Add i915 parameter to I915_STATE_WARN() and use device based logging.
Done using cocci + hand edited where there was no i915 local variable
ready.
v2: avoid null deref in verify_connector_state()
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512181658.1735594-1-jani.nikula@intel.com
XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy
has a dedicated PIPE 5.2 Message bus for configuration. This message
bus is used to configure the phy internal registers.
XELPDP has C10 phys to drive output to the EDP and the native output
from the display engine. Add structures, programming hardware state
readout logic. Port clock calculations are similar to DG2. Use the DG2
formulae to calculate the port clock but use the relevant pll signals.
Note: PHY lane 0 is always used for PLL programming.
Add sequences for C10 phy enable/disable phy lane reset,
powerdown change sequence and phy lane programming.
Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636
v2: Squash patches related to C10 phy message bus and pll
programming support (Jani)
Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani)
Move macro definitions (Jani)
DP rates as separate patch (Jani)
Spin out xelpdp register definitions into a separate file (Jani)
Replace macro to select registers based on phy lane with
function calls (Jani)
Fix styling issues (Jani)
Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas)
v3: Move clear request flag into try-loop
v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani)
use __intel_de_wait_for_register() instead of __intel_wait_for_register
and uncomment intel_uncore.h (Jani)
Add DP-alt support for PHY lane programming (Khaled)
v4: Add tx and cmn on c10mpllb_state (Imre)
Add missing waits for pending transactions between two message bus
writes (Imre)
General cleanups and simplifications (Imre)
v5: Few nit cleanups from rev4 (imre)
s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK)
Rebase
v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function
Fix typo in comment for REG_FIELD_PREP8 definition(Imre)
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v4)
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
Move the display related members to the struct drm_i915_private display
sub-struct. Put them under "state", as they are related to storing
values that aren't readable from the hardware, to appease the state
checker.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230117143946.2426043-3-jani.nikula@intel.com
Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.
Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.
Also some places actually needed i915_irq.h too.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com
The TV encoder has its own special clocking strategy,
which means we can't just use intel_crtc_dotclock() to
figure out what the resulting dotclock will be given
the actual DPLL port_clock. Additionally the DPLL can't
always generate exactly the frequency we initially asked
for. This results in us computing a bogus dotclock/etc.,
and it won't match the readout which is handled by the
encoder itself properly. Naturally the state checker
becomes unhappy with the mismatch.
To do this sanely we'll need to move the DPLL computation
into encoder->compute_config() so that all the derived
state gets correctly computed based on the actual DPLL
output frequency. Start doing that just for the TV encoder
initally as intel_crtc_dotclock() should be able to handle
other encoder types well enough. Though eventually this
should be done for all encoder types rather than
doing it from intel_crtc_compute_config().
With this we actually do some of the DPLL state computation
twice, but we can skip the second actual .find_dpll() search
by flagging .clock_set=true after we've done it once. We also
still need to avoid clobbering the correct
adjusted_mode.crtc_clock set up by encoder->compute_config()
when called a second time from intel_crtc_compute_config().
Fixes: 665a7b0409 ("drm/i915: Feed the DPLL output freq back into crtc_state")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220909205932.32537-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Fill port_clock and hw.adjusted_mode.crtc_clock with the actual
frequency we're going to be getting from the hardware. This will
let us accurately compute all derived state that depends on those.
v2: Reintroduce iCLKIP WARN
v3: Try to deal with VLV/BXT DSI PLL as well
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-8-ville.syrjala@linux.intel.com
Only reassign the pipe's DPLL if it's going through a full
.compute_config() cycle. If OTOH it's just getting modeset
eg. in order to change cdclk there doesn't seem much point in
picking a new DPLL for it.
This should also prevent .get_dplls() from seeing a funky port_clock
for DP even in cases where the readout produces a non-standard
clock and we (for some reason) have decided to not fully recompute
the state to remedy the situation.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-7-ville.syrjala@linux.intel.com
Currently we calculate a lot of things (pixel rate, watermarks,
cdclk) trusting that the DPLL can generate the exact frequency
we ask it. In practice that is not true and there can be
certain amount of rounding involved.
