If selftest and reset are performed at the same time, the phy
loopback setting may be still in enable state after the reset,
and device cannot link up. So fix this issue by disabling phy
loopback before phy_start().
Fixes: 256727da73 ("net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW error and global reset are reported through MSIX interrupts.
The same error may be reported to different functions at the
same time. When global reset begins, the pending reset request
set by this error is unnecessary. So clear the pending reset
request after the reset is complete to avoid the repeated reset.
Fixes: f6162d4412 ("net: hns3: add handling of hw errors reported through MSIX")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, netif_tx_stop_all_queues() is used to ensure that
the xmit is not running, but for the concurrent case it will
not take effect, since netif_tx_stop_all_queues() just sets
a flag without locking to indicate that the xmit queue(s)
should not be run.
So use netif_tx_disable() to replace netif_tx_stop_all_queues(),
it takes the xmit queue lock while marking the queue stopped.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When skb->ip_summed is CHECKSUM_PARTIAL, for non-tunnel udp packet,
which has a dest port as the IANA assigned, the hardware is expected
to do the checksum offload, but the hardware whose version is below
V3 will not do the checksum offload when udp dest port is 4790.
So fixes it by doing the checksum in software for this case.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, the device is not initialized because reset failed.
If another task calls hns3_reset_notify_up_enet() before reset
retry, it will cause an error since uninitialized pointer access.
So add check for HNS3_NIC_STATE_INITED before calling
hns3_nic_net_open() in hns3_reset_notify_up_enet().
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message sent to VF should be initialized, otherwise random
value of some contents may cause improper processing by the target.
So add a initialization to message in hclge_get_link_mode().
Fixes: 9194d18b05 ("net: hns3: fix the problem that the supported port is empty")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the UM, the type and enable status of igu_egu_hw_err
should be configured separately. Currently, the type field is
incorrect when disable this error. So fix it by configuring these
two fields separately.
Fixes: bf1faf9415 ("net: hns3: Add enable and process hw errors from IGU, EGU and NCSI")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SEPARATOR_VALUE macro is used as separator when getting
the register value, but the value of this macro is different
between pf and vf, it is a bit confusing for the user, so
synchronize the value of vf with pf.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify some inappropriate spaces in comments of struct
hlcgevf_tqp_stats.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enter suspend mode the counter of pf reset will be increased
twice, since both hclge_prepare_general() and hclge_prepare_wait()
increase this counter. So remove the duplicate counting in
hclge_prepare_general().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reduce the processing of unnecessary mailbox command when PF supports
actively push its link status to VFs, VFs stop sending request link
status command in periodic service task in this case.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, VF updates its link status every second by send query command
to PF in periodic service task. If link stats of PF is changed, VF may
need at most one second to update its link status.
To reduce delay of link status between PF and VFs, PF actively push its
link status to VFs when its link status is updated. And to let VF know
PF supports this new feature, the link status changed mailbox command
adds one bit to indicate it.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset_prepare and reset_done calls have a null pointer check
on ae_dev however ae_dev is being dereferenced via the call to
ns3_is_phys_func with the ae->pdev argument. Fix this by performing
a null pointer check on ae_dev and hence short-circuiting the
dereference to ae_dev on the call to ns3_is_phys_func.
Addresses-Coverity: ("Dereference before null check")
Fixes: 715c58e94f ("net: hns3: add suspend and resume pm_ops")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To implement the system suspend/resume functions, the NIC driver needs
to support:
1. When the system enters the suspend mode, the driver needs to
implement the suspend callback function of the NIC device. The driver
needs to mute the device, stop all RX/TX activities of the device, and
unmap the interrupt.
2. When the system enters the resume mode, the driver needs to
implement the resume callback function of the NIC device and restore
the device to the state before suspension.
When the system enters the suspend and resume mode, the NIC driver
actually executes the PF function reset process.
When the PFs are suspending/resuming, VFs also enter the suspend/resume
state because the PFs trigger the VFs to reset, therefore no operation
is required when the VF pci_driver is suspending or resuming.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flr_prepare/flr_done functions are not only used in the FLR scenario,
but also used in the suspend/resume.
