[Why]
Driver get wrap around dmub trace data due to read pointer being
increased incorrectly when there are multiple interrupt
queues with very short interval
[How]
Check read/write pointer before copying data from ring buffer
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
pflip interrupt would not be enabled promptly if a pipe is disabled
and re-enabled, causing flip_done timeout error during DP
compliance tests
[How]
Enable pflip interrupt upon pipe enablement
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In some boot configurations we need to retrieve the currently
UEFI-set dppclk, but there was a typo in the calculation
[how]
Fix typo to make dpp_clk calculate off dpp_clk divider instead of
disp_clk
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On baco-enabled systems running virtual dal, can get set power
state when hw is not initialized
[How]
Skip DC hw part of setPowerState when hw not available
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Ported logic from dcn21 for reading in pipe fusing to dcn30.
Supported configurations are 1 and 6 pipes. Invalid fusing
will revert to 1 pipe being enabled.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For DGPU Navi, the wm_table.nv_entries are used. These entires are not
populated for DCN301 Vangogh APU, but instead wm_table.entries are.
[How]
Use DCN21 Renoir style wm calculations.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Ported logic from dcn21 for reading in pipe fusing to dcn30.
Supported configurations are 1 and 6 pipes. Invalid fusing
will revert to 1 pipe being enabled.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Using values provided by DF for latency may cause hangs in
multi display configurations. Revert change to previous value.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
pflip interrupt would not be enabled promptly if a pipe is disabled
and re-enabled, causing flip_done timeout error during DP
compliance tests
[How]
Enable pflip interrupt upon pipe enablement
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After fixing nested FPU contexts caused by 41401ac677 we're still seeing
complaints about spurious kernel_fpu_end(). As it turns out this was
already fixed for dcn20 in commit f41ed88cbd ("drm/amdgpu/display:
use GFP_ATOMIC in dcn20_validate_bandwidth_internal") but never moved
forward to dcn21.
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Commit 41401ac677 added FPU wrappers to dcn21_validate_bandwidth(),
which was correct. Unfortunately a nested function alredy contained
DC_FP_START()/DC_FP_END() calls, which results in nested FPU context
enter/exit and complaints by kernel_fpu_begin_mask().
This can be observed e.g. with 5.10.20, which backported 41401ac677
and now emits the following warning on boot:
WARNING: CPU: 6 PID: 858 at arch/x86/kernel/fpu/core.c:129 kernel_fpu_begin_mask+0xa5/0xc0
Call Trace:
dcn21_calculate_wm+0x47/0xa90 [amdgpu]
dcn21_validate_bandwidth_fp+0x15d/0x2b0 [amdgpu]
dcn21_validate_bandwidth+0x29/0x40 [amdgpu]
dc_validate_global_state+0x3c7/0x4c0 [amdgpu]
The warning is emitted due to the additional DC_FP_START/END calls in
patch_bounding_box(), which is inlined into dcn21_calculate_wm(),
its only caller. Removing the calls brings the code in line with
dcn20 and makes the warning disappear.
Fixes: 41401ac677 ("drm/amd/display: Add FPU wrappers to dcn21_validate_bandwidth()")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
It just spams the logs.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
After fixing nested FPU contexts caused by 41401ac677 we're still seeing
complaints about spurious kernel_fpu_end(). As it turns out this was
already fixed for dcn20 in commit f41ed88cbd ("drm/amdgpu/display:
use GFP_ATOMIC in dcn20_validate_bandwidth_internal") but never moved
forward to dcn21.
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 41401ac677 added FPU wrappers to dcn21_validate_bandwidth(),
which was correct. Unfortunately a nested function alredy contained
DC_FP_START()/DC_FP_END() calls, which results in nested FPU context
enter/exit and complaints by kernel_fpu_begin_mask().
This can be observed e.g. with 5.10.20, which backported 41401ac677
and now emits the following warning on boot:
WARNING: CPU: 6 PID: 858 at arch/x86/kernel/fpu/core.c:129 kernel_fpu_begin_mask+0xa5/0xc0
Call Trace:
dcn21_calculate_wm+0x47/0xa90 [amdgpu]
dcn21_validate_bandwidth_fp+0x15d/0x2b0 [amdgpu]
dcn21_validate_bandwidth+0x29/0x40 [amdgpu]
dc_validate_global_state+0x3c7/0x4c0 [amdgpu]
The warning is emitted due to the additional DC_FP_START/END calls in
patch_bounding_box(), which is inlined into dcn21_calculate_wm(),
its only caller. Removing the calls brings the code in line with
dcn20 and makes the warning disappear.
