Due to a rebase damage, we lost the rtnl_lock() when the patch was
sent out. This causes an RTNL imbalance and failed assertions, due to
missing RTNL protection, for instance:
RTNL: assertion failed at net/wireless/reg.c (4025)
WARNING: CPU: 60 PID: 1720 at net/wireless/reg.c:4025 regulatory_set_wiphy_regd_sync+0x7f/0x90 [cfg80211]
Call Trace:
iwl_mvm_init_mcc+0x170/0x190 [iwlmvm]
iwl_op_mode_mvm_start+0x824/0xa60 [iwlmvm]
iwl_opmode_register+0xd0/0x130 [iwlwifi]
init_module+0x23/0x1000 [iwlmvm]
Fix this by adding the missing rtnl_lock() back to the code.
Fixes: eb09ae93da ("iwlwifi: mvm: load regdomain at INIT stage")
Link: https://lore.kernel.org/lkml/CAHk-=wjB_zBwZ+WR9LOpvgjvaQn=cqryoKigod8QnZs=iYGEhA@mail.gmail.com/
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To check beacon protection had a mismatch of the key ID we
currently use the key ID from the firmware, but firmware
side we want to clean up the API to stop reporting this.
Instead, check the IWL_RX_MPDU_STATUS_KEY_VALID bit that
indicates that the firmware used the correct key, and if
that's set but we get invalid MIC/replay use the key ID
from the frame to look up the key and notify mac80211 of
MIC error or replay. Since both keys must have the same
cipher and thus MIC length, we can use either of them to
look up the MIC length.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210826224715.30e665d39b07.I78bf7d304ef5a80cecf5fa1c1fca0b51b956cceb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This version adds the following configuration options:
1. Enable/disable setting the session id in the FTM frame
2. Set the BSS color for the responder
3. Set the minimum and maximum time between measurements for
non trigger based NDP ranging.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210826224715.0a10d43f3d7f.Ice4112c1910cf94babd1c2d492a3a3de9f7ee6cb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This version adds the following configuration options:
1. Set the BSS color for NDP ranging
2. Set the minimum and maximum time between measurements for
non trigger based NDP ranging.
3. Terminate the session in case the responder requests LMR feedback.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210826224715.9dcd5210b7e5.I76f6977cde852de0f251344e279ad85076eef8d6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When P2P roc is removed, the IWL_MVM_STATUS_NEED_FLUSH_P2P bit is set
to indicate to iwl_mvm_roc_done_wk() that the removed roc is a P2P
one, so it will flush the broadcast station and not the aux station.
However, since setting this bit and scheduling the worker is done
in roc ended flow as well as in case the roc is removed, there is
a race where the worker has already started running (but did not
test this bit yet) and then it is scheduled again. In this case,
the first run of the worker will clear this bit, and thus the second
run will find it already cleared and will try to flush and remove
the aux station by mistake.
Fix it by scheduling the worker only if this bit is not yet set. In
case this bit is already set, the worker is either running or
scheduled, so there is no need to re-schedule it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210819183728.8c147659b331.If5924375e9bfd46214ab8ab81cb9d0f5c82fbcbc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We used to load the regdomain only in the load stage,
this caused the 'iw phy phy0 reg get' command to fail if we
booted a machine with wifi off.
Therefor we should load it in INIT stage already.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.a6077801d7d5.I7d8d5c895bc467efbf81ea055dde366ea01cced1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We used to read the PPAG, WRDS, EWRD, WGDS tables from ACPI
in the load stage only. This prevented vendor commands from
being executed before bringing the interface up. Move reading those tables
to INIT stage.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.ce3b60f0b426.I3643bf00e714aae930880cc7d6cf390b142eaccb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new version of the command has same size and layout as
version 10. It just sends corresponding station id in one
of the reserved fields. It's not used in the driver, so just
be ready to accept version 11.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.0a387598eef1.I3be0bbf603ef95c644218be8a12b329411f11646@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The GEO profiles have been stored in single-dimension arrays and the
access has been done via a single index. We will soon need to support
different revisions of this table, which will make the flat array even
harder to handle. To prepare for that, convert the single-dimension
array to a struct with substructures.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.56f3506411a2.I600ed3708d19f2263a5a8d143f6711d08499bbb0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This definition was only used to pass the size of the tables in the FW
API to the iwl_sar_select_profile() function, but we should actually
pass the definition from the FW API file. We don't have the concept
of tables in the ACPI definition, so we can remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805130823.00b5084be918.I18efb3c45bffacfa9a356c2c8d34e5ffbb3eb423@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
- Short SSIDs should always be added for direct SSIDs included
in the scan request. However, this was not done in case that
information for collocated APs was included. Fix this.
