SKBs around them just before passing into the network
stack. In contrast, preallocating SKBs too early reduces CPU cache
efficiency.
Check if we're in NAPI context when refilling RX. Normally we're almost
always running in NAPI context. Dispatch to napi_alloc_frag directly
instead of relying on netdev_alloc_frag which does the same but
with the overhead of local_bh_disable/enable.
Tested on BCM6328 320 MHz and iperf3 -M 512 to measure packet/sec
performance. Included netif_receive_skb_list and NET_IP_ALIGN
optimizations.
Before:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.00 sec 49.9 MBytes 41.9 Mbits/sec 197 sender
[ 4] 0.00-10.00 sec 49.3 MBytes 41.3 Mbits/sec receiver
After:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-30.00 sec 171 MBytes 47.8 Mbits/sec 272 sender
[ 4] 0.00-30.00 sec 170 MBytes 47.6 Mbits/sec receiver
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rx SKB ring use the same code for cleanup at various points.
Combine them into a function to reduce lines of code.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TQM rings are hardware resources that require host context memory
managed by the driver. The driver supports up to 9 TQM rings and
the number of rings to use is requested by firmware during run-time.
Cap this number to the maximum supported to prevent accessing beyond
the array. Future firmware may request more than 9 TQM rings. Define
macros to remove the magic number 9 from the C code.
Fixes: ac3158cb01 ("bnxt_en: Allocate TQM ring context memory according to fw specification.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A recent change skips sending firmware messages to the firmware when
pci_channel_offline() is true during fatal AER error. To make this
complete, we need to move the re-initialization sequence to
bnxt_io_resume(), otherwise the firmware messages to re-initialize
will all be skipped. In any case, it is more correct to re-initialize
in bnxt_io_resume().
Also, fix the reverse x-mas tree format when defining variables
in bnxt_io_slot_reset().
Fixes: b340dc680e ("bnxt_en: Avoid sending firmware messages when AER error is detected.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver is already allocating receive buffers of 2KiB and the
Ethernet MAC is configured to accept frames up to UMAC_MAX_MTU_SIZE.
Fixes: bfcb813203 ("net: dsa: configure the MTU for switch ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20201218173843.141046-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the 'register_netdev()' call fails, we must undo a previous
'bcmgenet_mii_init()' call.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201212182005.120437-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current scheme allocates a DMA buffer as big as the requested
firmware package file and DMAs the contents to firmware in one
operation. The buffer size can be several hundred kilo bytes and
the driver may not be able to allocate the memory. This will cause
firmware upgrade to fail.
Improve the scheme by using smaller DMA blocks and calling firmware to
DMA each block in a batch mode. Older firmware can cause excessive
NVRAM erases if the block size is too small so we try to allocate a
256K buffer to begin with and size it down successively if we cannot
allocate the memory.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In bnxt_flash_package_from_fw_obj(), if firmware returns the NO_SPACE
error, call __bnxt_flash_nvram() to create the UPDATE directory and
then loop back and retry one more time.
Since the first try may fail, we use the silent version to send the
firmware commands.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On NICs with a smaller NVRAM, FW installation may fail after multiple
updates due to fragmentation. The driver can retry when FW returns
a special error code. To faciliate the retry, we restructure the
logic that performs the flashing in a loop. The actual retry logic
will be added in the next patch.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This function will be modified in the next patch to retry flashing
the firmware in a loop. To facilate that, we rearrange the code so
that the steps that only need to be done once before the loop will be
moved to the top of the function.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor bnxt_flash_nvram() into __bnxt_flash_nvram() that takes an
additional dir_item_len parameter. The new function will be used
in subsequent patches with the dir_item_len parameter set to create
the UPDATE directory during flashing.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-12-03
The main changes are:
1) Support BTF in kernel modules, from Andrii.
2) Introduce preferred busy-polling, from Björn.
