The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert the mediatek drm drivers from always returning zero in
the remove callback to the void returning variant.
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230801110239.831099-8-u.kleine-koenig@pengutronix.de/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The interrupt handler for HPD is useful only if a display is actually
supposed to be hotpluggable, as that manages the machinery to perform
cable (un)plug detection, debouncing and setup for re-training.
Since eDP panels are not supposed to be hotpluggable we can avoid
using the HPD interrupts altogether and rely on HPD polling only
for the suspend/resume case, saving us some spinlocking action and
the overhead of interrupts firing at every suspend/resume cycle,
achieving a faster (even if just slightly) display resume.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-12-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In order to support usecases in which the panel regulator can be
switched on and off to save power, and usecases in which the panel
regulator is off at boot, add a .wait_hpd_asserted() callback for
the AUX bus: this will make sure to wait until the panel is fully
ready after power-on before trying to communicate with it.
Also, parse the eDP display capabilities in that callback, so that
we can also avoid using the .get_edid() callback from this bridge.
Since at this point the hpd machinery is performed in the new hpd
callback and the detection and edid reading are done outside of
this driver, assign the DRM_BRIDGE_OP_{DETECT, EDID, HPD} ops and
register the bridge unconditionally at probe time only if we are
probing full DisplayPort and not eDP while, for the latter, we
register the bridge in the .done_probing() callback and only if
the panel was found and triggered HPD.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-11-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
For the eDP case we can support using aux-bus on MediaTek DP: this
gives us the possibility to declare our panel as generic "panel-edp"
which will automatically configure the timings and available modes
via the EDID that we read from it.
To do this, move the panel parsing at the end of the probe function
so that the hardware is initialized beforehand and also initialize
the DPTX AUX block and power both on as, when we populate the
aux-bus, the panel driver will trigger an EDID read to perform
panel detection.
Last but not least, since now the AUX transfers can happen in the
separated aux-bus, it was necessary to add an exclusion for the
cable_plugged_in check in `mtk_dp_aux_transfer()` and the easiest
way to do this is to simply ignore checking that when the bridge
type is eDP.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-10-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In preparation for adding support for eDP, move the PHY registration
code to a new mtk_dp_register_phy() function for better readability.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-9-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
If a controller (usually, eDP!) does not support audio, or audio is not
enabled because the endpoint has no audio support, it's useless to lock
a mutex only to unlock it right after because there's no .plugged_cb().
Check if the audio is supported and enabled before locking the mutex in
mtk_dp_update_plugged_status(): if not, we simply return immediately.
While at it, since the update_plugged_status_lock mutex would not be
used if the controller doesn't support audio at all, initialize it
only if `audio_supported` is true.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-8-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
It is useless and error-prone to enable the DisplayPort event interrupt
before finishing to probe and install the driver, as the DP training
cannot happen before the entire pipeline is correctly set up, as the
interrupt handler also requires the full hardware to be initialized by
mtk_dp_bridge_attach().
Anyway, depending in which state the controller is left from the
bootloader, this may cause an interrupt storm and consequently hang
the kernel during boot, so, avoid enabling the interrupt until we
reach a clean state by adding the IRQ_NOAUTOEN flag before requesting
it at probe time and manage the enablement of the ISR in the .attach()
and .detach() handlers for the DP bridge.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-7-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Move the register write to MTK_DP_AUX_P0_3690 to set the AUX reply mode
to function mtk_dp_initialize_aux_settings(), as this is effectively
part of the DPTX AUX setup sequence.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-6-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In preparation for adding support for aux-bus, which will add a code
path that may fail after the drm_bridge_add() call, change that to
devm_drm_bridge_add() to simplify failure paths later.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-5-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Change logging from drm_{err,info}() to dev_{err,info}() in functions
mtk_dp_aux_transfer() and mtk_dp_aux_do_transfer(): this will be
essential to avoid getting NULL pointer kernel panics if any kind
of error happens during AUX transfers happening before the bridge
is attached.
This may potentially start happening in a later commit implementing
aux-bus support, as AUX transfers will be triggered from the panel
driver (for EDID) before the mtk-dp bridge gets attached, and it's
done in preparation for the same.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-4-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Everytime we run bridge detection and/or EDID read we run a poweron
and poweroff sequence for both the AUX and the panel; moreover, this
is also done when enabling the bridge in the .atomic_enable() callback.
Move this power on/off sequence to a new mtk_dp_aux_panel_poweron()
function as to commonize it.
Note that, before this commit, in mtk_dp_bridge_atomic_enable() only
the AUX was getting powered on but the panel was left powered off if
the DP cable wasn't plugged in while now we unconditionally send a D0
request and this is done for two reasons:
- First, whether this request fails or not, it takes the same time
and anyway the DP hardware won't produce any error (or, if it
does, it's ignorable because it won't block further commands)
- Second, training the link between a sleeping/standby/unpowered
display makes little sense.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-3-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
If reading the RX capabilities fails the training pattern will be set
wrongly: add error checking for drm_dp_read_dpcd_caps() and return if
anything went wrong with it.
While at it, also add a less critical error check when writing to
clear the ESI0 IRQ vector.
