Here is the big set of char/misc driver changes for 5.15-rc1.
Lots of different driver subsystems are being updated in here, notably:
- mhi subsystem update
- fpga subsystem update
- coresight/hwtracing subsystem update
- interconnect subsystem update
- nvmem subsystem update
- parport drivers update
- phy subsystem update
- soundwire subsystem update
and there are some other char/misc drivers being updated as well:
- binder driver additions
- new misc drivers
- lkdtm driver updates
- mei driver updates
- sram driver updates
- other minor driver updates.
Note, there are no habanna labs driver updates in this pull request,
that will probably come later before -rc1 is out in a different request.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+Kyw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymlpACg0JM+hSeo8T5GtwZksZ1QXXQfh8sAoK6Dt6xF
e62OQuuMFT0Un0qOflZk
=emH+
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big set of char/misc driver changes for 5.15-rc1.
Lots of different driver subsystems are being updated in here,
notably:
- mhi subsystem update
- fpga subsystem update
- coresight/hwtracing subsystem update
- interconnect subsystem update
- nvmem subsystem update
- parport drivers update
- phy subsystem update
- soundwire subsystem update
and there are some other char/misc drivers being updated as well:
- binder driver additions
- new misc drivers
- lkdtm driver updates
- mei driver updates
- sram driver updates
- other minor driver updates.
Note, there are no habanalabs driver updates in this pull request,
that will probably come later before -rc1 is out in a different
request.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (169 commits)
Revert "bus: mhi: Add inbound buffers allocation flag"
misc/pvpanic: fix set driver data
VMCI: fix NULL pointer dereference when unmapping queue pair
char: mware: fix returnvar.cocci warnings
parport: remove non-zero check on count
soundwire: cadence: do not extend reset delay
soundwire: intel: conditionally exit clock stop mode on system suspend
soundwire: intel: skip suspend/resume/wake when link was not started
soundwire: intel: fix potential race condition during power down
phy: qcom-qmp: Add support for SM6115 UFS phy
dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings
phy: qmp: Provide unique clock names for DP clocks
lkdtm: remove IDE_CORE_CP crashpoint
lkdtm: replace SCSI_DISPATCH_CMD with SCSI_QUEUE_RQ
coresight: Replace deprecated CPU-hotplug functions.
Documentation: coresight: Add documentation for CoreSight config
coresight: syscfg: Add initial configfs support
coresight: config: Add preloaded configurations
coresight: etm4x: Add complex configuration handlers to etmv4
coresight: etm-perf: Update to activate selected configuration
...
MHI driver requires register space length to add range checks and
prevent memory region accesses outside of that for MMIO space.
Set it before registering the MHI controller.
Link: https://lore.kernel.org/r/1620330705-40192-5-git-send-email-bbhatt@codeaurora.org
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210802051255.5771-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring array fields.
Since peer_he_cap_{mac,phy}info and he_cap_elem.{mac,phy}_cap_info are not
the same sizes, memcpy() was reading beyond field boundaries. Instead,
correctly cap the copy length and pad out any difference in size
(peer_he_cap_macinfo is 8 bytes whereas mac_cap_info is 6, and
peer_he_cap_phyinfo is 12 bytes whereas phy_cap_info is 11).
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210616195410.1232119-1-keescook@chromium.org
Firmware has added assert if beacon template is received after
vdev_down. Firmware expects beacon template after vdev_start
and before vdev_up. This change is needed to support MBSSID EMA
cases in firmware.
Hence, Change the sequence in ath11k as expected from firmware.
This new change is not causing any issues with older
firmware.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1.r3-00011-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1.r4-00008-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
[sven@narfation.org: added tested-on/fixes information]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210525133028.2805615-1-sven@narfation.org
For QCA6390, one PCI related clock drifts sometimes, and it makes
PCI link difficult to quit L1ss. Current implementation fixed this
by configuring some related regs using ath11k_pci_fix_l1ss.
WCN6855 does not have this clock drift problem, so no need to set
these regs.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-8-jouni@codeaurora.org
This patch is to add support for WCN6855. For station mode,
WCN6855 is able to connect to an AP, and ping works well.
For AP mode, hostapd is able to bringup an SAP interface with
WCN6855, a normal station can connect to this AP and
ping works well.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-7-jouni@codeaurora.org
For WCN6855, the layout of hal rx mpdu info is different, so need to
handle this target differently when getting peer id.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-6-jouni@codeaurora.org
For WCN6855, WBM idle link ring needs a reinit.
Without this reinit, firmware crash might happen occasionally.
