The mlxsw_sp_qdisc argument is not used in any of the actual callbacks.
Drop it.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset provides some updates to mlx5e and mlx5 SW steering drivers:
1) Tariq and Vladyslav they both provide some trivial update to mlx5e netdev.
The next 12 patches in the patchset are focused toward mlx5 SW steering:
2) 3 trivial cleanup patches
3) Dynamic Flex parser support:
Flex parser is a HW parser that can support protocols that are not
natively supported by the HCA, such as Geneve (TLV options) and GTP-U.
There are 8 such parsers, and each of them can be assigned to parse a
specific set of protocols.
4) Enable matching on Geneve TLV options
5) Use Flex parser for MPLS over UDP/GRE
6) Enable matching on tunnel GTP-U and GTP-U first extension
header using
7) Improved QoS for SW steering internal QPair for a better insertion rate
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmB+R90ACgkQSD+KveBX
+j5UKAf+OODHHlYUxp3k4uSRGPNHuVZsUw4DjoCY6b0E4uMup9bP0YF7/B1I8bpC
xTbVK9SzYTVOt0pxBu3aJ1Qom5hpJt5iT7QG9m5LlhEn/ZD3KqpnenGuDMIlyOa5
EvLIdeOoWxJ+7Za6pULy4hsbUcu8hupsBBN+poC3dN4akQu1NyvFE4mdHVTP/c7n
DB0mZWskoDyXm1dQiZ4+cDWoltrrpFLo5n7N08QbS+AvJ7jsRrT5myBU4IPMEfP6
peRecTpKZEOwBwTzxi41ao5XZYnKTROD3zax30v6DXxw5K41SQKwvCjgvpc2/V1J
jymdJzdYa17mxu5XMC0aaQoFo2VBDg==
=wwzX
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-04-19' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-04-19
This patchset provides some updates to mlx5e and mlx5 SW steering drivers:
1) Tariq and Vladyslav they both provide some trivial update to mlx5e netdev.
The next 12 patches in the patchset are focused toward mlx5 SW steering:
2) 3 trivial cleanup patches
3) Dynamic Flex parser support:
Flex parser is a HW parser that can support protocols that are not
natively supported by the HCA, such as Geneve (TLV options) and GTP-U.
There are 8 such parsers, and each of them can be assigned to parse a
specific set of protocols.
4) Enable matching on Geneve TLV options
5) Use Flex parser for MPLS over UDP/GRE
6) Enable matching on tunnel GTP-U and GTP-U first extension
header using
7) Improved QoS for SW steering internal QPair for a better insertion rate
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch the ag71xx on Atheros AR9331 will able to run generic net
selftests.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch FEC on iMX will able to run generic net selftests
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when GID is deleted, it zero out all the fields of the RoCE
address in the SET_ROCE_ADDRESS command for a specified index.
roce_version = 0 means RoCEv1 in the SET_ROCE_ADDRESS command.
This assumes that device has RoCEv1 always enabled which is not always
correct. For example Subfunction does not support RoCEv1.
Due to this assumption a previously added RoCEv2 GID is always deleted as
RoCEv1 GID. This results in a below syndrome:
mlx5_core.sf mlx5_core.sf.4: mlx5_cmd_check:777:(pid 4256): SET_ROCE_ADDRESS(0x761) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x12822d)
Hence set the right RoCE version during GID deletion provided by the core.
Link: https://lore.kernel.org/r/d3f54129c90ca329caf438dbe31875d8ad08d91a.1618753425.git.leonro@nvidia.com
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
When using SW steering, rule insertion rate depends on the RDMA RC QP
performance used for writing to the ICM. During stress this QP is competing
on the HW resources with all the other QPs that are used to send data.
To protect SW steering QP's performance in such cases, we set this QP to
use isolated VL. The VL number is reserved by FW and is not exposed to the
driver.
Support for this QP on isolated VL exists only when both force-loopback and
isolate_vl_tc capabilities are set.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When supported by the device, SW steering RoCE RC QP that is used to
write/read to/from ICM will be created with force-loopback attribute.
Such QP doesn't require GID index upon creation.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Query the flex_parser id that's intended for TNL_MPLS
and use an appropriate flex parser for MPLS over UDP/GRE.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Set the flex parser ID dynamicly for ICMP instead of relying
on hardcoded values.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Flex parser is a HW parser that can support protocols that are not
natively supported by the HCA, such as Geneve (TLV options) and GTP-U.