Fixes: f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-2-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
DP 1.4a Section 2.8.7.1.5.6.1:
A DP Source device shall retry at least seven times upon receiving
AUX_DEFER before giving up the AUX transaction.
The drm_dp_i2c_do_msg() function in the drm_dp_helper.c file will
judge the status of the msg->reply parameter passed to aux_transfer
for different processing.
Fixes: f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1680072203-10394-1-git-send-email-xinlei.lee@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The MediaTek DisplayPort interface bridge driver starts its interrupts
as soon as its probed. However when the interrupts trigger the bridge
might not have been attached to a DRM device. As drm_helper_hpd_irq_event()
does not check whether the passed in drm_device is valid or not, a NULL
pointer passed in results in a kernel NULL pointer dereference in it.
Check whether the bridge is attached and only trigger an HPD event if
it is.
Fixes: f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Guillaume Ranquet <granquet@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230202045734.2773503-1-wenst@chromium.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
1. Reduce the time of dsi from LP11 to sending cmd
2. Remove dependency on GEM DMA helper
3. Drop unbalanced obj unref
4. Fix the fallback for mediatek,mt8186-disp-ccorr
5. Fixup for error path.
-----BEGIN PGP SIGNATURE-----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=ZhnI
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 6.3
1. Reduce the time of dsi from LP11 to sending cmd
2. Remove dependency on GEM DMA helper
3. Drop unbalanced obj unref
4. Fix the fallback for mediatek,mt8186-disp-ccorr
5. Fixup for error path.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130125811.2567-1-chunkuang.hu@kernel.org
Commit f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort
driver") added usage of the drm_bridge_chain_ functions which are
to be deprecated.
Replace with the drm_atomic_bridge_chain_ variants using the
current state.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221205173328.1395350-3-dave.stevenson@raspberrypi.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
mtk_dp_driver is only used in mtk_dp.c now, change it
to static.
Fixes: f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220913134929.1970187-1-yangyingliang@huawei.com
In order to improve human readability, reduce the indentation by
returning early if the dp/edp cable is not plugged in.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916133821.27980-2-rex-bc.chen@mediatek.com
This patch adds audio support to the DP driver for MT8195 with up to 8
channels.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-11-rex-bc.chen@mediatek.com
From the DP spec 1.4a chapter 3.3, upstream devices should implement
HPD signal de-bouncing on an external connection.
A period of 100ms should be used to detect an HPD connect event.
To cover these cases, HPD de-bounce should be implemented only after
HPD low has been detected for at least 100ms.
Therefore,
1. If HPD is low (which means plugging out) for longer than 100ms:
we need to do de-bouncing (which means we need to wait for 100ms).
2. If HPD low is for less than 100ms:
we don't need to care about the de-bouncing.
In this patch, we start a 100ms timer and use a need_debounce boolean
to implement the feature.
Two cases when HPD is high:
1. If the timer is expired (>100ms):
- need_debounce is true.
- When HPD high (plugging event comes), need_debounce will be true
and then we need to do de-bouncing (wait for 100ms).
2. If the timer is not expired (<100ms):
- need_debounce is false.
- When HPD high (plugging event comes), need_debounce will be false
and no need to do de-bouncing.
HPD_______ __________________
| |<- 100ms ->
|____________|
<- 100ms ->
Without HPD de-bouncing, USB-C to HDMI Adapaters will not be detected.
The change has been successfully tested with the following devices:
- Dell Adapter - USB-C to HDMI
- Acer 1in1 HDMI dongle
- Ugreen 1in1 HDMI dongle
- innowatt HDMI + USB3 hub
- Acer 2in1 HDMI dongle
- Apple 3in1 HDMI dongle (A2119)
- J5Create 3in1 HDMI dongle (JAC379)
Tested-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-10-rex-bc.chen@mediatek.com
Add External DisplayPort support to the MT8195 eDP driver.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-9-rex-bc.chen@mediatek.com
It's not necessary to have a next_bridge for DP device, so we add this
patch to judge this.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-8-rex-bc.chen@mediatek.com
The calibration data formats of eDP and DP are different. We add
"const struct mtk_dp_efuse_fmt *efuse_fmt" to the device data to
define them.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-7-rex-bc.chen@mediatek.com
The smc commands of eDP and DP are different. We add smc_cmd to the
device data to define them.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-6-rex-bc.chen@mediatek.com
The bridge types of eDP and DP are different. We add device data to
this driver and add bridge_type to the device data to define them.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-5-rex-bc.chen@mediatek.com
This patch adds a embedded displayport driver for the MediaTek mt8195 SoC.
It supports the MT8195, the embedded DisplayPort units. It offers
DisplayPort 1.4 with up to 4 lanes.
The driver creates a child device for the phy. The child device will
never exist without the parent being active. As they are sharing a
register range, the parent passes a regmap pointer to the child so that
both can work with the same register range. The phy driver sets device
data that is read by the parent to get the phy device that can be used
to control the phy properties.
This driver is based on an initial version by
Jitao shi <jitao.shi@mediatek.com>
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-4-rex-bc.chen@mediatek.com