This is requested by the hw team.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-5-jouni@codeaurora.org
WCN6855 needs a different reo configuration, so add separate handling
for this target in ath11k_hw_ops.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-4-jouni@codeaurora.org
hal rx descriptor is different for WCN6855 and there are such a lot
of handlers processing this descriptor in data path. So add separate
handling for this target.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-3-jouni@codeaurora.org
Reg address of WCN6855 is different from other devices,
so add separate reg definition for this target.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-2-jouni@codeaurora.org
There are multiple occurrances of the misspelling of requeued in
the drivers with symbol names and debug text. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210423134133.339751-1-colin.king@canonical.com
Currently the fragment cache setup during peer assoc is
cleared only during peer delete. In case a key reinstallation
happens with the same peer, the same fragment cache with old
fragments added before key installation could be clubbed
with fragments received after. This might be exploited
to mix fragments of different data resulting in a proper
unintended reassembled packet to be passed up the stack.
Hence flush the fragment cache on every key installation to prevent
potential attacks (CVE-2020-24587).
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Cc: stable@vger.kernel.org
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.218dc777836f.I9af6fc76215a35936c4152552018afb5079c5d8c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* set sk_pacing_shift for 802.3->802.11 encap offload
* some monitor support for 802.11->802.3 decap offload
* HE (802.11ax) spec updates
* userspace API for TDLS HE support
* along with various other small features, cleanups and
fixups
-----BEGIN PGP SIGNATURE-----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=b0NQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-04-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of updates, all over the map:
* set sk_pacing_shift for 802.3->802.11 encap offload
* some monitor support for 802.11->802.3 decap offload
* HE (802.11ax) spec updates
* userspace API for TDLS HE support
* along with various other small features, cleanups and
fixups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for v5.13. Major changes:
ath11k
* add initial support for QCN9074, but not enabled yet due to firmware problems
* enable radar detection for 160MHz secondary segment
* handle beacon misses in station mode
When AP goes down without any indication to STA, firmware detects
missing beacon, and sends wmi roam event with reason BEACON_MISS
to the host.
Added support for STA mode to trigger disassociation from AP,
on receiving this event from firmware.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01717-QCAHKSWPL_SILICONZ-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1614340859-28867-1-git-send-email-lavaks@codeaurora.org
Currently, though the peer rssi information is updated to station dump
from driver sta_statistics mac op, the info doesn't get updated
since the NL80211_STA_INFO_SIGNAL filled flag is not set in station
info. Hence update this flag while filling the rssi info.
Tested on: IPQ8074 WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210224090241.3098-1-srirrama@codeaurora.org
Fix dangling pointer in thermal temperature event which causes
incorrect temperature read.
Tested-on: IPQ8074 AHB WLAN.HK.2.4.0.1-00041-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210218182708.8844-1-pradeepc@codeaurora.org
Commit c134d1f8c4 ("ath11k: Handle errors if peer creation fails") completely
broke AP mode on QCA6390:
kernel: [ 151.230734] ath11k_pci 0000:06:00.0: failed to create peer after vdev start delay: -22
wpa_supplicant[2307]: Failed to set beacon parameters
wpa_supplicant[2307]: Interface initialization failed
wpa_supplicant[2307]: wlan0: interface state UNINITIALIZED->DISABLED
wpa_supplicant[2307]: wlan0: AP-DISABLED
wpa_supplicant[2307]: wlan0: Unable to setup interface.
wpa_supplicant[2307]: Failed to initialize AP interface
This was because commit c134d1f8c4 ("ath11k: Handle errors if peer creation
fails") added error handling for ath11k_peer_create(), which had been failing
all along but was unnoticed due to the missing error handling. The actual bug
was introduced already in commit aa44b2f3ec ("ath11k: start vdev if a bss peer is
already created").
ath11k_peer_create() was failing because for AP mode the peer is created
already earlier op_add_interface() and we should skip creation here, but the
check for modes was wrong. Fixing that makes AP mode work again.
This shouldn't affect IPQ8074 nor QCN9074 as they have hw_params.vdev_start_delay disabled.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Fixes: c134d1f8c4 ("ath11k: Handle errors if peer creation fails")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1614006849-25764-1-git-send-email-kvalo@codeaurora.org
If CONFIG_ARCH_DMA_ADDR_T_64BIT=n:
drivers/net/wireless/ath/ath11k/qmi.c: In function ‘ath11k_qmi_respond_fw_mem_request’:
drivers/net/wireless/ath/ath11k/qmi.c:1690:8: warning: format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 5 has type ‘dma_addr_t’ {aka ‘unsigned int’} [-Wformat=]
1690 | "qmi req mem_seg[%d] 0x%llx %u %u\n", i,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1691 | ab->qmi.target_mem[i].paddr,
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
| |
| dma_addr_t {aka unsigned int}
drivers/net/wireless/ath/ath11k/debug.h:64:30: note: in definition of macro ‘ath11k_dbg’
64 | __ath11k_dbg(ar, dbg_mask, fmt, ##__VA_ARGS__); \
| ^~~
drivers/net/wireless/ath/ath11k/qmi.c:1690:34: note: format string is defined here
1690 | "qmi req mem_seg[%d] 0x%llx %u %u\n", i,
| ~~~^
| |
| long long unsigned int
| %x
Fixes: d5395a5486 ("ath11k: qmi: add debug message for allocated memory segment addresses and sizes")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210221182754.2071863-1-geert@linux-m68k.org
WMI_CHAN_INFO_DFS_FREQ2 needs to be set in wmi vdev start command chan
info parameter, to enable radar detection for secondary segment in 160MHz.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01717-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1613480547-28810-1-git-send-email-lavaks@codeaurora.org
Number of Sounding dimensions config received from firmware for
bandwidth above 80MHz is cleared, and proper value is not set again.