3) bpf_ima_inode_hash() and bpf_bprm_opts_set() helpers, from KP Singh.
4) Memcg-based memory accounting for bpf objects, from Roman.
5) Allow bpf_{s,g}etsockopt from cgroup bind{4,6} hooks, from Stanislav.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (118 commits)
selftests/bpf: Fix invalid use of strncat in test_sockmap
libbpf: Use memcpy instead of strncpy to please GCC
selftests/bpf: Add fentry/fexit/fmod_ret selftest for kernel module
selftests/bpf: Add tp_btf CO-RE reloc test for modules
libbpf: Support attachment of BPF tracing programs to kernel modules
libbpf: Factor out low-level BPF program loading helper
bpf: Allow to specify kernel module BTFs when attaching BPF programs
bpf: Remove hard-coded btf_vmlinux assumption from BPF verifier
selftests/bpf: Add CO-RE relocs selftest relying on kernel module BTF
selftests/bpf: Add support for marking sub-tests as skipped
selftests/bpf: Add bpf_testmod kernel module for testing
libbpf: Add kernel module BTF support for CO-RE relocations
libbpf: Refactor CO-RE relocs to not assume a single BTF object
libbpf: Add internal helper to load BTF data by FD
bpf: Keep module's btf_data_size intact after load
bpf: Fix bpf_put_raw_tracepoint()'s use of __module_address()
selftests/bpf: Add Userspace tests for TCP_WINDOW_CLAMP
bpf: Adds support for setting window clamp
samples/bpf: Fix spelling mistake "recieving" -> "receiving"
bpf: Fix cold build of test_progs-no_alu32
...
====================
Link: https://lore.kernel.org/r/20201204021936.85653-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The CNIC kconfig symbol selects UIO and UIO depends on MMU.
Since 'select' does not follow dependency chains, add the same MMU
dependency to CNIC.
Quietens this kconfig warning:
WARNING: unmet direct dependencies detected for UIO
Depends on [n]: MMU [=n]
Selected by [m]:
- CNIC [=m] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_BROADCOM [=y] && PCI [=y] && (IPV6 [=m] || IPV6 [=m]=n)
Fixes: adfc5217e9 ("broadcom: Move the Broadcom drivers")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Rasesh Mody <rmody@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Link: https://lore.kernel.org/r/20201129070843.3859-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add napi_id to the xdp_rxq_info structure, and make sure the XDP
socket pick up the napi_id in the Rx path. The napi_id is used to find
the corresponding NAPI structure for socket busy polling.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/bpf/20201130185205.196029-7-bjorn.topel@gmail.com
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
linux/netdevice.h is included in very many places, touching any
of its dependecies causes large incremental builds.
Drop the linux/ethtool.h include, linux/netdevice.h just needs
a forward declaration of struct ethtool_ops.
Fix all the places which made use of this implicit include.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20201120225052.1427503-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jump to init_err_release to cleanup. bnxt_unmap_bars() will also be
called but it will do nothing if the BARs are not mapped yet.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1605858271-8209-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Link: https://lore.kernel.org/r/1605792621-6268-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: c213eae8d3 ("bnxt_en: Improve VF/PF link change logic.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Link: https://lore.kernel.org/r/1605701851-20270-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When performing a flash update via devlink, device drivers may inform
user space of status updates via
devlink_flash_update_(begin|end|timeout|status)_notify functions.
It is expected that drivers do not send any status notifications unless
they send a begin and end message. If a driver sends a status
notification without sending the appropriate end notification upon
finishing (regardless of success or failure), the current implementation
of the devlink userspace program can get stuck endlessly waiting for the
end notification that will never come.
The current ice driver implementation may send such a status message
without the appropriate end notification in rare cases.
Fixing the ice driver is relatively simple: we just need to send the
begin_notify at the start of the function and always send an end_notify
no matter how the function exits.
Rather than assuming driver authors will always get this right in the
future, lets just fix the API so that it is not possible to get wrong.