To allow us to eventually get accurate numbers for all our
DPLL clock derived state we need to move the DPLL calculation
to hapen much earlier. To that end we hoist it up to the just
after the fastset checks. For now we just do the easy code
motion, and the actual back feeding of the final DPLL clock
into the state will come later.
A slight change here is that now .crtc_compute_clock()
can get called while the shared_dpll is still assigned.
But since .crtc_compute_clock() no longer assignes new
shared_dplls this is perfectly fine.
TODO: I'd actually like to do this before the fastset check
so that if the DPLL state should change we actually do the
modeset. Which I think is what the video aficionados want,
but it might not be what the fans of fastboot want. Not yet
sure how to reconcile those conflicting requirements...
v2: s/return/goto/ in error handling
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-6-ville.syrjala@linux.intel.com
The debugs in lower level DPLL code don't really provide any
useful extra information AFAICS. Better just streamline the
code and just put the necessary debugs (to identify at which
step the modeset failed) into the higher level code. In
addition we'll get the full state dump as well, which should
hopefully have enough information to figure out what went wrong.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220503182242.18797-4-ville.syrjala@linux.intel.com
Split the DPLL state computation into a separate function
from the current .get_dplls() which currently serves a dual duty
by also reserving the shared DPLLs.
v2: s/false/-EINVAL/ (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220503182242.18797-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Start splitting the .compute_crtc_clock() into two parts; one
part does the computation, the second part does the shared dpll
assignment. I want to move the actual computation part much earlier
into the compute_config() phase.
v2: dg2_crtc_get_shared_dpll() not needed (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220325123205.22140-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
All .crtc_compute_clock() implementations do the same memset() to
clear the dpll_hw_state (since we preserve it across
intel_crtc_prepare_cleared_state()). Move the memset() to the common
wrapper.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220325123205.22140-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Move some checks into intel_dpll_crtc_compute_clock() from the
caller. Avoids the caller from having to worry about all this
crap.
We'll also reorder the hw.enable vs. shared_dpll checks since
it makes sense to sanity check that we've cleared out the
old shared_dpll even if the pipe is getting disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220325123205.22140-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Remove the comment specifying the exact formulat for calculating
the DPLL frequency from the *_find_best_dpll() functions. Each
platform variant has its own way to calculate these and we have
the code already to do that. These comments are entirely redundant
and often even wrong so just get rid of them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220307233940.4161-3-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Unify vlv/chv with earlier platforms so that the sturct dpll::dot
represents the /5 clock frequency (ie. DP symbol rate or HDMI
TMDS rate) rather than the *5 fast clock (/2 of the bitrate).
Makes life a little less confusing to get the same number back
in .dot which we fed into the DPLL algorithm.
v2: Actually just include the 5x in the final P divider
Do the same change to the hand rolled gvt code
v3: Missed a few *5 in *_find_best_dpll()
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220309214301.22899-1-ville.syrjala@linux.intel.com
Remove the local onoff() implementation and adopt the
str_on_off() from linux/string_helpers.h.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220225234631.3725943-4-lucas.demarchi@intel.com
The VLV/CHV sideband code is pretty distinct from the rest of the
sideband code. Split it out to new vlv_sideband.[ch].
Pure code movement with relevant #include changes, and a tiny checkpatch
fix on top.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/755ebbbaf01fc6d306b763b6ef60f45e671ba290.1634119597.git.jani.nikula@intel.com
Move assert_panel_unlocked() to intel_pps.c and rename
assert_pps_unlocked(). Keep the functionality and the assert code
together.
There's still a bit of a split between the eDP PPS usage in intel_pps.c
and all the other PPS usage, and assert_pps_unlocked() is arguably more
related to the latter. However, intel_pps.c is the best fit for anything
touching the PPS registers.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a9b77692a145891789eefb0447e082cfc22aaa85.1632992608.git.jani.nikula@intel.com
PIPECONF becamse TRANSCONF when HSW introduced the EDP transcoder.
