The existing code does not allow the MTU to be set to the maximum even
after an XDP program supporting multiple buffers is attached. Fix it
to set the netdev->max_mtu to the maximum value if the attached XDP
program supports mutiple buffers, regardless of the current MTU value.
Also use a local variable dev instead of repeatedly using bp->dev.
Fixes: 1dc4c557bf ("bnxt: adding bnxt_xdp_build_skb to build skb from multibuffer xdp_buff")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230731142043.58855-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RXBD length field on all bnxt chips is 16-bit and so we cannot
support a full page when the native page size is 64K or greater.
The non-XDP (non page pool) code path has logic to handle this but
the XDP page pool code path does not handle this. Add the missing
logic to use page_pool_dev_alloc_frag() to allocate 32K chunks if
the page size is 64K or greater.
Fixes: 9f4b28301c ("bnxt: XDP multibuffer enablement")
Link: https://lore.kernel.org/netdev/20230728231829.235716-2-michael.chan@broadcom.com/
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230731142043.58855-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similarly to other recently fixed drivers make sure we don't
try to access XDP or page pool APIs when NAPI budget is 0.
NAPI budget of 0 may mean that we are in netpoll.
This may result in running software IRQs in hard IRQ context,
leading to deadlocks or crashes.
To make sure bnapi->tx_pkts don't get wiped without handling
the events, move clearing the field into the handler itself.
Remember to clear tx_pkts after reset (bnxt_enable_napi())
as it's technically possible that netpoll will accumulate
some tx_pkts and then a reset will happen, leaving tx_pkts
out of sync with reality.
Fixes: 322b87ca55 ("bnxt_en: add page_pool support")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230728205020.2784844-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link VF representors to parent PCI device to benefit from
systemd defined naming scheme.
Without this change the representor is visible as ethN.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230620144855.288443-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
Conflicts:
net/sched/sch_taprio.c
d636fc5dd6 ("net: sched: add rcu annotations around qdisc->qdisc_sleeping")
dced11ef84 ("net/sched: taprio: don't overwrite "sch" variable in taprio_dump_class_stats()")
net/ipv4/sysctl_net_ipv4.c
e209fee411 ("net/ipv4: ping_group_range: allow GID from 2147483648 to 4294967294")
ccce324dab ("tcp: make the first N SYN RTO backoffs linear")
https://lore.kernel.org/all/20230605100816.08d41a7b@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As per the new udp tunnel framework, drivers which need to know the
details of a port entry (i.e. port type) when it gets deleted should
use the .set_port / .unset_port callbacks.
Implementing the current .udp_tunnel_sync callback would mean that the
deleted tunnel port entry would be all zeros. This used to work on
older firmware because it would not check the input when deleting a
tunnel port. With newer firmware, the delete will now fail and
subsequent tunnel port allocation will fail as a result.
Fixes: 442a35a5a7 ("bnxt: convert to new udp_tunnel_nic infra")
Reviewed-by: Kalesh Anakkur Purayil <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The firmware can send PHC_RTC_UPDATE async event on a PF that may not
have PTP registered. In such a case, there will be a null pointer
deference for bp->ptp_cfg when we try to handle the event.
Fix it by not registering for this event with the firmware if !bp->ptp_cfg.
Also, check that bp->ptp_cfg is valid before proceeding when we receive
the event.
Fixes: 8bcf6f04d4 ("bnxt_en: Handle async event when the PHC is updated in RTC mode")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Driver starts firmware fatal error recovery by detecting
heartbeat failure or fw reset count register changing. But
these checks are not reliable if the device is not accessible.
This can happen while DPC (Downstream Port containment) is in
progress. Skip firmware fatal recovery if pci_device_is_present()
returns false.
Fixes: acfb50e4e7 ("bnxt_en: Add FW fatal devlink_health_reporter.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We need to call bnxt_hwrm_func_qcfg() on a VF to query the default
VLAN that may be setup by the PF. If a default VLAN is enabled,
the VF cannot support VLAN acceleration on the receive side and
the VNIC must be setup to strip out the default VLAN tag. If a
default VLAN is not enabled, the VF can support VLAN acceleration
on the receive side. The VNIC should be set up to strip or not
strip the VLAN based on the RX VLAN acceleration setting.