Make devlink_flash_update_begin_notify and
devlink_flash_update_end_notify static, and call them in devlink.c core
code. Always send the begin_notify just before calling the driver's
flash_update routine. Always send the end_notify just after the routine
returns regardless of success or failure.
Doing this makes the status notification easier to use from the driver,
as it no longer needs to worry about catching failures and cleaning up
by calling devlink_flash_update_end_notify. It is now no longer possible
to do the wrong thing in this regard. We also save a couple of lines of
code in each driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All drivers which implement the devlink flash update support, with the
exception of netdevsim, use either request_firmware or
request_firmware_direct to locate the firmware file. Rather than having
each driver do this separately as part of its .flash_update
implementation, perform the request_firmware within net/core/devlink.c
Replace the file_name parameter in the struct devlink_flash_update_params
with a pointer to the fw object.
Use request_firmware rather than request_firmware_direct. Although most
Linux distributions today do not have the fallback mechanism
implemented, only about half the drivers used the _direct request, as
compared to the generic request_firmware. In the event that
a distribution does support the fallback mechanism, the devlink flash
update ought to be able to use it to provide the firmware contents. For
distributions which do not support the fallback userspace mechanism,
there should be essentially no difference between request_firmware and
request_firmware_direct.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 39a6f4bce6 ("b44: replace the ssb_dma API with the generic DMA API")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1605582131-36735-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VFs do not have access permissions to issue NVM_GET_DEV_INFO
firmware command.
Fixes: 4933f6753b ("bnxt_en: Add bnxt_hwrm_nvm_get_dev_info() to query NVM info.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bnxt_add_one_ctr() adds a hardware counter to a software counter and
adjusts for the hardware counter wraparound against the mask. The logic
assumes that the hardware counter is always smaller than or equal to
the mask.
This assumption is mostly correct. But in some cases if the firmware
is older and does not provide the accurate mask, the driver can use
a mask that is smaller than the actual hardware mask. This can cause
some extra carry bits to be added to the software counter, resulting in
counters that far exceed the actual value. Fix it by masking the
hardware counter with the mask passed into bnxt_add_one_ctr().
Fixes: fea6b33355 ("bnxt_en: Accumulate all counters.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Firmware is unable to retain the port counters during any kind of
fatal or non-fatal resets, so we must clear the port counters to
avoid false detection of port counter overflow.
Fixes: fea6b33355 ("bnxt_en: Accumulate all counters.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The module eeprom address range returned by bnxt_get_module_eeprom()
should be 256 bytes of A0h address space, the lower half of the A2h
address space, and page 0 for the upper half of the A2h address space.
Fix the firmware call by passing page_number 0 for the A2h slave address
space.
Fixes: 42ee18fe4c ("bnxt_en: Add Support for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPRO")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the AER or firmware reset flow, if we are in fatal error state or
if pci_channel_offline() is true, we don't send any commands to the
firmware because the commands will likely not reach the firmware and
most commands don't matter much because the firmware is likely to be
reset imminently.
However, the HWRM_FUNC_RESET command is different and we should always
attempt to send it. In the AER flow for example, the .slot_reset()
call will trigger this fw command and we need to try to send it to
effect the proper reset.
Fixes: b340dc680e ("bnxt_en: Avoid sending firmware messages when AER error is detected.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a PCIe fatal error occurs, the internal latched BAR addresses
in the chip get reset even though the BAR register values in config
space are retained.
pci_restore_state() will not rewrite the BAR addresses if the
BAR address values are valid, causing the chip's internal BAR addresses
to stay invalid. So we need to zero the BAR registers during PCIe fatal
error to force pci_restore_state() to restore the BAR addresses. These
write cycles to the BAR registers will cause the proper BAR addresses to
latch internally.