There are 8 such parsers, and each of them can be assigned to parse a
specific set of protocols.
This patch adds misc4 match params which allows using a correct flex parser
that was programmed to the required protocol.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Remove MPLS specific fields from flex parser 3 layout.
Flex parser can be used for multiple protocols and should
not be hardcoded to a specific type.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add error code to the error messages and removed duplicated message:
if termination table creation failed, we already get an error message
in mlx5_eswitch_termtbl_create, so no need for the additional error print
in the calling function.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Rename the argument to better reflect that the meaning is
not number of records, but wheather or not we should
ring the dorbell.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Striding RQ attributes below are mutually dependent. An unaware
change to one might take the others out of the valid range derived
by the HW caps:
- The MPWQE size in bytes
- The number of strides in a MPWQE
- The stride size
Add checks to verify they are valid and comply to the HW spec
and SW assumptions/requirements.
This is not a fix, no particular issue exists today.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
If mlx5e_devlink_port_register() fails, driver may try to register
devlink health TX and RX reporters on non-registered devlink port.
Instead, create health reporters only if mlx5e_devlink_port_register()
does not fail. And destroy reporters only if devlink_port is registered.
Also, change mlx5e_get_devlink_port() behavior and return NULL in case
port is not registered to replicate devlink's wrapper when ndo is not
implemented.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The changes done in commit [1] were missed by the code movements
done in [2], as they were developed in ~parallel.
Here we re-apply them.
[1] commit e4484d9df5 ("net/mlx5e: Enable striding RQ for Connect-X IPsec capable devices")
[2] commit b3a131c2a1 ("net/mlx5e: Move params logic into its dedicated file")
Fixes: b3a131c2a1 ("net/mlx5e: Move params logic into its dedicated file")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Michael suggest a few more stats we can expose.
$ ethtool -S eth0 --groups eth-mac
Standard stats for eth0:
eth-mac-FramesTransmittedOK: 902623288966
eth-mac-FramesReceivedOK: 28727667047
eth-mac-FrameCheckSequenceErrors: 1
eth-mac-AlignmentErrors: 0
eth-mac-OutOfRangeLengthField: 0
$ ethtool -S eth0 | grep '\(fcs\|align\|oor\)'
rx_fcs_err_frames: 1
rx_align_err_frames: 0
tx_fcs_err_frames: 0
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI match for AC3X 98DX3265 device which is supported by the current
driver and firmware.
Signed-off-by: Vadym Kochan <vkochan@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move structs/defines for ethernet/dma register into driver, since they
are only used for this driver and remove any MIPS specific includes.
This makes it possible to COMPILE_TEST the driver.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
With device tree clock is provided via CCF. For non device tree
use a maximum clock value to not overclock the PHY. The non device
tree usage will go away after platform is converted to DT.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is no mac address passed via platform data try to get it via
device tree and fall back to a random mac address, if all fail.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of access to struct korina_device by just passing the mac
address via platform data and use drvdata for passing netdev to remove
function.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of messing with MIPS specific macros use DMA API for mapping
descriptors and skbs.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove helpers, which are only used in one call site.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Descriptors are mapped uncached so there is no need to do any cache
handling for them.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify probe/remove code by using devm_ functions.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed MDIO functions to work reliable and not just by accident.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not hit EOPNOTSUPP when flowtable offload provides a VLAN pop action.
Fixes: efce49dfe6 ("netfilter: flowtable: add vlan pop action offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch 2ed37183ab ("netfilter: flowtable: separate replace, destroy and
stats to different workqueues") splits the workqueue per event type. Add
a mutex to serialize updates.
Fixes: 502e84e238 ("net: ethernet: mtk_eth_soc: add flow offloading support")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The former fix only papered over the actual problem: the
ethernet core expects the netdev .dev member to have the
proper DMA masks set, or there will be BUG_ON() triggered
in kernel/dma/mapping.c.
Fix this by simply copying dma_mask and dma_mask_coherent
from the parent device.
Fixes: e45d0fad4a ("net: ethernet: ixp4xx: Use parent dev for DMA pool")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue was traffic problems after a while with increased ping times if
flow offload is active. It turns out that key_offset with cookie is
needed in rhashtable_params but was re-assigned to head_offset.
Fix the assignment.