Without this call to determine the default VLAN before calling
bnxt_setup_vnic(), the VNIC may not be set up correctly. For
example, bnxt_setup_vnic() may set up to strip the VLAN tag based
on stale default VLAN information. If RX VLAN acceleration is
not enabled, the VLAN tag will be incorrectly stripped and the
RX data path will not work correctly.
Fixes: cf6645f8eb ("bnxt_en: Add function for VF driver to query default VLAN.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Only older NIC controller's firmware uses the PROC AP reset type.
Firmware on 5731X/5741X and newer chips does not support this reset
type. When bnxt_reset() issues a series of resets, this PROC AP
reset may actually fail on these newer chips because the firmware
is not ready to accept this unsupported command yet. Avoid this
unnecessary error by skipping this reset type on chips that don't
support it.
Fixes: 7a13240e37 ("bnxt_en: fix ethtool_reset_flags ABI violations")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We must specify the vnic id of the vnic in the input structure of this
firmware message. Otherwise we will get an error from the firmware.
Fixes: 98a4322b70 ("bnxt_en: update RSS config using difference algorithm")
Reviewed-by: Kalesh Anakkur Purayil <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The down condition should be the negation of the wake condition,
IOW when I moved it from:
if (cond && wake())
to
if (__netif_txq_completed_wake(cond))
Cond should have been negated. Flip it now.
This bug leads to occasional crashes with netconsole.
It may also lead to queue never waking up in case BQL is not enabled.
Reported-by: David Wei <davidhwei@meta.com>
Fixes: 08a096780d ("bnxt: use new queue try_stop/try_wake macros")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230607010826.960226-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The remaining users calling __skb_frag_set_page() with
page being NULL seems to be doing defensive programming,
as shinfo->nr_frags is already decremented, so remove
them.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users use __skb_frag_set_page()/skb_frag_off_set()/
skb_frag_size_set() to fill the page desc for a skb frag.
Introduce skb_frag_fill_page_desc() to do that.
net/bpf/test_run.c does not call skb_frag_off_set() to
set the offset, "copy_from_user(page_address(page), ...)"
and 'shinfo' being part of the 'data' kzalloced in
bpf_test_init() suggest that it is assuming offset to be
initialized as zero, so call skb_frag_fill_page_desc()
with offset being zero for this case.
Also, skb_frag_set_page() is not used anymore, so remove
it.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usual wide collection of unrelated items in drivers:
- Driver bug fixes and treewide cleanups in hfi1, siw, qib, mlx5, rxe,
usnic, usnic, bnxt_re, ocrdma, iser
* Unnecessary NULL checks
* kmap obsolescence
* pci_enable_pcie_error_reporting() obsolescence
* Unused variables and macros
* trace event related warnings
* casting warnings
- Code cleanups for irdm and erdma
- EFA reporting of 128 byte PCIe TLP support
- mlx5 more agressively uses the out of order HW feature
- Big rework of how state machines and tasks work in rxe
- Fix a syzkaller found crash netdev refcount leak in siw
- bnxt_re revises their HW description header
- Congestion control for bnxt_re
- Use mmu_notifiers more safely in hfi1
- mlx5 gets better support for PCIe relaxed ordering inside VMs
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRRRCHOFoQz/8F5bUaFwuHvBreFYQUCZEva5wAKCRCFwuHvBreF
YZFmAQC9T3b/XQ3bRknYciuzbatC98o9xB0FTqmEFYGj+Y2lVAD9EEVe3HKfHfi3
t/GxXYB5r22oxg5bgsblZfEdEdTVCg8=
=akMm
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"Usual wide collection of unrelated items in drivers:
- Driver bug fixes and treewide cleanups in hfi1, siw, qib, mlx5,
rxe, usnic, usnic, bnxt_re, ocrdma, iser:
- remove unnecessary NULL checks
- kmap obsolescence
- pci_enable_pcie_error_reporting() obsolescence
- unused variables and macros
- trace event related warnings
- casting warnings
- Code cleanups for irdm and erdma
