Current codebase contained the usage of two different names for this
driver (i.e., `gvnic` and `gve`), which is quite unfriendly for users
to use, especially when trying to bind or unbind the driver manually.
The corresponding kernel module is registered with the name of `gve`.
It's more reasonable to align the name of the driver with the module.
Fixes: 893ce44df5 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Cc: csully@google.com
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for using IPv6 Big TCP on DQ which can handle large TSO/GRO
packets. See https://lwn.net/Articles/895398/. This can improve the
throughput and CPU usage.
Perf test result:
ip -d link show $DEV
gso_max_size 185000 gso_max_segs 65535 tso_max_size 262143 tso_max_segs 65535 gro_max_size 185000
For performance, tested with neper using 9k MTU on hardware that supports 200Gb/s line rate.
In single streams when line rate is not saturated, we expect throughput improvements.
When the networking is performing at line rate, we expect cpu usage improvements.
Tcp_stream (unidirectional stream test, T=thread, F=flow):
skb=180kb, T=1, F=1, no zerocopy: throughput average=64576.88 Mb/s, sender stime=8.3, receiver stime=10.68
skb=64kb, T=1, F=1, no zerocopy: throughput average=64862.54 Mb/s, sender stime=9.96, receiver stime=12.67
skb=180kb, T=1, F=1, yes zerocopy: throughput average=146604.97 Mb/s, sender stime=10.61, receiver stime=5.52
skb=64kb, T=1, F=1, yes zerocopy: throughput average=131357.78 Mb/s, sender stime=12.11, receiver stime=12.25
skb=180kb, T=20, F=100, no zerocopy: throughput average=182411.37 Mb/s, sender stime=41.62, receiver stime=79.4
skb=64kb, T=20, F=100, no zerocopy: throughput average=182892.02 Mb/s, sender stime=57.39, receiver stime=72.69
skb=180kb, T=20, F=100, yes zerocopy: throughput average=182337.65 Mb/s, sender stime=27.94, receiver stime=39.7
skb=64kb, T=20, F=100, yes zerocopy: throughput average=182144.20 Mb/s, sender stime=47.06, receiver stime=39.01
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230522201552.3585421-1-ziweixiao@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clearing the PBA bit from the driver is race prone and it may lead to
dropped interrupt events. This could potentially lead to the traffic
being completely halted.
Fixes: 5e8c5adf95 ("gve: DQO: Add core netdev features")
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding AF_XDP zero-copy support.
Note: Although these changes support AF_XDP socket in zero-copy
mode, there is still a copy happening within the driver between
XSK buffer pool and QPL bounce buffers in GQI-QPL format.
In GQI-QPL queue format, the driver needs to allocate a fixed size
memory, the size specified by vNIC device, for RX/TX and register this
memory as a bounce buffer with the vNIC device when a queue is
created. The number of pages in the bounce buffer is limited and the
pages need to be made available to the vNIC by copying the RX data out
to prevent head-of-line blocking. Therefore, we cannot pass the XSK
buffer pool to the vNIC.
The number of copies on RX path from the bounce buffer to XSK buffer is 2
for AF_XDP copy mode (bounce buffer -> allocated page frag -> XSK buffer)
and 1 for AF_XDP zero-copy mode (bounce buffer -> XSK buffer).
This patch contains the following changes:
1) Enable and disable XSK buffer pool
2) Copy XDP packets from QPL bounce buffers to XSK buffer on rx
3) Copy XDP packets from XSK buffer to QPL bounce buffers and
ring the doorbell as part of XDP TX napi poll
4) ndo_xsk_wakeup callback support
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the following changes:
1) Support for XDP REDIRECT action on rx
2) ndo_xdp_xmit callback support
In GQI-QPL queue format, the driver needs to allocate a fixed size
memory, the size specified by vNIC device, for RX/TX and register this
memory as a bounce buffer with the vNIC device when a queue is created.
The number of pages in the bounce buffer is limited and the pages need to
be made available to the vNIC by copying the RX data out to prevent
head-of-line blocking. The XDP_REDIRECT packets are therefore immediately
copied to a newly allocated page.