Fixes: 41401ac677 ("drm/amd/display: Add FPU wrappers to dcn21_validate_bandwidth()")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable status is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We set up the parameters, but never called the atom table.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:59:
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10014:58: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:177:2: note: in expansion of macro ‘DCE_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10014:58: note: (near initialization for ‘aux_shift.AUX_SW_AUTOINCREMENT_DISABLE’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:177:2: note: in expansion of macro ‘DCE_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10013:56: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:181:2: note: in expansion of macro ‘DCE_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10013:56: note: (near initialization for ‘aux_mask.AUX_SW_AUTOINCREMENT_DISABLE’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hdcp_i2c_offsets[] array did not have an entry for
HDCP_MESSAGE_ID_WRITE_CONTENT_STREAM_TYPE so it led to an off by one
read overflow. I added an entry and copied the 0x0 value for the offset
from similar code in drivers/gpu/drm/amd/display/modules/hdcp/hdcp_ddc.c.
I also declared several of these arrays as having HDCP_MESSAGE_ID_MAX
entries. This doesn't change the code, but it's just a belt and
suspenders approach to try future proof the code.
Fixes: 4c283fdac0 ("drm/amd/display: Add HDCP module")
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/display/dc/dcn30/dcn30_dpp_cm.c:298:33-38:
WARNING: conversion to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Synchronization displays with different timings feature uses
reminder of 64 bit division (modulus operator) , which is not
supported by 32 bit platforms
[how]
Use div64 API for 64 bit modulus
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Tested-by: Bindu Ramamurthy<bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Synchronization displays with different timings feature uses division
operator for 64 bit division, which is not supported by 32 bit platforms
[how]
Use div64 API for 64 bit division
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Tested-by: Bindu Ramamurthy<bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why?]
HSplit should not affect DSC slice count. Can cause improper timings to
be applied for certain modes.
[How?]
No longer change DSC Slice count based on HSplit.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. Driver use umachannelnumber to calculate watermarks for stutter.
In asymmetric memory config, the actual bandwidth is less than
dual-channel. The bandwidth should be the same as single-channel.
2. We found single rank dimm need additional delay time for stutter.
[How]
Get information from each DIMM. Treat memory config as a single-channel
for asymmetric memory in bandwidth calculating. Add additional delay
time for single rank dimm.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
DMUB FW send trace event via outbox0 interrupt. Driver will handle it.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
GPINT timeout is causing PSR_STATE_0 to be returned when it shouldn't.
We must guarantee that PSR is fully disabled before doing hw programming
on driver-side.
[How]
Return invalid state if GPINT command times out. Let existing retry
logic send the GPINT until successful.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Some existing DC interfaces are optimized to return a single eDP
link/stream. Refactored those DC interfaces to support multiple eDP.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently the creation of link encoder objects is tightly coupled to the
creation of link objects. Decoupling link encoder object creation is a
preliminary step in the process of allowing link encoders to be
dynamically assigned to links.
[How]
Add "minimal" link encoder objects which are not associated with any
link until required.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To process AUX transactions with DMUB using inbox1 and outbox1 mail boxes.
[HOW]
1) Added inbox1 command DMUB_CMD__DP_AUX_ACCESS to issue AUX commands
to DMUB in dc_process_dmub_aux_transfer_async(). DMUB processes AUX cmd
with DCN and sends reply back in an outbox1 message triggering an
outbox1 interrupt to driver.
2) In existing driver implementation, AUX commands are processed
synchronously by configuring DCN reg. But in DMUB AUX, driver sends an
inbox1 message and waits for a conditional variable (CV) which will be
signaled by outbox1 ISR.
3) As the driver holds dal and dc locks while waiting for CV, the outbox1
ISR is registered with noMutexWait set to true, which allows ISR to run
and signal CV. This sets a constraint on ISR to not modify variables
such as dc, dmub, etc.
4) Created dmub_outbox.c with dmub_enable_outbox_notification() to enable
outbox1 mailbox.
5) New mailbox address ranges allocated for outbox1 of size DMUB_RB_SIZE.