- EFA reporting of 128 byte PCIe TLP support
- mlx5 more agressively uses the out of order HW feature
- Big rework of how state machines and tasks work in rxe
- Fix a syzkaller found crash netdev refcount leak in siw
- bnxt_re revises their HW description header
- Congestion control for bnxt_re
- Use mmu_notifiers more safely in hfi1
- mlx5 gets better support for PCIe relaxed ordering inside VMs"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (81 commits)
RDMA/efa: Add rdma write capability to device caps
RDMA/mlx5: Use correct device num_ports when modify DC
RDMA/irdma: Drop spurious WQ_UNBOUND from alloc_ordered_workqueue() call
RDMA/rxe: Fix spinlock recursion deadlock on requester
RDMA/mlx5: Fix flow counter query via DEVX
RDMA/rxe: Protect QP state with qp->state_lock
RDMA/rxe: Move code to check if drained to subroutine
RDMA/rxe: Remove qp->req.state
RDMA/rxe: Remove qp->comp.state
RDMA/rxe: Remove qp->resp.state
RDMA/mlx5: Allow relaxed ordering read in VFs and VMs
net/mlx5: Update relaxed ordering read HCA capabilities
RDMA/mlx5: Check pcie_relaxed_ordering_enabled() in UMR
RDMA/mlx5: Remove pcie_relaxed_ordering_enabled() check for RO write
RDMA: Add ib_virt_dma_to_page()
RDMA/rxe: Fix the error "trying to register non-static key in rxe_cleanup_task"
RDMA/irdma: Slightly optimize irdma_form_ah_cm_frame()
RDMA/rxe: Fix incorrect TASKLET_STATE_SCHED check in rxe_task.c
IB/hfi1: Place struct mmu_rb_handler on cache line start
IB/hfi1: Fix bugs with non-PAGE_SIZE-end multi-iovec user SDMA requests
...
The patch in fixes changed the way real-time mode is chosen for PHC on
the NIC. Apparently there is one more use case of the check outside of
ptp part of the driver which was not converted to the new macro and is
making a lot of noise in free-running mode.
Fixes: 131db49916 ("bnxt_en: reset PHC frequency in free-running mode")
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230418202511.1544735-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the driver unload path, the driver currently checks the valid
BNXT_FLAG_ROCE_CAP flag in bnxt_rdma_aux_device_uninit() before
proceeding. This is flawed because the flag may not be set initially
during driver load. It may be set later after the NVRAM setting is
changed followed by a firmware reset. Relying on the
BNXT_FLAG_ROCE_CAP flag may crash in bnxt_rdma_aux_device_uninit() if
the aux device was never initialized:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
PGD 8ae6aa067 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 39 PID: 42558 Comm: rmmod Kdump: loaded Tainted: G OE --------- - - 4.18.0-348.el8.x86_64 #1
Hardware name: Dell Inc. PowerEdge R750/0WT8Y6, BIOS 1.5.4 12/17/2021
RIP: 0010:device_del+0x1b/0x410
Code: 89 a5 50 03 00 00 4c 89 a5 58 03 00 00 eb 89 0f 1f 44 00 00 41 56 41 55 41 54 4c 8d a7 80 00 00 00 55 53 48 89 fb 48 83 ec 18 <48> 8b 2f 4c 89 e7 65 48 8b 04 25 28 00 00 00 48 89 44 24 10 31 c0
RSP: 0018:ff7f82bf469a7dc8 EFLAGS: 00010292
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000206 RDI: 0000000000000000
RBP: ff31b7cd114b0ac0 R08: 0000000000000000 R09: ffffffff935c3400
R10: ff31b7cd45bc3440 R11: 0000000000000001 R12: 0000000000000080
R13: ffffffffc1069f40 R14: 0000000000000000 R15: 0000000000000000
FS: 00007fc9903ce740(0000) GS:ff31b7d4ffac0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000992fee004 CR4: 0000000000773ee0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
bnxt_rdma_aux_device_uninit+0x1f/0x30 [bnxt_en]
bnxt_remove_one+0x2f/0x1f0 [bnxt_en]
pci_device_remove+0x3b/0xc0
device_release_driver_internal+0x103/0x1f0
driver_detach+0x54/0x88
bus_remove_driver+0x77/0xc9
pci_unregister_driver+0x2d/0xb0
bnxt_exit+0x16/0x2c [bnxt_en]
__x64_sys_delete_module+0x139/0x280
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
RIP: 0033:0x7fc98f3af71b
Fix this by modifying the check inside bnxt_rdma_aux_device_uninit()
to check for bp->aux_priv instead. We also need to make some changes
in bnxt_rdma_aux_device_init() to make sure that bp->aux_priv is set
only when the aux device is fully initialized.