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for XDP PASS, DROP and TX actions.
This patch contains the following changes:
1) Support installing/uninstalling XDP program
2) Add dedicated XDP TX queues
3) Add support for XDP DROP action
4) Add support for XDP TX action
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to enable adding and removing TX queues without calling
gve_close() and gve_open().
Made the following changes:
1) priv->tx, priv->rx and priv->qpls arrays are allocated based on
max tx queues and max rx queues
2) Changed gve_adminq_create_tx_queues(), gve_adminq_destroy_tx_queues(),
gve_tx_alloc_rings() and gve_tx_free_rings() functions to add/remove a
subset of TX queues rather than all the TX queues.
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds/modifies helper functions needed to add XDP
support.
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQs are currently requested before the netdevice is registered
and a proper name is assigned to the device. Changing interrupt
name to avoid using the format string in the name.
Interrupt name before change: eth%d-ntfy-block.<blk_id>
Interrupt name after change: gve-ntfy-blk<blk_id>@pci:<pci_name>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether the driver is compatible with the device
presented.
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On 32bit-UP u64_stats_fetch_begin() disables only preemption. If the
reader is in preemptible context and the writer side
(u64_stats_update_begin*()) runs in an interrupt context (IRQ or
softirq) then the writer can update the stats during the read operation.
This update remains undetected.
Use u64_stats_fetch_begin_irq() to ensure the stats fetch on 32bit-UP
are not interrupted by a writer. 32bit-SMP remains unaffected by this
change.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Catherine Sullivan <csully@google.com>
Cc: David Awogbemila <awogbemila@google.com>
Cc: Dimitris Michailidis <dmichail@fungible.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jeroen de Borst <jeroendb@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Simon Horman <simon.horman@corigine.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: oss-drivers@corigine.com
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit
a5886ef4f4 ("gve: Introduce per netdev `enum gve_queue_format`")
introduces three queue format type, only GVE_GQI_QPL_FORMAT queue has
page list. So it should use the queue page list number to detect the
zero size queue page list. Correct the design logic.
Using the 'queue_format == GVE_GQI_RDA_FORMAT' may lead to request zero
sized memory allocation, like if the queue format is GVE_DQO_RDA_FORMAT.
The kernel memory subsystem will return ZERO_SIZE_PTR, which is not NULL
address, so the driver can run successfully. Also the code still checks
the queue page list number firstly, then accesses the allocated memory,
so zero number queue page list allocation will not lead to access fault.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Reviewed-by: Bailey Forrest <bcf@google.com>
Link: https://lore.kernel.org/r/20220215051751.260866-1-haiyue.wang@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use GFP_ATOMIC when allocating pages out of the hotpath,
continue to use GFP_KERNEL when allocating pages during setup.
GFP_KERNEL will allow blocking which allows it to succeed
more often in a low memory enviornment but in the hotpath we do
not want to allow the allocation to block.
Fixes: f5cedc84a3 ("gve: Add transmit and receive support")
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Link: https://lore.kernel.org/r/20220126003843.3584521-1-awogbemila@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adding ethtool support for changing rx-coalesce-usec and tx-coalesce-usec
when using the DQO queue format.
Signed-off-by: Tao Liu <xliutaox@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for suspend, resume and shutdown.
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The id field should be a u32 not a signed int.
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Giving the device access to other kernel structs is not ideal.
Move the indexes into their own array and just keep pointers to
them in the ntfy block struct.
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The priv->ntfy_blocks[] has "priv->num_ntfy_blks" elements so this >
needs to be >= to prevent an off by one bug. The priv->ntfy_blocks[]
array is allocated in gve_alloc_notify_blocks().
Fixes: 87a7f321bb ("gve: Recover from queue stall due to missed IRQ")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables the driver to receive RX packets spread across multiple
buffers:
For a given multi-fragment packet the "packet continuation" bit is set
on all descriptors except the last one. These descriptors' payloads are
combined into a single SKB before the SKB is handed to the
networking stack.
