When using a fixed-link configuration in SGMII mode, it's not really
sensible to have auto-negotiation enabled since the link settings are
fixed by definition. In other configurations, such as an SGMII
connection to a PHY, it should generally be enabled.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0a4e9ce17b.
The code was developed and tested on an MSC313E SoC, which seems to be
half-way between the AT91RM9200 and the AT91SAM9260 in that it supports
both the 2-descriptors mode and a Tx ring.
It turns out that after the code was merged I could notice that the
controller would sometimes lock up, and only when dealing with sustained
bidirectional transfers, in which case it would report a Tx overrun
condition right after having reported being ready, and will stop sending
even after the status is cleared (a down/up cycle fixes it though).
After adding lots of traces I couldn't spot a sequence pattern allowing
to predict that this situation would happen. The chip comes with no
documentation and other bits are often reported with no conclusive
pattern either.
It is possible that my change is wrong just like it is possible that
the controller on the chip is bogus or at least unpredictable based on
existing docs from other chips. I do not have an RM9200 at hand to test
at the moment and a few tests run on a more recent 9G20 indicate that
this code path cannot be used there to test the code on a 3rd platform.
Since the MSC313E works fine in the single-descriptor mode, and that
people using the old RM9200 very likely favor stability over performance,
better revert this patch until we can test it on the original platform
this part of the driver was written for. Note that the reverted patch
was actually tested on MSC313E.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/netdev/20201206092041.GA10646@1wt.eu/
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
SAMA7G5's ethernet IPs TX clock could be provided by its generic clock or
by the external clock provided by the PHY. The internal IP logic divides
properly this clock depending on the link speed. The patch adds a new
capability so that macb_set_tx_clock() to not be called for IPs having
this capability (the clock rate, in case of generic clock, is set at the
boot time via device tree and the driver only enables it).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is necessary for SAMA7G5 as it uses different values for
PHY interface and also introduces hdfctlen bit.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for 10GBASE-R interface to the linux driver for
Cadence's ethernet controller.
This controller has separate MAC's and PCS'es for low and high speed paths.
High speed PCS supports 100M, 1G, 2.5G, 5G and 10G through rate adaptation
implementation. However, since it doesn't support auto negotiation, linux
driver is modified to support 10GBASE-R instead of USXGMII.
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Link: https://lore.kernel.org/r/1603975627-18338-1-git-send-email-pthombar@cadence.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The at91rm9200 variant used by a few chips including the MSC313 supports
two Tx descriptors (one frame being serialized and another one queued).
However the driver only implemented a single one, which adds a dead time
after each transfer to receive and process the interrupt and wake the
queue up, preventing from reaching line rate.
This patch implements a very basic 2-deep queue to address this limitation.
The tests run on a Breadbee board equipped with an MSC313E show that at
1 GHz, HTTP traffic on medium-sized objects (45kB) was limited to exactly
50 Mbps before this patch, and jumped to 76 Mbps with this patch. And tests
on a single TCP stream with an MTU of 576 jump from 10kpps to 15kpps. With
1500 byte packets it's now possible to reach line rate versus 75 Mbps
before.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20201011090944.10607-4-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RM9200 supports one frame being sent while another one is waiting in
queue. This avoids the dead time that follows the emission of a frame
and which prevents one from reaching line speed.
Right now the driver supports only a single skb, so we'll first replace
the rm9200-specific skb info with an array of two macb_tx_skb (already
used by other drivers). This patch only moves the skb_length to
txq[0].size and skb_physaddr to skb[0].mapping but doesn't perform any
other change. It already uses [desc] in order to minimize future changes.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20201011090944.10607-3-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Transmit Buffer Register Empty replaces TXERR on RM9200 and signals the
sender may try to send again becase the last queued frame is no longer
in queue (being transmitted or already transmitted).
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20201011090944.10607-2-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
struct macb_platform_data is only used by macb_pci to register the platform
device, move its definition to cadence/macb.h and remove platform_data/macb.h
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt the Wake-on-Lan feature to the Cadence GEM Ethernet controller.
This controller has different register layout and cannot be handled by
previous code.
We disable completely interrupts on all the queues but the queue 0.
Handling of WoL interrupt is done in another interrupt handler
positioned depending on the controller version used, just between
suspend() and resume() calls.