Change the function names to prepare_for_reset/rebuild_for_reset, change
the flr_prepare/flr_done to reset_prepare/reset_done in hnae3_ae_ops.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the VF down state bit is cleared after VF sending
link status request command. There is problem that when VF gets
link status replied from PF, the down state bit may still set
as 1. In this case, the link status replied from PF will be
ignored and always set VF link status to down.
To fix this problem, clear VF down state bit before VF requests
link status.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limiting the scope of the variable vector_ring_chain to the block where it
is used.
Fixes: 424eb834a9 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code to defer the reset(which caps the frequency of the reset) schedules the
timer and returns. Hence, following 'else-if' looks un-necessary.
Fixes: 9de0b86f64 ("net: hns3: Prevent to request reset frequently")
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the left over check and assignment which is no longer used
anywhere in the function and should have been removed as part of the
below mentioned patch.
Fixes: 012fcb52f6 ("net: hns3: activate reset timer when calling reset_event")
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_put_padto() may fails because of memory failure, sw_err_cnt
is already used to log memory failure in hns3_skb_linearize(),
so use it to log the memory failure for skb_put_padto() too.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device HNAE3_DEVICE_VERSION_V3 supports up to 1280 queues
and qsets for one function, so the bitwidth of tc_offset, meaning
the tqps index, needs to expand from 10 bits to 11 bits.
The device HNAE3_DEVICE_VERSION_V3 supports up to 512 queues on
one TC. The tc_size, meaning the exponent with base 2 of queues
supported on TC, which needs to expand from 3 bits to 4 bits.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The actual size on wire for tso skb should be (gso_segs - 1) *
hdr + skb->len instead of skb->len, which can be seen by user using
'ethtool -S ethX' cmd, and 'Byte Queue Limit' also use the send size
stat to do the queue limiting, so add send_bytes in the desc_cb to
record the actual send size for a skb. And send_bytes is only for tx
desc_cb and page_offset is only for rx desc, so reuse the same space
for both of them.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hns3 driver only handle the xmit skb with one level of
fraglist skb, add handling for multi level by calling hns3_tx_bd_num()
recursively when calculating bd num and calling hns3_fill_skb_to_desc()
recursively when filling tx desc.
When the skb has a fraglist level of 24, the skb is simply dropped and
stats.max_recursion_level is added to record the error. Move the stat
handling from hns3_nic_net_xmit() to hns3_nic_maybe_stop_tx() in order
to handle different error stat and add the 'max_recursion_level' and
'hw_limitation' stat.
Note that the max recursive level as 24 is chose according to below:
commit 48a1df6533 ("skbuff: return -EMSGSIZE in skb_to_sgvec to
prevent overflow").
And that we are not able to find a testcase to verify the recursive
fraglist case, so Fixes tag is not provided.
Reported-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the queue reset process needs to be performed one by
one, which is inefficient. However, the queue reset of the same
function is always performed at the same time. Therefore, according
to the UM, command HCLGE_OPC_CFG_RST_TRIGGER can be used to reset
all queues of the same function at a time, in order to optimize
the queue reset process.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if user hasn't change channel number, the rss_size
is limited to be no more than the vector number, in order to
keep one vector only being mapped to one queue. But the queue
number of each tc can be different, and one vector also can
be mapped by multiple queues. So remove this limitation.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The array size of bd_num_list is a fixed value, it may have potential
overflow risk when array size of hclge_dfx_bd_offset_list is greater
than that fixed value. So modify bd_num_list as a pointer and allocate
memory for it according to array size of hclge_dfx_bd_offset_list.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When new rule state is TO_ADD or ACTIVE, and there is already a
rule with same location in the fd_rule_list, the new rule will
be freed after modifying the old rule. It may cause user-after-free
issue when access rule again in hclge_add_fd_entry_common().
Fixes: fc4243b8de ("net: hns3: refactor flow director configuration")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when adding flow director rule, it missed to set
rule state. Which may cause the rule state in software is
unconsistent with hardware.