This change adds a "packet buffer size" notion for RX queues. The
CreateRxQueue AdminQueue command sent to the device now includes the
packet_buffer_size.
We opt for a packet_buffer_size of PAGE_SIZE / 2 to give the
driver the opportunity to flip pages where we can instead of copying.
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't always reset the driver on a TX timeout. Attempt to
recover by kicking the queue in case an IRQ was missed.
Fixes: 9e5f7d26a4 ("gve: Add workqueue and reset support")
Signed-off-by: John Fraker <jfraker@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TX queue is full, attemt to process enough TX completions
to avoid stalling the queue.
Fixes: f5cedc84a3 ("gve: Add transmit and receive support")
Signed-off-by: Tao Liu <xliutaox@google.com>
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done to allow for the use of gro_flush_timeout.
Fixes: f5cedc84a3 ("gve: Add transmit and receive support")
Signed-off-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each tx queue maintains a 64bit counter for bytes, there is
no reason to truncate this to 32bit (or this has not been
documented)
Fixes: 24aeb56f2d ("gve: Add Gvnic stats AQ command and ethtool show/set-priv-flags.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yangchun Fu <yangchun@google.com>
Cc: Kuo Zhao <kuozhao@google.com>
Cc: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gve_get_stats() can report wrong numbers if/when u64_stats_fetch_retry()
returns true.
What is needed here is to sample values in temporary variables,
and only use them after each loop is ended.
Fixes: f5cedc84a3 ("gve: Add transmit and receive support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Catherine Sullivan <csully@google.com>
Cc: Sagi Shahar <sagis@google.com>
Cc: Jon Olson <jonolson@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Luigi Rizzo <lrizzo@google.com>
Cc: Jeroen de Borst <jeroendb@google.com>
Cc: Tao Liu <xliutaox@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent possible crashes when cleaning up after unsuccessful
initializations.
Fixes: 893ce44df5 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Signed-off-by: Tao Liu <xliutaox@google.com>
Signed-off-by: Catherine Sully <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 2-factor argument form kvcalloc() instead of kvzalloc().
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrappers in include/linux/pci-dma-compat.h should go away.
Replace 'pci_set_dma_mask/pci_set_consistent_dma_mask' by an equivalent
and less verbose 'dma_set_mask_and_coherent()' call.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'gve_probe()' fails, we should propagate the error code, instead of
hard coding a -ENXIO value.
Make sure that all error handling paths set a correct value for 'err'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the 'register_netdev() call fails, we must release the resources
allocated by the previous 'gve_init_priv()' call, as already done in the
remove function.
Add a new label and the missing 'gve_teardown_priv_resources()' in the
error handling path.
Fixes: 893ce44df5 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in net/netfilter/nf_tables_api.c.
Duplicate fix in tools/testing/selftests/net/devlink_port_split.py
- take the net-next version.
skmsg, and L4 bpf - keep the bpf code but remove the flags
and err params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
https://patchwork.kernel.org/project/netdevbpf/list/?series=506637&state=*
- Remove unused variable
- Use correct integer type for string formatting.
- Remove `inline` in C files
Fixes: 9c1a59a2f4 ("gve: DQO: Add ring allocation and initialization")
Fixes: a57e5de476 ("gve: DQO: Add TX path")
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When interrupts are first enabled, we also set the ratelimits, which
will be static for the entire usage of the device.
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate the buffer and completion ring structures. Do not populate the
rings yet. That will happen in the respective rx and tx datapath
follow-on patches
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add napi netdev device registration, interrupt handling and initial tx
and rx polling stubs. The stubs will be filled in follow-on patches.
Also:
- LRO feature advertisement and handling
- Also update ethtool logic
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike GQI, DQO RX descriptors do not contain the L3 and L4 type of the
packet. L3 and L4 types are necessary in order to set the hash and csum
on RX SKBs correctly.
DQO RX descriptors instead contain a 10 bit PTYPE index. The PTYPE map
enables the device to tell the driver how to map from PTYPE index to
L3/L4 type.