Fixes: d80d88b0df ("bnxt_en: Add auxiliary driver support")
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver does not support PTP on these older chips and it is assuming
that firmware on these older chips will not return the
PORT_MAC_PTP_QCFG_RESP_FLAGS_HWRM_ACCESS flag in __bnxt_hwrm_ptp_qcfg(),
causing the function to abort quietly.
But newer firmware now sets this flag and so __bnxt_hwrm_ptp_qcfg()
will proceed further. Eventually it will fail in bnxt_ptp_init() ->
bnxt_map_ptp_regs() because there is no code to support the older chips.
The driver will then complain:
"PTP initialization failed.\n"
Fix it so that we abort quietly earlier without going through the
unnecessary steps and alarming the user with the warning log.
Fixes: ae5c42f0b9 ("bnxt_en: Get PTP hardware capability from firmware")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
bnxt has 1:1 mapping of page pools and NAPIs, so it's safe
to hoook them up together.
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Tested-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric points out that we should make sure that ring index updates
are wrapped in the appropriate READ_ONCE/WRITE_ONCE macros.
Suggested-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Remove an inability of bnxt_en driver to set eswitch to switchdev
mode without existing VFs by:
1. Allow to set switchdev mode in bnxt_dl_eswitch_mode_set() so
representors are created only when num_vfs > 0 otherwise just
set bp->eswitch_mode
2. Do not automatically change bp->eswitch_mode during
bnxt_vf_reps_create() and bnxt_vf_reps_destroy() calls so
the eswitch mode is managed only by an user by devlink.
Just set temporarily bp->eswitch_mode to legacy to avoid
re-opening of representors during destroy.
3. Create representors in bnxt_sriov_enable() if current eswitch
mode is switchdev one
Tested by this sequence:
1. Set PF interface up
2. Set PF's eswitch mode to switchdev
3. Created N VFs
4. Checked that N representors were created
5. Set eswitch mode to legacy
6. Checked that representors were deleted
7. Set eswitch mode back to switchdev
8. Checked that representors exist again for VFs
9. Deleted all VFs
10. Checked that all representors were deleted as well
11. Checked that current eswitch mode is still switchdev
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Link: https://lore.kernel.org/r/20230411120443.126055-1-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Drivers call netdev_tx_completed_queue() right before
netif_txq_maybe_wake(). If BQL is enabled netdev_tx_completed_queue()
should issue a memory barrier, so we can depend on that separating
the stop check from the consumer index update, instead of adding
another barrier in netif_txq_maybe_wake().
This matters more than the barriers on the xmit path, because
the wake condition is almost always true. So we issue the
consumer side barrier often.
Wrap netdev_tx_completed_queue() in a local helper to issue
the barrier even if BQL is disabled. Keep the same semantics
as netdev_tx_completed_queue() (barrier only if bytes != 0)
to make it clear that the barrier is conditional.
Plus since macro gets pkt/byte counts as arguments now -
we can skip waking if there were no packets completed.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert bnxt to use new macros rather than open code the logic.
Two differences:
(1) bnxt_tx_int() will now only issue a memory barrier if it sees
enough space on the ring to wake the queue. This should be fine,
the mb() is between the writes to the ring pointers and checking
queue state.
(2) we'll start the queue instead of waking on race, this should
be safe inside the xmit handler.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Updating the HW structures to the latest version.
This is copied from the code maintained internally. No functionality
changes in this patch. Code is re-organized to match the file maintained
in the internal tree. Also, New HW interface structures are added, which
will be used by the drivers in future.
