Current FIFO size calculation is wrong for two reasons:
- We access lmac 0 by default
- We don't take 11ax into consideration.
Fix both.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since AMSDUs are not de-aggregated by HW in monitor mode,
we still need the option for setting large RBs (up to 12K).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make the adjustments for gen2 TX and RX of TKIP packets. Strip MIC on
RX. Don't add IV space and keep the MIC space zeroed on TX.
Devices that support gen2 data path support TKIP only in station mode.
In all other modes, fall back to SW encryption. Do this early in the
set_key() callback so that the key flags would not be incorrectly set.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to receive TB (Trigger Based) PPDU in monitor mode,
the Driver must send the HE_AIR_SNIFFER_CONFIG_CMD host command.
Enable that via debugfs.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
CDB support has nothing to do with non unified image.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Alexei's patch, assumed that all versions of "struct iwl_error_event_table"
are the same, but there are really different versions in different files.
Rather than trying to fix this, or splitting the tracepoint, or anything of
the sort, just remove it entirely - turns out that nobody really uses it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We already report the RU offset, so we'd better also
report that we know the value.
Fixes: e5721e3f77 ("iwlwifi: mvm: add radiotap data for HE")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Check the actual bit (mask) in Rx notification rate_n_flags.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In new devices, access to periphery is forbidden. Send instead
host command to start and stop debugging.
Memory allocation is written in context info, but in case we
need to update it there is a dedicated command. Add definitions,
currently unused, of the new command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the restart FW debug code to a function. This avoids code
duplication and lays the infra to support the new start and stop
host commands in some future devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Align to new 11ax draft D3.0. Change/add new MAC and PHY capabilities
and update drivers' 11ax capabilities and mac80211's debugfs
accordingly.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of fragmented scan on the HB channels, configure EBS to be
fragmented as well.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support more txq_alloc command types by moving the command declaration
to the gen specific area. While at it, move some of the code segments
to a common place for re-use.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Decode the HE TB PPDU data that we get in sniffer mode
and use it to populate the HE radiotap information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add flags to the tlc_cfg_cmd for signaling peer support for receiving
Dual Carrier Modulation at BPSK (MCS 0), and set them according to peer
capabilities.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the HE phy capabilities IE there are 2 bits to signal support for
STBC in bandwidths of 80Mhz or less, and of 160Mhz.
Use these bits to determine STBC support if this IE exists.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make all FW debug data stop recording flows to use
iwl_fw_dbg_stop_recording function instead of writing to FW
registers directly.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As with the non-offloaded rs case, during assoc on the ap side the phy
context is set to 20MHz until authorization of a client that supports
wider channel-widths. Support this by sending the initial
tlc_config_cmd with max supported channel width of 20MHz until
authorization succeeds.
Fixes: 6b7a5aea71 ("iwlwifi: mvm: always init rs with 20mhz bandwidth rates")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Probe responses were sent to the multicast station while
they should be routed to the broadcast station.
This has no negative effect since the frame was still
routed to the right queue, but it looked very fishy
to send a frame to a (queue, station) tuple where
'queue' is not mapped to 'station'.
Fixes: 7c305de2b9 ("iwlwifi: mvm: Direct multicast frames to the correct station")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the bandwidth is only 20 MHz, then the second channel doesn't
exist, but the hardware reports the CRC was OK. Suppress the data
of the second channel in the HE radiotap in this case, by marking
it as not known.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is the same as for SU PPDUs, so it's easy to do.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The GI duration depends on the frame type in some cases,
take that into account when decoding for radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
I evidently completely confused "number of LTF symbols" and "LTF size".
Radiotap was reporting the former, while I thought it was the latter,
and we really need both.
Add the LTF symbol size into the newly defined field in radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement the extended HE-MU info type decoding to show the HE-SIG-B
common contents in the HE-MU radiotap field.
The DW4 data is partially overwritten by the hardware in all cases, so
only the higher 16 bits can be used. To be able to use it for the HE
SIG-B common data anyway, move the bits around in the following way:
SIG-B common 0: DW 4 -> DW 7
SIG-B common 1: DW 7 -> DW 8
SIG-B common 2: DW 8 -> DW 4 (upper half)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The Free Software Foundation address is superfluous and causes
checkpatch to issue a warning when present. Remove all paragraphs
with FSF's address to prevent that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The parameter that indicated whether the LQ command should be sent
as sync or async was removed, causing the LQ command to be sent as
sync from interrupt context (e.g. from the RX path). This resulted
in a kernel warning: "scheduling while atomic" and failing to send
the LQ command, which ultimately leads to a queue hang.