- With the above fix, if the FW also supports discovery of hidden
APs over the 6GHz band, also set the corresponding full SSID
information.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805130823.02512b7a1443.Ibb023b09b86179ed049a195f4e32e887c2f4971d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a station is removed, the driver-mac80211 station mapping is removed
before the station is actually deleted from the FW. As a result, it is
reasonable that the FW will continue to pass frames although the driver
doesn't have a station for them anymore. Thus change the message
severity level from ERR to DEBUG_DROP.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805130823.a751177743c6.I5607504dade88ba461508643f58390dd661c05ba@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In later firmware we haven't needed the TSC anyway since
we have it already (and firmware image doesn't change),
but the new version adds the ability to send down replay
counters for more than one GTK. Implement that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805130823.28cd065e8c4a.Ic8406a78ee46b07e0ca1b8199522ef08ec6eef53@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that only reprogramming is left in the initial key iteration,
skip it entirely on unified firmware images instead of skipping
only the command sending inside of it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805130823.c6f77325c430.I798ce9d757492a9e3d223c1de5d4e62ebbc00b2c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we're sending the KEK/KCK data we also need the GTK and
IGTK type, add a separate key iteration for that so we can
make the configure_key iteration optional later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805130823.c99f86423702.Icf7d4e93be77ea05a80235d01851ad0155593de9@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We do a key iteration to program the keys, and while at it
we also collect the data necessary for TKIP. This code has
all kinds of dependencies on the firmware API though, so
take out the TKIP phase 1 key generation and do that in a
separate key iteration only if necessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805130823.80721fc0fd61.I5a8fbba4e3a9606f700ee41c7a4244dd5e2af935@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need for all the complicated conditions here, any
bufferable MMPDUs or MMPDUs for client interfaces are already
coming through the TXQ interface, not iwl_mvm_mac_tx().
Simplify the logic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.3939f7c5c43a.I1d5cb5262e31a000023d79acbb897b8db50adf0d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since switching to mac80211 TXQs, we no longer need to
advertise more hardware queues than ACs, since we don't
even set QUEUE_CONTROL anyway, so the vif->hw_queue[]
mapping array won't be used.
All we need (at least for now) is for hw->queues to
indicate that we have enough queues to handle QoS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.80611a3c1ee7.I8a3d2b269421b6d8bada8c12cce3e095e6cfaeed@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When TVQM is enabled (iwl_mvm_has_new_tx_api() is true), then
queue numbers are just sequentially assigned 0, 1, 2, ...
Prior to TVQM, in DQA, there were some statically allocated
queue numbers:
* IWL_MVM_DQA_AUX_QUEUE == 1,
* both IWL_MVM_DQA_INJECT_MONITOR_QUEUE and
IWL_MVM_DQA_P2P_DEVICE_QUEUE == 2, and
* IWL_MVM_DQA_AP_PROBE_RESP_QUEUE == 9.
Now, these values are assigned to the members mvm->aux_queue,
mvm->snif_queue, mvm->probe_queue and mvm->p2p_dev_queue by
default. Normally, this doesn't really matter, and if TVQM is
in fact available we override them to the real values after
allocating a queue for use there.
However, this allocation doesn't always happen. For example,
for mvm->p2p_dev_queue (== 2) it only happens when the P2P
Device interface is started, if any. If it's not started, the
value in mvm->p2p_dev_queue remains 2. This wouldn't really
matter all that much if it weren't for iwl_mvm_is_static_queue()
which checks a queue number against one of those four static
numbers.
Now, if no P2P Device or monitor interface is added then queue
2 may be dynamically allocated, yet alias mvm->p2p_dev_queue or
mvm->snif_queue, and thus iwl_mvm_is_static_queue() erroneously
returns true for it. If it then gets full, all interface queues
are stopped, instead of just backpressuring against the one TXQ
that's really the only affected one.
This clearly can lead to issues, as everything is stopped even
if just a single TXQ filled its corresponding HW queue, if it
happens to have an appropriate number (2 or 9, AUX is always
reassigned.) Due to a mac80211 bug, this also led to a situation
in which the queues remained stopped across a deauthentication
and then attempts to connect to a new AP started failing, but
that's fixed separately.