So not resetting it to accept the config from firmware.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01689-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1613460136-7170-1-git-send-email-lavaks@codeaurora.org
QCN9074 is PCI based 11ax radio.
- has 2G/5G/6G variants.
- has NSS 2x2 and 4x4 variants.
QCN9074 uses 45MB of HOST DDR memory, target requests host memory in
segments, each segment is of 2MB size and is physcial contiguous and
use static window configuration.
Currently there are still two issues with QCN9074, see below. So we don't add
QCN9074 PCI id yet to make sure the driver is loaded. The id will be added only
after the issues are fixed.
Issue 1:
ath11k_pci 0000:06:00.0: qmi failed memory request, err = -110
ath11k_pci 0000:06:00.0: qmi failed to respond fw mem req:-110
Issue 2:
ath11k_pci 0000:06:00.0: firmware crashed: MHI_CB_SYS_ERROR
ath11k_pci 0000:06:00.0: qmi failed set mode request, mode: 0, err = -110
ath11k_pci 0000:06:00.0: qmi failed to send wlan fw mode:-110
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-12-git-send-email-akolli@codeaurora.org
Update the specific hw ring mask for QCN9074. Update the timestamp
information while processing DP and CE interrupts.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-11-git-send-email-akolli@codeaurora.org
Define host CE configuration for QCN9074 since the max CE count is six.
Available MSI interrupt is five so cannot able to map the ce_id directly
for the msi_data_idx. Added get_ce_msi_idx ops in ath11k_hif_ops to get
the CE MSI idx which is used to initialize the CE ring.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-10-git-send-email-akolli@codeaurora.org
hal rx descriptor is different for QCN9074 target type. since
rx_msdu_end, rx_msdu_start, rx_mpdu_start elements are in
different placement/alignment. In order to have generic data path,
introduce platform specific hal rx descriptor access ops in
ath11k_hw_ops.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-9-git-send-email-akolli@codeaurora.org
Define the hal ring address and ring meta descriptor mask for
QCN9074. Move the platform specific address to the ath11k_hw_regs.
Define tx_mesh_enable ops in ath11k_hw_ops since its accessing
platform specific TCL descriptor.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-8-git-send-email-akolli@codeaurora.org
Three window slots can be configure. First window slot
dedicate for dynamic selection and remaining two slots
dedicate for static selection. To optimise the window
selection, frequent registers (UMAC, CE) are configure
in static window slot. so that we minimise the window
selection. Other registers are configure in dynamic window
slot. Get the window start address from the respective
offset and access the read/write register.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-7-git-send-email-akolli@codeaurora.org
Add MHI config for QCN9074 also populate ath11k_hw_params for QCN9074.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-6-git-send-email-akolli@codeaurora.org
QCN9074 FW requests three types memory segments during the boot,
qmi mem seg type 1 of size 15728640
qmi mem seg type 4 of size 3735552
qmi mem seg type 3 of size 1048576
Segment type 3 is for M3 coredump memory.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-5-git-send-email-akolli@codeaurora.org
QCN9074 firmware uses 20MB of HOST DDR memory, fw requests
the memory in segmnets of size 1MB/512KB/256KB.
Increase the number of fw memory segments to 52.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-4-git-send-email-akolli@codeaurora.org
qmi service_ins_id is unique for QCA6390 and QCN9074,
this is needed for adding QCN9074 support. No functional
changes.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-3-git-send-email-akolli@codeaurora.org
Move ath11k_msi_config to array of structures to add multiple
pci devices support. No functional changes.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-2-git-send-email-akolli@codeaurora.org
I have received feedback that QCA6390 PCI support is working for many, and I'm
also using QCA6390 on my daily driver^Hlaptop. While there are issues still
to be resolved it's not really experimental anymore, so remove the experimental
warning from driver initialisation.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1613040697-20289-1-git-send-email-kvalo@codeaurora.org