CC: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://lore.kernel.org/r/1680169540-10029-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bnxt_fw_to_ethtool_speed() is missing the case statement for 200G
link speed reported by firmware. As a result, ethtool will report
unknown speed when the firmware reports 200G link speed.
Fixes: 532262ba3b ("bnxt_en: ethtool: support PAM4 link speeds up to 200G")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix 57502 and 57508 NPAR description string entries. The typos
caused these devices to not match up with lspci output.
Fixes: 49c98421e6 ("bnxt_en: Add PCI IDs for 57500 series NPAR devices.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the selftest command fails, driver is not reporting the failure
by updating the "test->flags" when bnxt_close_nic() fails.
Fixes: eb51365846 ("bnxt_en: Add basic ethtool -t selftest support.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently driver performs software based frequency adjustments
when RTC capability is not discovered or when in shared PHC mode.
But there may be some old firmware versions that still support
hardware freq adjustments without RTC capability being exposed.
In this situation driver will use non-realtime mode even on single
host NICs.
Hence enforce software frequency adjustments only when running in
shared PHC mode. Make suitable changes for cyclecounter for the
same.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Driver uses the flag BNXT_FLAG_MULTI_HOST to determine whether
to use non-realtime mode PHC when running on a multi host NIC.
However when ptp initializes on a NIC with shared PHC, we still
don't have this flag set yet because HWRM_FUNC_QCFG is issued
much later.
Move the ptp initialization code after we have issued func_qcfg.
The next patch will use the BNXT_FLAG_MULTI_HOST flag during PTP
initialization.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current fw_cap field (u32) has run out of bits to save any
new capability.
Change the field to u64.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The value of an arithmetic expression is subject
of possible overflow due to a failure to cast operands to a larger data
type before performing arithmetic. Used macro for multiplication instead
operator for avoiding overflow.
Found by Security Code and Linux Verification
Center (linuxtesting.org) with SVACE.
Signed-off-by: Maxim Korotkov <korotkov.maxim.s@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230309174347.3515-1-korotkov.maxim.s@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When using a PHC in shared between multiple hosts, the previous
frequency value may not be reset and could lead to host being unable to
compensate the offset with timecounter adjustments. To avoid such state
reset the hardware frequency of PHC to zero on init. Some refactoring is
needed to make code readable.
Fixes: 85036aee19 ("bnxt_en: Add a non-real time mode to access NIC clock")
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230310151356.678059-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver needs to keep track of all the possible concurrent TPA (GRO/LRO)
completions on the aggregation ring. On P5 chips, the maximum number
of concurrent TPA is 256 and the amount of memory we allocate is order-5
on systems using 4K pages. Memory allocation failure has been reported:
NetworkManager: page allocation failure: order:5, mode:0x40dc0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO), nodemask=(null),cpuset=/,mems_allowed=0-1
CPU: 15 PID: 2995 Comm: NetworkManager Kdump: loaded Not tainted 5.10.156 #1
Hardware name: Dell Inc. PowerEdge R660/0M1CC5, BIOS 0.2.25 08/12/2022
Call Trace:
dump_stack+0x57/0x6e
warn_alloc.cold.120+0x7b/0xdd
? _cond_resched+0x15/0x30
? __alloc_pages_direct_compact+0x15f/0x170
__alloc_pages_slowpath.constprop.108+0xc58/0xc70
__alloc_pages_nodemask+0x2d0/0x300
kmalloc_order+0x24/0xe0
kmalloc_order_trace+0x19/0x80
bnxt_alloc_mem+0x1150/0x15c0 [bnxt_en]
? bnxt_get_func_stat_ctxs+0x13/0x60 [bnxt_en]
__bnxt_open_nic+0x12e/0x780 [bnxt_en]
bnxt_open+0x10b/0x240 [bnxt_en]
__dev_open+0xe9/0x180
__dev_change_flags+0x1af/0x220
dev_change_flags+0x21/0x60
do_setlink+0x35c/0x1100
Instead of allocating this big chunk of memory and dividing it up for the
concurrent TPA instances, allocate each small chunk separately for each
TPA instance. This will reduce it to order-0 allocations.