Fixes: fc4243b8de ("net: hns3: refactor flow director configuration")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hclge_tm_vport_tc_info_update() is bloated, so split it into
separate functions for readability and maintainability.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hclge_reset_rebuild() is a bit too long. So add a new function
hclge_update_reset_level() to improve readability.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/sucessful/successful/
s/serivce/service/
and remove a redundant new.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parameter cm_buf is never used, so remove it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parameter vf in hclge_set_vf_vlan_common() is unused now,
so remove it.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the HW manual, the query operation is unnecessary
when the TM QCN error event is enabled, so remove it.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some redundant blank lines.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vmdq is not supported yet, the num_vmdq_vport is always 0,
it's a bit confusing when using the num_vport, so remove
these unused codes of vmdq.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For DEVICE_VERSION_V3, the hardware supports to match specified
data in the specified offset of packet payload. Each layer can
have one offset, and can't be masked when configure flow director
rule by ethtool command. The layer is selected based on the
flow-type, ether for L2, ip4/ipv6 for L3, and tcp4/tcp6/udp4/udp6
for L4. For example, tcp4/tcp6/udp4/udp6 rules share the same
user-def offset, but each rule can have its own user-def value.
For the user-def field of ethtool -N/U command is 64 bits long.
The bit 0~15 is used for user-def value, and bit 32~47 for user-def
offset in HNS3 driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For only PF driver can configure flow director rule, it's
better to call hclge_del_all_fd_entries() directly in hclge
layer, rather than call hns3_del_all_fd_entries() in hns3
layer. Then the ae_algo->ops.del_all_fd_entries can be removed.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the flow director rule of aRFS is configured in
the IO path. It's time-consuming. So move out the configuration,
and configure it asynchronously. And keep ethtool and tc flower
rule using synchronous way, otherwise the application maybe
unable to know the rule is installed or pending.
Add a state member for each flow director rule to indicate the
rule state. There are 4 states:
TO_ADD: the rule is waiting to add to hardware
TO_DEL: the rule is waiting to remove from hardware
DELETED: the rule has been removed from hardware. It's a middle
state, used to remove the rule node in the fd_rule_list.
ACTIVE: the rule is already added in hardware
For asynchronous way, when receive a new request to add or delete
flow director rule by aRFS, update the rule list, then request to
schedule the service task to finish the configuration.
For synchronous way, when receive a new request to add or delete
flow director rule by ethtool or tc flower, configure hardware
directly, then update the rule list if success.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware supports to parse and match the traffic class field
of IPv6 packet for flow director, uses the same tuple as ip tos.
So removes the limitation of configure 'tclass' by driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there are too many branches for hclge_fd_convert_tuple().
And it may be more when add new tuples. Refactor it by sorting the
tuples according to their length. So it only needs several KEY_OPT
now, and being flexible to add new tuples.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The process of function hclge_fd_get_tuple() is complex and
prolix. To make it more readable, extract the process of each
flow-type tuple to a single function.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The process of function hclge_add_fd_entry() is complex and
prolix. To make it more readable, extract the process of
fs->ring_cookie to a single function.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the imp-controlled PHYs feature is enabled, driver can not
call phy driver interface to set loopback anymore and needs
to send command to firmware to start phy loopback.
Driver reuses the existing firmware command 0x0315 to start
phy loopback, just add a setting bit in this command. As this
command is not only for serdes loopback anymore, rename this
command to "xxx_COMMON_LOOPBACK", and modify function name,
macro name and logs related to it.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the imp-controlled PHYs feature is enabled, driver will not
register mdio bus. In order to support ioctl ops for phy tool to
read or write phy register in this case, the firmware implement
a new command for driver and driver implement ioctl by using this
new command.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the imp-controlled PHYs feature is enabled, phydev is NULL.
In this case, the autoneg is always off when user uses ethtool -a
command to get pause parameters because hclge_get_pauseparam()
uses phydev to check whether device is TP port. To fit this new
feature, use media type to check whether device is TP port.
And when user set pause parameters, these parameters need to
always set to mac, no matter whether autoneg is off.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