Fix all of this by simply initializing the queue numbers to
the invalid value until they're used, if TVQM is enabled, and
also setting them back to that value when the queues are later
freed again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.2e47e623f9e2.I9b0830dafbb68ef35b7b8f0f46160abec02ac7d0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware SMPS request should only be honoured if the
connection is currently with HE and on 160 MHz, so check
that and then potentially reapply any request if the BW
changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.0cdcac5660da.I9ee7956fd4f48399855d1f97728bc58b36caf112@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When installing a (new) key, set the replay counter so that
after FW restart the firmware has the correct value of the
replay counters.
This doesn't have a large effect - for frames that reach
the driver, it will do a replay check, and when installing
a new key, the counter is normally zero to start with (not
for GTK though, if joining the BSS for the first time).
Since this only affects frames handled entirely by the FW,
and that's restricted to a few unicast management frames,
the only affect here is for those after a firmware restart.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.1cedf2ca7bb6.I2e609c28eaa301436e6740f4f1beca838f69a96a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
EAPOL failure results in deauthentication with various reasons, not
related to AUTH failure specifically, so we just merge AUTH failure
with failed to assoc to AP.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.2ff350d85eab.I02c5b5d29c0d5c2e014bd1081b07ed33772ae04d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for discovery of hidden networks on the 6GHz band,
by including the scan request direct SSIDs in the FW scan request
command:
- In case a short SSID matches one of the direct SSIDs in the scan
request command, add the matching SSID in the same offset in the
'direct_ssids' array.
- Otherwise, add the SSID in one of the available slots.
Additionally, as a preparation to handle hidden APs, refactor
iwl_mvm_umac_scan_cfg_channels_v6_6g() the function.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.ffb540a70212.Ia2bb9bc9435b833820bcc7dc30adcedb5a5a9869@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The scan request processing populated the direct SSIDs
in the FW scan request command also for 6GHz scan, which is not
needed and might result in unexpected behavior.
Fix the code to add the direct SSIDs only in case the scan
is not a 6GHz scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.f465937c7bbf.Ic11a1659ddda850c3ec1b1afbe9e2b9577ac1800@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the firmware crashes while we're already shutting down
the system, there isn't much we can do since the shutdown
process is continuing and we wanted to do that. Don't do
a FW restart, with the implied debug collection, in this
case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802170640.43a7351ae6bd.I164d48ce4379accf76ea0637983fd946d52dc6f5@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* aggregation handling improvements for some drivers
* hidden AP discovery on 6 GHz and other HE 6 GHz
improvements
* minstrel improvements for no-ack frames
* deferred rate control for TXQs to improve reaction
times
* virtual time-based airtime scheduler
* along with various little cleanups/fixups
-----BEGIN PGP SIGNATURE-----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=nFvj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-06-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes berg says:
====================
Lots of changes:
* aggregation handling improvements for some drivers
* hidden AP discovery on 6 GHz and other HE 6 GHz
improvements
* minstrel improvements for no-ack frames
* deferred rate control for TXQs to improve reaction
times
* virtual time-based airtime scheduler
* along with various little cleanups/fixups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We have mgd_prepare_tx(), but sometimes drivers may want/need
to take action when the exchange finishes, whether successfully
or not.
Add a notification to the driver on completion, i.e. call the
new method mgd_complete_tx().
To unify the two scenarios, and to add more information, make
both of them take a struct that has the duration (prepare only),
subtype (both) and success (complete only).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.5d94e78f6230.I6dc979606b6f28701b740d7aab725f7853a5a155@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sending nulldata packets is important for sw AP link probing and detecting
4-address mode links. The checks that dropped these packets were apparently
added to work around an iwlwifi firmware bug with multi-TID aggregation.
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210619101517.90806-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conceptually, this belongs more into the firmware utils
rather than the mvm opmode, so move the collection and
output there.
Note that this slightly changes the format of the Status
line.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210621103449.b82b60d81346.Ide3b688107f6a59c7fc7eb1d8f2002b0a5c1f2d2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't fill in phy_data.d1 in no-data RX, and thus we
pretend some data is actually filled in radiotap when it
isn't or has default (zero) values.
Fill in phy_data.d1 appropriately, and while at it also
move the info_type initialization into the initializer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.3d488885f77c.Ib97a2bc57c1e9fb98927dc6f802568db313abe3b@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's been a while that the firmware uses LONG_GROUP by default
and not LEGACY_GROUP.
Until now the firmware wrongly advertise the WOWLAN_GET_STATUS
command's version with LEGACY_GROUP, but it is now being fixed.
In order to support both firmwares, first try to get the version
number of the command with the LONG_GROUP and if the firmware
didn't advertise the command version with LONG_GROUP, try to get
the command version with LEGACY_GROUP.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.cd6f4e421430.Iec07c746c8e65bc267e4750f38e4f74f2010ca45@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