Fixes: 79632e9ba3 ("bnxt_en: Expand bnxt_tpa_info struct to support 57500 chips.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_reserve_rings(), there is logic to check that the number of TX
rings reserved is enough to cover all the mqprio TCs, but it fails to
account for the TX XDP rings. So the check will always fail if there
are mqprio TCs and TX XDP rings. As a result, the driver always fails
to initialize after the XDP program is attached and the device will be
brought down. A subsequent ifconfig up will also fail because the
number of TX rings is set to an inconsistent number. Fix the check to
properly account for TX XDP rings. If the check fails, set the number
of TX rings back to a consistent number after calling netdev_reset_tc().
Fixes: 674f50a5b0 ("bnxt_en: Implement new method to reserve rings.")
Reviewed-by: Hongguang Gao <hongguang.gao@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCY+bZrwAKCRDbK58LschI
gzi4AP4+TYo0jnSwwkrOoN9l4f5VO9X8osmj3CXfHBv7BGWVxAD/WnvA3TDZyaUd
agIZTkRs6BHF9He8oROypARZxTeMLwM=
=nO1C
-----END PGP SIGNATURE-----
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-02-11
We've added 96 non-merge commits during the last 14 day(s) which contain
a total of 152 files changed, 4884 insertions(+), 962 deletions(-).
There is a minor conflict in drivers/net/ethernet/intel/ice/ice_main.c
between commit 5b246e533d ("ice: split probe into smaller functions")
from the net-next tree and commit 66c0e13ad2 ("drivers: net: turn on
XDP features") from the bpf-next tree. Remove the hunk given ice_cfg_netdev()
is otherwise there a 2nd time, and add XDP features to the existing
ice_cfg_netdev() one:
[...]
ice_set_netdev_features(netdev);
netdev->xdp_features = NETDEV_XDP_ACT_BASIC | NETDEV_XDP_ACT_REDIRECT |
NETDEV_XDP_ACT_XSK_ZEROCOPY;
ice_set_ops(netdev);
[...]
Stephen's merge conflict mail:
https://lore.kernel.org/bpf/20230207101951.21a114fa@canb.auug.org.au/
The main changes are:
1) Add support for BPF trampoline on s390x which finally allows to remove many
test cases from the BPF CI's DENYLIST.s390x, from Ilya Leoshkevich.
2) Add multi-buffer XDP support to ice driver, from Maciej Fijalkowski.
3) Add capability to export the XDP features supported by the NIC.
Along with that, add a XDP compliance test tool,
from Lorenzo Bianconi & Marek Majtyka.
4) Add __bpf_kfunc tag for marking kernel functions as kfuncs,
from David Vernet.
5) Add a deep dive documentation about the verifier's register
liveness tracking algorithm, from Eduard Zingerman.
6) Fix and follow-up cleanups for resolve_btfids to be compiled
as a host program to avoid cross compile issues,
from Jiri Olsa & Ian Rogers.
7) Batch of fixes to the BPF selftest for xdp_hw_metadata which resulted
when testing on different NICs, from Jesper Dangaard Brouer.
8) Fix libbpf to better detect kernel version code on Debian, from Hao Xiang.
9) Extend libbpf to add an option for when the perf buffer should
wake up, from Jon Doron.
10) Follow-up fix on xdp_metadata selftest to just consume on TX
completion, from Stanislav Fomichev.
11) Extend the kfuncs.rst document with description on kfunc
lifecycle & stability expectations, from David Vernet.
12) Fix bpftool prog profile to skip attaching to offline CPUs,
from Tonghao Zhang.
====================
Link: https://lore.kernel.org/r/20230211002037.8489-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ajit Khaparde says:
====================
bnxt: Add Auxiliary driver support
Add auxiliary device driver for Broadcom devices.
The bnxt_en driver will register and initialize an aux device
if RDMA is enabled in the underlying device.
The bnxt_re driver will then probe and initialize the
RoCE interfaces with the infiniband stack.
We got rid of the bnxt_en_ops which the bnxt_re driver used to
communicate with bnxt_en.
Similarly We have tried to clean up most of the bnxt_ulp_ops.
In most of the cases we used the functions and entry points provided
by the auxiliary bus driver framework.
And now these are the minimal functions needed to support the functionality.
