MODULE_SUPPORTED_DEVICE was added in pre-git era and never was
implemented. We can safely remove it, because the kernel has grown
to have many more reliable mechanisms to determine if device is
supported or not.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The functions that add an async subdev to an async subdev notifier take
as an argument the size of the container structure they need to
allocate. This is error prone, as passing an invalid size will not be
caught by the compiler. Wrap those functions in macros that take a
container type instead of a size, and cast the returned pointer to the
desired type. The compiler will catch mistakes if the incorrect type is
passed to the macro, as the assignment types won't match.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> (core+ti-cal)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Use the appropriate helper v4l2_async_notifier_add_fwnode_remote_subdev,
which handles the needed setup, instead of open-coding it.
This results in removal of the now unneeded driver-specific state
struct dcmi_graph_entity, keeping track of just the source
subdevice.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support of BT656 embedded synchronization bus.
This mode allows to save hardware synchro lines hsync & vsync by replacing
them with synchro codes embedded in data stream.
This bus type is only compatible with 8 bits width data bus.
Due to reserved values 0x00 & 0xff used for synchro codes, valid data vary
from 0x1 to 0xfe, this is up to sensor to clip accordingly pixel data. As
a consequence of this clipping, JPEG is not supported with this bus type.
DCMI crop feature is also not available with this bus type.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace dmaengine_terminate_all() by dmaengine_terminate_sync()
to ensure that all pending dma operations are really finished.
This is not ensured by dmaengine_terminate_all() and this API
is deprecated, so better to use the _sync() variant.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Philippe CORNU <philippe.cornu@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Calling pm_runtime_get_sync increments the counter even in case of
failure, causing incorrect ref count if pm_runtime_put is not
called in error handling paths. Thus replace the jump target
"err_release_buffers" by "err_pm_putw".
Fixes: 152e0bf602 ("media: stm32-dcmi: add power saving support")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'GRABBER' is a weird name, all other types map to the /dev
device names. Rename to 'VIDEO' to be consistent with the
other types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
A null pointer would be passed to a call of the function “of_node_put”
immediately after a call of the function “of_graph_get_next_endpoint”
failed at one place.
Remove this superfluous function call.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support of several sub-devices within pipeline instead
of a single one.
This allows to support a CSI-2 camera sensor connected
through a CSI-2 to parallel bridge.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add media controller support to dcmi in order
to walk within remote subdevices pipeline.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a trace of the set of supported fourcc/mbus_code which
intersect between DCMI and source sub-device.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename "subdev" entity struct field to "source"
to prepare for several subdev support.
Move asd field on top of entity struct.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
During probe, return the provided errors value instead of -ENODEV.
This allows the driver to be deferred probed if needed.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Do not access sd_formats[] if num_of_sd_formats is zero, ie
subdev sensor didn't expose any formats.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Report overrun error only when it exceeds a given threshold.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Avoid call of dmaengine_terminate_all() between
dmaengine_prep_slave_single() and dmaengine_submit() by locking
the whole DMA submission sequence.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Start streaming was sometimes failing because of pm_runtime_get_sync()
non-0 return value. In fact return value was not an error but a
positive value (1), indicating that PM was already enabled.
Fix this by going to error path only with negative return value.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Initialise the V4L2 fwnode endpoints to zero in all drivers using
v4l2_fwnode_endpoint_parse(). This prepares for setting default endpoint
flags as well as the bus type. Setting bus type to zero will continue to
guess the bus among the guessable set (parallel, Bt.656 and CSI-2 D-PHY).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CSI-2 bus may use either D-PHY or C-PHY. Make this visible in media
bus enum.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Switch all media platform drivers to call v4l2_async_notifier_add_subdev()
to add asd's to a notifier, in place of referencing the notifier->subdevs[]
array. These drivers also must now call v4l2_async_notifier_init() before
adding asd's to their notifiers.
There may still be cases where a platform driver maintains a list of
asd's that is a duplicate of the notifier asd_list, in which case its
possible the platform driver list can be removed, and can reference the
notifier asd_list instead. One example of where a duplicate list has
been removed in this patch is xilinx-vipp.c. If there are such cases
remaining, those drivers should be optimized to remove the duplicate
platform driver asd lists.
None of the changes to the platform drivers in this patch have been
tested. Verify that the async subdevices needed by the platform are
bound at load time, and that the driver unloads and reloads correctly
with no memory leaking of asd objects.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Only enable IT frame on JPEG capture, this saves some CPU
interruptions and processing on all the other cases.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This does not fix any bug - this is just a code simplification. As
np is not used after passing it to v4l2_fwnode_endpoint_parse() its
refcount can be decremented immediately and at one location.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The endpoint allocated by of_graph_get_next_endpoint() needs an of_node_put()
in both error and success path. As ep is not used the refcount decrement
can be right after the last use of ep.
Fixes: commit 37404f91ef ("[media] stm32-dcmi: STM32 DCMI camera interface driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The while(1) is effectively useless as all possible paths within it
return thus there is no way to loop.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Do not wait for interrupt completion when stopping streaming,
stopping sensor and disabling interruptions are enough.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cleanup "active" field usage and enhance list management
to avoid exceptions when releasing buffers on error or
stopping streaming.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Return buffer to V4L2 in error state if DMA error occurs.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Return silently instead of falling into error when running
out of available buffers when restarting capture.
Capture will be restarted when new buffers will be
provided by V4L2 client.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Minor non-functional fixes around comments, variable namings
and trace point enhancement.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Do not stop/restart dma on overrun or errors.
Dma will be restarted on current frame transfer
completion. Frame transfer completion is ensured
even if overrun or error occurs by DCMI continuous
capture mode which restarts data transfer at next
frame sync.
Do no warn on overrun while in irq thread, this slows down
system and lead to more overrun errors. Use a counter
instead and log errors at stop streaming.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add g/s_parm framerate support by calling subdev
g/s_frame_interval ops.
This allows user to control sensor framerate by
calling ioctl G/S_PARM.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix some missing "\n".
Trace error returned by subdev streamon/streamoff.
Remove extra "0x" unneeded with %pad formatter.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It is already cleared in dcmi_irq_callback().
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add SPDX identifiers to files under stm32 directory
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The V4L2_ASYNC_MATCH_FWNODE match criteria requires just one
struct to be filled (struct fwnode_handle). The V4L2_ASYNC_MATCH_DEVNAME
match criteria requires just a device name.
So, it doesn't make sense to enclose those into structs,
as the criteria can go directly into the union.
That makes easier to document it, as we don't need to document
weird senseless structs.
At drivers, this makes even clearer about the match criteria.
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Hyun Kwon <hyun.kwon@xilinx.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