Fixes: 502e84e238 ("net: ethernet: mtk_eth_soc: add flow offloading support")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SEPARATOR_VALUE macro is used as separator when getting
the register value, but the value of this macro is different
between pf and vf, it is a bit confusing for the user, so
synchronize the value of vf with pf.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify some inappropriate spaces in comments of struct
hlcgevf_tqp_stats.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enter suspend mode the counter of pf reset will be increased
twice, since both hclge_prepare_general() and hclge_prepare_wait()
increase this counter. So remove the duplicate counting in
hclge_prepare_general().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kernel test robot reports build errors in 3 Xilinx ethernet drivers.
They all use ioremap functions that are only available when HAS_IOMEM
is set/enabled. If it is not enabled, they all have build errors,
so make these 3 drivers depend on HAS_IOMEM.
ld: drivers/net/ethernet/xilinx/xilinx_emaclite.o: in function `xemaclite_of_probe':
xilinx_emaclite.c:(.text+0x9fc): undefined reference to `devm_ioremap_resource'
ld: drivers/net/ethernet/xilinx/xilinx_axienet_main.o: in function `axienet_probe':
xilinx_axienet_main.c:(.text+0x942): undefined reference to `devm_ioremap_resource'
ld: drivers/net/ethernet/xilinx/ll_temac_main.o: in function `temac_probe':
ll_temac_main.c:(.text+0x1283): undefined reference to `devm_platform_ioremap_resource_byname'
ld: ll_temac_main.c:(.text+0x13ad): undefined reference to `devm_of_iomap'
ld: ll_temac_main.c:(.text+0x162e): undefined reference to `devm_platform_ioremap_resource'
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Cc: Gary Guo <gary@garyguo.net>
Cc: Zhang Changzhong <zhangchangzhong@huawei.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: stable@vger.kernel.org
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
In the ENETC receive path, a frame received by the MAC is first stored
in a 256KB 'FIFO' memory, then transferred to DRAM when enqueuing it to
the RX ring. The FIFO is a shared resource for all ENETC ports, but
every port keeps track of its own memory utilization, on RX and on TX.
There is a setting for RX rings through which they can either operate in
'lossy' mode (where the lack of a free buffer causes an immediate
discard of the frame) or in 'lossless' mode (where the lack of a free
buffer in the ring makes the frame stay longer in the FIFO).
In turn, when the memory utilization of the FIFO exceeds a certain
margin, the MAC can be configured to emit PAUSE frames.
There is enough FIFO memory to buffer up to 3 MTU-sized frames per RX
port while not jeopardizing the other use cases (jumbo frames), and
also not consume bytes from the port TX allocations. Also, 3 MTU-sized
frames worth of memory is enough to ensure zero loss for 64 byte packets
at 1G line rate.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NXP ENETC is a 4-port Ethernet controller which 'smells' to
operating systems like 4 distinct PCIe PFs with SR-IOV, each PF having
its own driver instance, but in fact there are some hardware resources
which are shared between all ports, like for example the 256 KB SRAM
FIFO between the MACs and the Host Transfer Agent which DMAs frames to
DRAM.
To hide the stuff that cannot be neatly exposed per port, the hardware
designers came up with this idea of having a dedicated register block
which is supposed to be populated by the bootloader, and contains
everything configuration-related: MAC addresses, FIFO partitioning, etc.
When a port is reset using PCIe Function Level Reset, its defaults are
transferred from the IERB configuration. Most of the time, the settings
made through the IERB are read-only in the port's memory space (if they
are even visible), so they cannot be modified at runtime.
Linux doesn't have any advanced FIFO partitioning requirements at all,
but when reading through the hardware manual, it became clear that, even
though there are many good 'recommendations' for default values, many of
them were not actually put in practice on LS1028A. So we end up with a
default configuration that:
(a) does not have enough TX and RX byte credits to support the max MTU
of 9600 (which the Linux driver claims already) properly (at full speed)
(b) allows the FIFO to be overrun with RX traffic, potentially
overwriting internal data structures.
The last part sounds a bit catastrophic, but it isn't. Frames are
supposed to transit the FIFO for a very short time, but they can
actually accumulate there under 2 conditions:
(a) there is very severe congestion on DRAM memory, or
(b) the RX rings visible to the operating system were configured for
lossless operation, and they just ran out of free buffers to copy
the frame to. This is what is used to put backpressure onto the MAC
with flow control.