We will try to work on getting rid of the remaining if we find any
other viable option in future.
* 'aux-bus-v11' of https://github.com/ajitkhaparde1/linux:
bnxt_en: Remove runtime interrupt vector allocation
RDMA/bnxt_re: Remove the sriov config callback
bnxt_en: Remove struct bnxt access from RoCE driver
bnxt_en: Use auxiliary bus calls over proprietary calls
bnxt_en: Use direct API instead of indirection
bnxt_en: Remove usage of ulp_id
RDMA/bnxt_re: Use auxiliary driver interface
bnxt_en: Add auxiliary driver support
====================
Link: https://lore.kernel.org/r/20230202033809.3989-1-ajit.khaparde@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A summary of the flags being set for various drivers is given below.
Note that XDP_F_REDIRECT_TARGET and XDP_F_FRAG_TARGET are features
that can be turned off and on at runtime. This means that these flags
may be set and unset under RTNL lock protection by the driver. Hence,
READ_ONCE must be used by code loading the flag value.
Also, these flags are not used for synchronization against the availability
of XDP resources on a device. It is merely a hint, and hence the read
may race with the actual teardown of XDP resources on the device. This
may change in the future, e.g. operations taking a reference on the XDP
resources of the driver, and in turn inhibiting turning off this flag.
However, for now, it can only be used as a hint to check whether device
supports becoming a redirection target.
Turn 'hw-offload' feature flag on for:
- netronome (nfp)
- netdevsim.
Turn 'native' and 'zerocopy' features flags on for:
- intel (i40e, ice, ixgbe, igc)
- mellanox (mlx5).
- stmmac
- netronome (nfp)
Turn 'native' features flags on for:
- amazon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2, enetc)
- funeth
- intel (igb)
- marvell (mvneta, mvpp2, octeontx2)
- mellanox (mlx4)
- mtk_eth_soc
- qlogic (qede)
- sfc
- socionext (netsec)
- ti (cpsw)
- tap
- tsnep
- veth
- xen
- virtio_net.
Turn 'basic' (tx, pass, aborted and drop) features flags on for:
- netronome (nfp)
- cavium (thunder)
- hyperv.
Turn 'redirect_target' feature flag on for:
- amanzon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2)
- intel (i40e, ice, igb, ixgbe)
- ti (cpsw)
- marvell (mvneta, mvpp2)
- sfc
- socionext (netsec)
- qlogic (qede)
- mellanox (mlx5)
- tap
- veth
- virtio_net
- xen
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Co-developed-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Marek Majtyka <alardam@gmail.com>
Link: https://lore.kernel.org/r/3eca9fafb308462f7edb1f58e451d59209aa07eb.1675245258.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Modified the bnxt_en code to create and pre-configure RDMA devices
with the right MSI-X vector count for the ROCE driver to use.
This is to align the ROCE driver to the auxiliary device model which
will simply bind the driver without getting into PCI-related handling.
All PCI-related logic will now be in the bnxt_en driver.
Suggested-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Remove the SRIOV config callback which the bnxt_en was calling
to reconfigure the chip resources for a PF device when VFs are
created. The code is now modified to provision the VF resources
based on the total VF count instead of the actual VF count.
This allows the SRIOV config callback to be removed from the
list of ulp_ops.
Suggested-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Decouple RoCE driver from directly accessing L2's private bnxt
structure. Move the fields needed by RoCE driver into bnxt_en_dev.
They'll be passed to RoCE driver by bnxt_rdma_aux_device_add()
function.
Signed-off-by: Hongguang Gao <hongguang.gao@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Wherever possible use the function ops provided by auxiliary bus
instead of using proprietary ops.
Defined bnxt_re_suspend and bnxt_re_resume calls which can be
invoked by the bnxt_en driver instead of the ULP stop/start calls.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
For a single ULP user there is no need for complicating function
indirection calls. Remove all this complexity in favour of direct
function calls exported by the bnxt_en driver. This allows to
simplify the code greatly. Also remove unused ulp_async_notifier.
Suggested-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Since the driver continues to use the single ULP model,
the extra complexity and indirection is unnecessary.
Remove the usage of ulp_id from the code.
Suggested-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