The device doesn't provide any guarantees about the range of possible
PTYPEs, so we just use a 1024 entry array to implement a fast mapping
structure.
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The currently supported queue formats are:
- GQI_RDA - GQI with raw DMA addressing
- GQI_QPL - GQI with queue page list
- DQO_RDA - DQO with raw DMA addressing
The old `gve_priv.raw_addressing` value is only used for GQI_RDA, so we
remove it in favor of just checking against GQI_RDA
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As currently written, if the driver checks for more work (via
gve_tx_poll or gve_rx_poll) before the device posts work and the
irq doorbell is not unmasked
(via iowrite32be(GVE_IRQ_ACK | GVE_IRQ_EVENT, ...)) before the device
attempts to raise an interrupt, an interrupt is lost and this could
potentially lead to the traffic being completely halted. For
example, if a tx queue has already been stopped, the driver won't get
the chance to complete work and egress will be halted.
We need a full memory barrier in the poll
routine to ensure that the irq doorbell is unmasked before the driver
checks for more work.
Fixes: f5cedc84a3 ("gve: Add transmit and receive support")
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Acked-by: Willem de Brujin <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When freeing notification blocks, we index priv->msix_vectors.
If we failed to allocate priv->msix_vectors (see abort_with_msix_vectors)
this could lead to a NULL pointer dereference if the driver is unloaded.
Fixes: 893ce44df5 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Signed-off-by: David Awogbemila <awogbemila@google.com>
Acked-by: Willem de Brujin <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we do not get the expected number of vectors from
pci_enable_msix_range, we update priv->num_ntfy_blks but not
priv->mgmt_msix_idx. This patch fixes this so that priv->mgmt_msix_idx
is updated accordingly.
Fixes: f5cedc84a3 ("gve: Add transmit and receive support")
Signed-off-by: David Awogbemila <awogbemila@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to use raw dma addresses in the rx path. Due to this new
support we can alloc a new buffer instead of making a copy.
RX buffers are handed to the networking stack and are
re-allocated as needed, avoiding the need to use
skb_copy_to_linear_data() as in "qpl" mode.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to describe device for parsing device options. As
the first device option, add raw addressing.
"Raw Addressing" mode (as opposed to the current "qpl" mode) is an
operational mode which allows the driver avoid bounce buffer copies
which it currently performs using pre-allocated qpls (queue_page_lists)
when sending and receiving packets.
For egress packets, the provided skb data addresses will be dma_map'ed and
passed to the device, allowing the NIC can perform DMA directly - the
driver will not have to copy the buffer content into pre-allocated
buffers/qpls (as in qpl mode).
For ingress packets, copies are also eliminated as buffers are handed to
the networking stack and then recycled or re-allocated as
necessary, avoiding the use of skb_copy_to_linear_data().
This patch only introduces the option to the driver.
Subsequent patches will add the ingress and egress functionality.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The
older style of one-element or zero-length arrays should no longer be
used[2].
Refactor the code according to the use of a flexible-array member in
struct gve_stats_report, instead of a zero-length array, and use the
struct_size() helper to calculate the size for the resource allocation.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9/process/deprecated.html#zero-length-and-one-element-arrays
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
This makes the driver better aware of the connectivity status of the
device. Based on the device's status register, the driver can call
netif_carrier_{on,off}.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Patricio Noyola <patricion@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for batching AQ commands and uses it for creating and
destroying queues.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds per queue NIC stats to ethtool stats and to report-stats.
These stats are always exposed to guest whether or not the
report-stats flag is turned on.
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds functionality to report driver stats to Hypervisor.
(Users may want to turn this feature off as a matter of privacy
so a "report-stats" flag is added as an ethtool priv option.
It is also disabled by default.)
The hypervisor would trigger a stats report in case "too many"
packets dropped; the stats would be useful in debugging stuck
queues.
A "stats_report_trigger_cnt" stat is added to count the number of times
the hypervisor attempts to trigger stats report.
A timer is also added so that when report-stats is enabled, stat are
updated once every 20 seconds.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Kuo Zhao <kuozhao@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