Created dmub functions for Outbox1: dmub_dcn20_setup_out_mailbox(),
dmub_dcn20_get_outbox1_wptr() and dmub_dcn20_set_outbox1_rptr().
6) Added functions dc_stat_get_dmub_notification() and
dmub_srv_stat_get_notification() to retrieve Outbox1 message.
7) Currently, DMUB doesn't opens DDC in AUX mode before issuing AUX
transaction. A workaround is added in dce_aux_transfer_dmub_raw() to
open in DDC in AUX mode for every AUX transaction.
8) Added dc debug option enable_dmub_aux_for_legacy_ddc enable/disable
DMUB AUX. This debug option is checked dce_aux_transfer_with_retries()
to select the method to process AUX transactions.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/display/dc/dce/dmub_psr.c:273:16-21: WARNING:
conversion to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/display/dc/dcn30/dcn30_dpp_cm.c:243:67-72:
WARNING: conversion to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch enables ASSR if display declares such support in DPCD.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/display/dc/core/dc_link_ddc.c:544:34-39: WARNING:
conversion to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Spatial dithering to 10 bpc depth was disabled for all DCE's.
Testing on DCE-8.3 and DCE-11.2 did not show any obvious ill
effects, but a measureable precision improvement (via colorimeter)
when displaying a fp16 framebuffer to a 10 bpc DP or HDMI connected
HDR-10 monitor.
v2: enable it for all DCEs (Alex)
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com> (v2)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some cases, this function is called when DIG BE is not
connected to DIG FE, in which case a value of zero isn't
invalid and assert should not be hit.
[How]
Remove assert and handle ENGINE_ID_UNKNOWN result in calling
function.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When run igt@kms_vrr in a device that uses DCN2.1 architecture, we
noticed multiple failures. Furthermore, when we tested a VRR demo, we
noticed a system hang where the mouse pointer still works, but the
entire system freezes; in this case, we don't see any dmesg warning or
failure messages kernel. This happens due to a lack of vupdate_no_lock
interrupt, making the userspace wait eternally to get the event back.
For fixing this issue, we need to add the vupdate_no_lock interrupt in
the interrupt list.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
No reason to have uninitialized var at top of function
[How]
Move it to minimum scope where it's actuallty used
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a window of time where we optimize bandwidth due to no streams
enabled will enable PSTATE changing but HUBPs are not disabled yet.
This results in underflow counter increasing in some hotplug scenarios.
[How]
Set the optimize-bandwidth flag for later processing once all the HUBPs
are properly disabled.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Vendor based fan noise improvement
[how]
Report timing synchronizable when DP streams time frame
difference is less than 0.05 percent. Adjust DP DTOs and
sync displays using MASTER_UPDATE_LOCK_DB_X_Y
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some external displays with DP can use seamless boot, but their audio endpoints are
only enabled after hotplug.
On boot, these displays inherit UEFI timings without properly initializing audio.
[How]
Enable display audio when seamless booting with an external monitor over DP.
Signed-off-by: Anthony Wang <anthony1.wang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot over DP MST is not POR, but is not explicitly disabled.
[How]
Add check for DP MST and return false in
dc_validate_seamless_boot_timing.
Signed-off-by: Anthony Wang <anthony1.wang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some cases, this function is called when DIG BE is not
connected to DIG FE, in which case a value of zero isn't
invalid and assert should not be hit.
[How]
Remove assert and handle ENGINE_ID_UNKNOWN result in calling
function.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When run igt@kms_vrr in a device that uses DCN2.1 architecture, we
noticed multiple failures. Furthermore, when we tested a VRR demo, we
noticed a system hang where the mouse pointer still works, but the
entire system freezes; in this case, we don't see any dmesg warning or
failure messages kernel. This happens due to a lack of vupdate_no_lock
interrupt, making the userspace wait eternally to get the event back.
For fixing this issue, we need to add the vupdate_no_lock interrupt in
the interrupt list.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New proposed sequence for HUBP blanking causes regressions where the
hardware would fail to enter blank which triggers an assert in the new
sequence. This change brings back the old sequence.
Fixes: 985faf2c4e ("drm/amd/display: New sequence for HUBP blank")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC version 3.2.123 brings improvements in multiple areas.
In summary, we highlight:
- Firmware release 0.0.52
- Bug fixes on MPC OGAM sequence, display experience, etc.
- Improvements on timing, transmitter control, etc.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