Fix it by adding back the required parameter to send the command as
sync only when it is allowed.
Fixes: d94c5a820d ("iwlwifi: mvm: open BA session only when sta is authorized")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we receive TX response, we may release a few packets
due to a hole that was closed in the transmission window.
However, if that frame failed, we will mark all the released
frames as failed and will send multiple BARs.
This affects statistics badly, and cause unnecessary frames
transmission.
Instead, mark all the following packets as success, with the
desired result of sending a bar for the failed frame only.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is a bug in FW where the sequence control may be
incorrect, and the driver overrides it with the value
of the ieee80211 header.
However, in BAR there is no sequence control in the header,
which result with arbitrary sequence.
This access to an unknown location is bad and it makes the
logs very confusing - so fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the NIC is disconnected, we just can't do anything
besides seeking for help from the bus driver. Dumping the
device's memory is not necessary and just bloats the logs
with unusable data. Moreover, asking mac80211 to restart
the hardware is also useless. Bypass all this.
Also, use the STATUS_TRANS_DEAD status bit instead of a
bool inside the transport layer. The advantage of this is
that now, the transport and the op_mode can know what is the
situation and bypass the useless recovery steps mentioned
above.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new coex schema requires moving to SISO only when BT AG is 4.
Adjust the SISO criteria according to the coex schema version reported
by firmware.
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update reduce tx power command API to be compatible with new FW API.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While associated in low latency mode, or when traffic load is high,
don't enable EBS in scan request if fragmented EBS is not supported
by the FW.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The HE code is bloating the RX handling, and makes it too big.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The HE code is bloating the RX handling, and makes it too big.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Current implementation turns this bit on only for HE MU.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A probe response built by a P2P GO should contain:
1. CSA/eCSA IE when relevant
2. If the corresponding probe request had P2P IE, then
need to add P2P IE with NOA attributes.
However, the NOA attributes and the updated channel switch
counter are known only to the FW. The solution is that FW
will send a notification with the relevant probe response
data and the driver will save it and update the probe
response accordingly.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A new FW API has been added for WOWLAN_GET_STATUSES to support
multiple GTK keys and IGTK keys. Check the respective TLV and use the
new API when it is set.
Let most of the code use the new version (v7) and convert the old
version (v6) to the new one when needed.
Also refactor some functions a bit so that they can be reused more
easily. Particularly the part that calls WOWLAN_GET_STATUSES which is
reused in D3 and D0i3.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Runtime PM can only be used if CONFIG_PM is set. Move all the d0i3
code (which is essentially runtime PM) behind the CONFIG_PM flag.
This prevents undefined usage of some functions when CONFIG_PM is not
defined.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We repeated the same if twice in a row. Remove the second one and
move the code block into the previous one.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During d3, the firmware records debug data into internal buffer
if debug data collection occurs, collect the data that was written to the
buffer
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The tid for Non-QOS frames is set to IWL_MAX_TID_COUNT. This value
is also used for configuring the queue for non-QOS data. However, this
tid is used by the FW for management queues. As a result, the FW
does not encrypt non-QOS data frames.
Fix this by setting the tid for non-QOS data frames to zero, which
is a valid value for data frames in the FW.
This also fixes a bug in sending multicast frames, where the queues
are allocated with tid == 0, but are sent with tid == 8, which may
lead to unexpected behavior.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Balanced power save mode isn't supported in the fw for 22560 devices
yet. Configure the power save mode to CAM until it gets implemented.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This reverts commit f2e66c8df0.
The firmware never implemented this, and they do not plan to.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently multi-queue is disabled for 22000 devices.
This was since driver isn't supposed to write to prph
registers anymore, and FW needs to configure the RFH.
Now that FW added support for the API - use it and remove
the 22000 multi RX queue disablement.
Bump min API version to avoid compatibility issues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the firmware does not stop recording debugging data when
entering D3 and this causes trouble (e.g. sporadic wake ups).
Fix that by stopping dbg recording when suspending.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Reading and dumping memory areas takes time, and sometimes
dumping all of the areas isn't necessary.
Allow choosing the memory areas which should be dumped.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22560 devices use a new rx_mpdu_desc api.
Update the code to use the new api.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The smallest rb size supported today is 4k rx buffers.
22560 devices use 2k rxb's, so allow using 2k buffers.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22560 devices use a new tx cmd api. Update the code to use
the new api.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