So since ENETC has not supported flow control thus far, RX FIFO overruns
were never seen with Linux. But with the addition of flow control, we
should configure some registers to prevent this from happening. What we
are trying to protect against are bad actors which continue to send us
traffic despite the fact that we have signaled a PAUSE condition. Of
course we can't be lossless in that case, but it is best to configure
the FIFO to do tail dropping rather than letting it overrun.
So in a nutshell, this driver is a fixup for all the IERB default values
that should have been but aren't.
The IERB configuration needs to be done _before_ the PFs are enabled.
So every PF searches for the presence of the "fsl,ls1028a-enetc-ierb"
node in the device tree, and if it finds it, it "registers" with the
IERB, which means that it requests the IERB to fix up its default
values. This is done through -EPROBE_DEFER. The IERB driver is part of
the fsl_enetc module, but is technically a platform driver, since the
IERB is a good old fashioned MMIO region, as opposed to ENETC ports
which pretend to be PCIe devices.
The driver was already configuring ENETC_PTXMBAR (FIFO allocation for
TX) because due to an omission, TXMBAR is a read/write register in the
PF memory space. But the manual is quite clear that the formula for this
should depend upon the TX byte credits (TXBCR). In turn, the TX byte
credits are only readable/writable through the IERB. So if we want to
ensure that the TXBCR register also has a value that is correct and in
line with TXMBAR, there is simply no way this can be done from the PF
driver, access to the IERB is needed.
I could have modified U-Boot to fix up the IERB values, but that is
quite undesirable, as old U-Boot versions are likely to be floating
around for quite some time from now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though ENETC interfaces are exposed as individual PCIe PFs with
their own driver instances, the ENETC is still fundamentally a
multi-port Ethernet controller, and some parts of the IP take a port
number (as can be seen in the PSFP implementation).
Create a common helper that can be used outside of the TSN code for
retrieving the ENETC port number based on the PF number. This is only
correct for LS1028A, the only Linux-capable instantiation of ENETC thus
far.
Note that ENETC port 3 is PF 6. The TSN code did not care about this
because ENETC port 3 does not support TSN, so the wrong mapping done by
enetc_get_port for PF 6 could have never been hit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a VF driver for Microsoft Azure Network Adapter (MANA) that will be
available in the future.
Co-developed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Co-developed-by: Shachar Raindel <shacharr@microsoft.com>
Signed-off-by: Shachar Raindel <shacharr@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert indirect probe call to its direct equivalent to create a symbol
link between RDMA and netdev modules. This will give us an ability to
remove custom module reference counting that doesn't belong to the driver.
Link: https://lore.kernel.org/r/20210401065715.565226-3-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-By: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Currently, if the user changes the pause settings, the default settings
will be restored after an interface down/up cycle, and also when
resuming from suspend. This doesn't seem to provide the best user
experience. Change this to keep user settings, and just ensure that in
jumbo mode pause is disabled.
Small drawback: When switching back mtu from jumbo to non-jumbo then
pause remains disabled (but user can enable it using ethtool).
I think that's a not too common scenario and acceptable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Described in fd5736bf9f ("enetc: Workaround for MDIO register access
issue") is a workaround for a hardware bug that requires a register
access of the MDIO controller to never happen concurrently with a
register access of a port PF. To avoid that, a mutual exclusion scheme
with rwlocks was implemented - the port PF accessors are the 'read'
side, and the MDIO accessors are the 'write' side.
When we do XDP_REDIRECT between two ENETC interfaces, all is fine
because the MDIO lock is already taken from the NAPI poll loop.
But when the ingress interface is not ENETC, just the egress is, the
MDIO lock is not taken, so we might access the port PF registers
concurrently with MDIO, which will make the link flap due to wrong
values returned from the PHY.
To avoid this, let's just slap an enetc_lock_mdio/enetc_unlock_mdio at
the beginning and ending of enetc_xdp_xmit. The fact that the MDIO lock
is designed as a rwlock is important here, because the read side is
reentrant (that is one of the main reasons why we chose it). Usually,
the way we benefit of its reentrancy is by running the data path
concurrently on both CPUs, but in this case, we benefit from the
reentrancy by taking the lock even when the lock is already taken
(and that's the situation where ENETC is both the ingress and the egress
interface for XDP_REDIRECT, which was fine before and still is fine now).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