Fixes: 6316ea6db9 ("bnxt_en: Enable AER support.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As part of the commit b148bb238c
("bnxt_en: Fix possible crash in bnxt_fw_reset_task()."),
cancel_delayed_work_sync() is called only for VFs to fix a possible
crash by cancelling any pending delayed work items. It was assumed
by mistake that the flush_workqueue() call on the PF would flush
delayed work items as well.
As flush_workqueue() does not cancel the delayed workqueue, extend
the fix for PFs. This fix will avoid the system crash, if there are
any pending delayed work items in fw_reset_task() during driver's
.remove() call.
Unify the workqueue cleanup logic for both PF and VF by calling
cancel_work_sync() and cancel_delayed_work_sync() directly in
bnxt_remove_one().
Fixes: b148bb238c ("bnxt_en: Fix possible crash in bnxt_fw_reset_task().")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A recent patch has moved the workqueue cleanup logic before
calling unregister_netdev() in bnxt_remove_one(). This caused a
regression because the workqueue can be restarted if the device is
still open. Workqueue cleanup must be done after unregister_netdev().
The workqueue will not restart itself after the device is closed.
Call bnxt_cancel_sp_work() after unregister_netdev() and
call bnxt_dl_fw_reporters_destroy() after that. This fixes the
regession and the original NULL ptr dereference issue.
Fixes: b16939b59c ("bnxt_en: Fix NULL ptr dereference crash in bnxt_fw_reset_task()")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds FW versions stored in the flash to devlink info_get
callback. Return the correct fw.psid running version using the
newly added bp->nvm_cfg_ver.
v2:
Ensure stored pkg_name string is NULL terminated when copied to
devlink.
Return directly from the last call to bnxt_dl_info_put().
If the FW call to get stored version fails for any reason, return
success immediately to devlink without the stored versions.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-10-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a new function bnxt_dl_info_put() to simplify the code, as there
are more stored firmware version fields to be added in the next patch.
Also, rename fw_ver variable name to ncsi_ver for better naming while
copying to devlink info_get cb.
v2:
Ensure active_pkg_name string is NULL terminated when copied to
devlink.
Return directly from the last call to bnxt_dl_info_put().
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-9-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a new bnxt_hwrm_nvm_get_dev_info() to query firmware version
information via NVM_GET_DEV_INFO firmware command. Use it to
get the running version of the NVM configuration information.
This new function will also be used in subsequent patches to get the
stored firmware versions.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-8-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the VF virtual link is set to always enabled, the speed may be
unknown when the physical link is down. The driver currently logs
the link speed as 4294967295 Mbps which is SPEED_UNKNOWN. Modify
the link up log message as "speed unknown" which makes more sense.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-7-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
event_data1 and event_data2 are used when processing most events.
Store these in local variables at the beginning of the function to
simplify many of the case statements.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-5-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, bp->msg_enable has default value of 0. It is more useful
to have the commonly used NETIF_MSG_DRV and NETIF_MSG_HW enabled by
default.
v2: Change the fall back bnxt_reset_task() inside bnxt_rx_ring_reset()
to silent mode. With older fw, we would take the fall back path and
it would be very noisy.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-4-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Online self tests are not disruptive and can be run in NPAR mode
and in multi-host NIC as well.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-3-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If NVRAM resources are locked, NVM writes are not permitted. In such
scenarios, firmware returns HWRM_ERR_CODE_RESOURCE_LOCKED error to
firmware commands.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-2-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver will schedule RX ring reset when we get a buffer
error in the RX completion record. These RX buffer errors can be due
to normal out-of-buffer conditions or a permanent error in the RX
ring. Because the driver cannot distinguish between these 2
conditions, we assume all these buffer errors require reset.
This is very disruptive when it is just a normal out-of-buffer
condition. Newer firmware will now monitor the rings for the permanent
failure and will send a notification to the driver when it happens.
This allows the driver to reset only when such a notification is
received. In environments where we have predominently out-of-buffer
conditions, we now can avoid these unnecessary resets.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