It allows to lower pressure on the generic interrupt hot path by
removing the need to handle 2 tests for each IRQ: the first figuring out
the controller revision, the second for actually knowing if the WoL bit
is set.
Queue management in suspend()/resume() functions inspired from RFC patch
by Harini Katakam <harinik@xilinx.com>, thanks!
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the macb ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
at91ether_init was handling the phy mode and speed but since the switch to
phylink, the NCFGR register got overwritten by macb_mac_config(). The issue
is that the RM9200_RMII bit and the MACB_CLK_DIV32 field are cleared
but never restored as they conflict with the PAE, GBE and PCSSEL bits.
Add new capability to differentiate between EMAC and the other versions of
the IP and use it to set and avoid clearing the relevant bits.
Also, this fixes a NULL pointer dereference in macb_mac_link_up as the EMAC
doesn't use any rings/bufffers/queues.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modify MDIO read/write functions to support
communication with C45 PHY.
Signed-off-by: Milind Parab <mparab@cadence.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the MACB Ethernet driver to the Phylink framework.
The MAC configuration is moved to the Phylink ops and Phylink helpers
are now used in the ethtools functions. This helps to access the flow
control and pauseparam logic and this will be helpful in the future for
boards using this controller with SFP cages.
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The subns increment register has 24 bits as follows:
RegBit[15:0] = Subns[23:8]; RegBit[31:24] = Subns[7:0]
Fix the same in the driver and increase sub ns resolution to the
best capable, 24 bits. This should be the case on all GEM versions
that this PTP driver supports.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scaled ppm parameter passed to _adjfine() contains a 16 bit
fraction. This just happens to be the same as SUBNSINCR_SIZE now.
Hence define this separately.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the macb driver to use NAPI GRO helpers when
receiving SKBs. This improves performances.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SAMA5D2 SoC has a suspend mode where SoC's power is cut off. Due to this
the registers content is lost after a suspend/resume cycle. The current
suspend/resume implementation covers some of these registers. However
there are few which were not treated (e.g. SCRT2 and USRIO). Apart
from this, netdev features are not restored. Treat these issues.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSU clock needs to be enabled/disabled as per support in devicetree
and it should also be controlled during suspend/resume (WOL has no
dependency on this clock).
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the while loop in MDIO read/write functions with a timeout.
In addition, add a check for MDIO bus busy before initiating a new
operation as well to make sure there is no ongoing MDIO operation.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt handler contains a workaround for RX hang applicable
to Zynq and AT91RM9200 only. Subsequent versions do not need this
workaround. This workaround unnecessarily resets RX whenever RX used
bit read is observed, which can be often under heavy traffic. There
is no other action performed on RX UBR interrupt. Hence introduce a
CAPS mask; enable this interrupt and workaround only on affected
versions.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GEM version in ZynqMP and most versions greater than r1p07 supports
TX and RX BD prefetch. The number of BDs that can be prefetched is a
HW configurable parameter. For ZynqMP, this parameter is 4.
When GEM DMA is accessing the last BD in the ring, even before the
BD is processed and the WRAP bit is noticed, it will have prefetched
BDs outside the BD ring. These will not be processed but it is
necessary to have accessible memory after the last BD. Especially
in cases where SMMU is used, memory locations immediately after the
last BD may not have translation tables triggering HRESP errors. Hence
always allocate extra BDs to accommodate for prefetch.
The value of tx/rx bd prefetch for any given SoC version is:
2 ^ (corresponding field in design config 10 register).
(value of this field >= 1)
Added a capability flag so that older IP versions that do not have
DCFG10 or this prefetch capability are not affected.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle HRESP error by doing a SW reset of RX and TX and
re-initializing the descriptors, RX and TX queue pointers.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the phylib now being aware of the "reset-gpios" PHY node property,
there should be no need to frob the PHY reset in this driver anymore...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows filtering received packets to different
hardware queues (aka ntuple).
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able for packet reception on different RX queues some
configuration has to be performed. This patch checks how many
hardware queue does GEM support and initializes them.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on original Harini's patch and Andrei's patch,
implemented in a separate file to ease the review/maintanance
and integration with other platforms.