Bigjoiner is making life even more confusing by introducing
a N:1 relationship between pipes and transcoders. In that case
we only enable/configure the transcoder corresponding to the
master pipe. Let's do some renames to make it clear we're dealing
with the transcoder rather than pipe when it comes to
PIPECONF/TRANSCONF.
I decided to leave the _cpu_ part out from the function/macro
names since the PCH transcoder related stuff already has a
_pch_ in their name. So shouldn't be possible to confuse them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
On g4x and pch the DPLL has two P1 dividers (for refresh rate
switching). Program the FPx1 P1 divider consistently to the reduced
clock P1 divider if available, otherwise just program it to the
same value as the FPx0 P1 divider.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
When we enable the DPLL for the PPS kick, let's tell the DPLL code
we're dealing with an eDP output. This shouldn't really matter, but
it's more consistent with the way the DPLL is configured when we're
actually enabling the eDP port for real.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
DG2's SNPS PHYs incorporate a dedicated port PLL called MPLLB which
takes the place of the shared DPLLs we've used on past platforms. Let's
add the MPLLB programming sequences; they'll be plugged into the rest of
the code in future patches.
Bspec: 54032
Bspec: 53881
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Nidhi Gupta <nidhi1.gupta@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-24-matthew.d.roper@intel.com
Hoist the intel_de.h include from intel_display_types.h one
level up. I need this in order to untangle the include order
so that I can add tracepoints into intel_de.h.
This little cocci script did most of the work for me:
@find@
@@
(
intel_de_read(...)
|
intel_de_read_fw(...)
|
intel_de_write(...)
|
intel_de_write_fw(...)
)
@has_include@
@@
(
#include "intel_de.h"
|
#include "display/intel_de.h"
)
@depends on find && !has_include@
@@
+ #include "intel_de.h"
#include "intel_display_types.h"
@depends on find && !has_include@
@@
+ #include "display/intel_de.h"
#include "display/intel_display_types.h"
Cc: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-1-ville.syrjala@linux.intel.com
While converting the rest of the driver to use GRAPHICS_VER() and
MEDIA_VER(), following what was done for display, some discussions went
back on what we did for display:
1) Why is the == comparison special that deserves a separate
macro instead of just getting the version and comparing directly
like is done for >, >=, <=?
2) IS_DISPLAY_RANGE() is weird in that it omits the "_VER" for
brevity. If we remove the current users of IS_DISPLAY_VER(), we
could actually repurpose it for a range check
With (1) there could be an advantage if we used gen_mask since multiple
conditionals be combined by the compiler in a single and instruction and
check the result. However a) INTEL_GEN() doesn't use the mask since it
would make the code bigger everywhere else and b) in the cases it made
sense, it also made sense to convert to the _RANGE() variant.
So here we repurpose IS_DISPLAY_VER() to work with a [ from, to ] range
like was the IS_DISPLAY_RANGE() and convert the current IS_DISPLAY_VER()
users to use == and != operators. Aside from the definition changes,
this was done by the following semantic patch:
@@ expression dev_priv, E1; @@
- !IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) != E1
@@ expression dev_priv, E1; @@
- IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) == E1
@@ expression dev_priv, from, until; @@
- IS_DISPLAY_RANGE(dev_priv, from, until)
+ IS_DISPLAY_VER(dev_priv, from, until)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
[Jani: Minor conflict resolve while applying.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210413051002.92589-4-lucas.demarchi@intel.com
Now that we've eliminated INTEL_GEN(), IS_GEN_RANGE(), etc. from the
display code, we should also kill off our use of the IS_GEN9_* macros
too. We'll do the conversion manually this time instead of using
Coccinelle since the most logical substitution can depend heavily on the
code context, and sometimes we can keep the code simpler if we make
additional adjustments such as swapping the order of if/else arms.
v2:
- Restore a lost negation in intel_pll_is_valid().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210407203945.1432531-1-matthew.d.roper@intel.com
(cherry picked from commit 70bfb30743)
[Jani: cherry picked to topic branch to reduce conflicts]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