This driver supports GEM-GXL:
- Register ptp clock framework
- Initialize PTP related registers
- HW time stamp on the PTP Ethernet packets are received using the
SO_TIMESTAMPING API. Time stamps are obtained from the dma buffer
descriptors
- add macb_ptp to compilation chain
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PTP timestamps in
DMA buffer descriptors. It checks capability at runtime
and uses appropriate buffer descriptor.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the MACB is directly connected to a
non-mdio PHY/device, it should be possible to provide
a fixed link configuration in the DT.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in struct
macb, use stats from struct net_device.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/cadence/macb.h:862:33: sparse: expected ; at end of declaration
drivers/net/ethernet/cadence/macb.h:862:33: sparse: Expected } at end of struct-union-enum-specifier
drivers/net/ethernet/cadence/macb.h:862:33: sparse: got phy_interface
drivers/net/ethernet/cadence/macb.h:877:1: sparse: Expected ; at the end of type declaration
drivers/net/ethernet/cadence/macb.h:877:1: sparse: got }
In file included from drivers/net/ethernet/cadence/macb_pci.c:29:0:
drivers/net/ethernet/cadence/macb.h:862:2: error: unknown type name 'phy_interface_t'
phy_interface_t phy_interface;
^~~~~~~~~~~~~~~
Add linux/phy.h to macb.h
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for 32 bit GEM in
64 bit system. It checks capability at runtime
and uses appropriate buffer descriptor.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does the following:
- MACB/GEM-PTP interface
- registers and bitfields for TSU
- capability flags to enable PTP per platform basis
Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New Cadence GEM hardware support Large Segment Offload (LSO):
TCP segmentation offload (TSO) as well as UDP fragmentation
offload (UFO). Support for those features was added to the driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb driver hardcoded the tx/rx ring sizes. This made it
impossible to change the sizes at run time.
Add tx_ring_size, and rx_ring_size variables to macb object, which
are initilized with default vales during macb_init. Change all
references to RX_RING_SIZE and TX_RING_SIZE to their respective
replacements.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the platforms like zynqmp ultrascale+ has a
separate clock gate for the rx clock. Add an optional
rx_clk so that the clock can be enabled.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for 64 bit addressing and BDs.
-> Enable 64 bit addressing in DMACFG register.
-> Set DMA mask when design config register shows support for 64 bit addr.
-> Add new BD words for higher address when 64 bit DMA support is present.
-> Add and update TBQPH and RBQPH for MSB of BD pointers.
-> Change extraction and updation of buffer addresses to use
64 bit address.
-> In gem_rx extract address in one place insted of two and use a
separate flag for RXUSED.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
USRIO and JUMBO CAPS have the same mask.
Fix the same.
Fixes: ce721a7021 ("net: ethernet: cadence-macb: Add disabled usrio caps")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On AT91 SoCs, the User Register (USRIO) exposes a switch to configure the
"Reduced" or "Traditional" version of the Media Independent Interface
(RMII vs. MII or RGMII vs. GMII).
As on the older EMAC version, on GMAC, this switch is set by default to the
non-reduced type of interface, so use the existing capability and extend it to
GMII as well. We then keep the current logic in the macb_init() function.
The capabilities of sama5d2, sama5d4 and sama5d3 GEM interface are updated in
the macb_config structure to be able to properly enable them with a traditional
interface (GMII or MII).
Reported-by: Romain HENRIET <romain.henriet@l-acoustics.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested on Acqua A5 SoM (http://www.acmesystems.it/acqua).
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, the macb integration does not use the USRIO
register to configure the (R)MII port and clocks.
When the register is not implemented and the MACB error signal
is connected to the bus error, reading or writing to the USRIO
register can trigger some Imprecise External Aborts on ARM platforms.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With device tree it is no more possible to reset the PHY at board
level. Furthermore, doing in the driver allow to power down the PHY when
the network interface is no more used.
This reset can't be done at the PHY driver level. The PHY must be able to
answer the to the mii bus scan to let the kernel creating a PHY device.
The patch introduces a new optional property "phy-reset-gpios" inspired
from the one use for the FEC.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the sgmii phy interface.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If an architecture defines readl/writel using CPP macros, we
get the following kinds of build failure:
> > > drivers/net/ethernet/cadence/macb.c:164:1: error: macro "writel"
> > > passed 3 arguments, but takes just 2
> macb_or_gem_writel(bp, SA1B, bottom);
> ^
Rename the methods so that this doesn't happen.
Signed-off-by: David S. Miller <davem@davemloft.net>
