In case the device is stopped any usage of hw queues needs to be
reallocated in fw due to fw reset after device stop, so all driver
internal queue should also be freed, and if we don't free the next usage
would leak the old memory and get in recover flows
"iwlwifi 0000:00:03.0: dma_pool_destroy iwlwifi:bc" warning.
Also warn about trying to reuse an internal allocated queue.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.c72d2f0355c4.Ia3baff633b9b9109f88ab379ef0303aa152c16bf@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Debug message "firmware didn't ACK the reset - continue anyway\n"
in fw_reset_handshake() is classified as error, however this is not
an error as it is ignored. So, change it to info message for proper
classification of debug messages.
Signed-off-by: Ravi Darsi <ravi.darsi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.449b3092c330.I515edcc41913ca7fbe4a4de923671d120d5618c6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As the context info gen3 code is only called for >=AX210 devices
(from iwl_trans_pcie_gen2_start_fw()) the code there to set LTR
on 22000 devices cannot actually do anything (22000 < AX210).
Fix this by moving the LTR code to iwl_trans_pcie_gen2_start_fw()
where it can handle both devices. This then requires that we kick
the firmware only after that rather than doing it from the context
info code.
Note that this again had a dead branch in gen3 code, which I've
removed here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: ed0022da8b ("iwlwifi: pcie: set LTR on more devices")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210326125611.675486178ed1.Ib61463aba6920645059e366dcdca4c4c77f0ff58@changeid
Instead of pretending to have NAPI and then relying entirely on
interrupts anyway, properly implement NAPI and schedule the poll
when we get an interrupt, re-enabling the interrupt only after
the poll completed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.a5951ac4fc06.I9c84a147288fcfb1b019572c6758f2d92949f5d7@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are some races in the hardware that can possibly lead to
a bus lockup later during a restart when we manage to kill the
firmware at a bad time (while it's accessing the bus).
To work around this, add support for a new handshake between
firmware and driver to ensure that the firmware is in a well-
known state before we kill it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.7756fcc9865c.I13de65e0ffcb4186dd4c1a465f66df2e98c9a947@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't want to have txq code in the PCIe transport code, so move all
the relevant elements to a new iwl_txq structure and store it in
iwl_trans.
spatch
@ replace_pcie @
struct iwl_trans_pcie *trans_pcie;
@@
(
-trans_pcie->queue_stopped
+trans->txqs.queue_stopped
|
-trans_pcie->queue_used
+trans->txqs.queue_used
|
-trans_pcie->txq
+trans->txqs.txq
|
-trans_pcie->txq
+trans->txqs.txq
|
-trans_pcie->cmd_queue
+trans->txqs.cmd.q_id
|
-trans_pcie->cmd_fifo
+trans->txqs.cmd.fifo
|
-trans_pcie->cmd_q_wdg_timeout
+trans->txqs.cmd.wdg_timeout
)
// clean all new unused variables
@ depends on replace_pcie @
type T;
identifier i;
expression E;
@@
- T i = E;
... when != i
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.a428d3c9d66f.Ie04ae55f33954636a39c98e7ae1e739c0507435b@changeid
* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;
-----BEGIN PGP SIGNATURE-----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=Ovcw
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2020-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First set of patches intended for v5.6
* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;
We needed this abstraction for some CSR registers for
IWL_DEVICE_22560, but that has been removed, so we don't need the
abstraction anymore. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to reset the NIC after setting the bits to enable power
gating and that cannot be done too late in the flow otherwise it
cleans other registers and things that were already configured,
causing initialization to fail.
In order to fix this, move the function to the common code in trans.c
so it can be called directly from there at an earlier point, just
after the reset we already do during initialization.
Fixes: 9a47cb9883 ("iwlwifi: pcie: add workaround for power gating in integrated 22000")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205719
Cc: stable@ver.kernel.org # 5.4+
Reported-by: Anders Kaseorg <andersk@mit.edu>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is dead code, nothing uses the IWL_DEVICE_22560 macro and
thus nothing every uses IWL_DEVICE_FAMILY_22560. Remove it all.
While at it, remove some code and definitions used only in this
case, and clean up some comments/names that still refer to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a workaround that forces power gating to be enabled on integrated
22000 devices. This improves power saving in certain situations.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Stop accessing the trans configuration via the iwl_cfg structure and
always access it via the iwl_trans structure. This completes the
requirements to disassociate the trans-specific configuration from the
rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a pointer to the iwl_trans structure and point it to the trans
part of the cfg. This is the first step in disassociating the trans
configuration from the rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This means:
1) stop calling pm_runtime_resume when starting the hardware
2) removing the unneeded low_power parameter to start / stop hw / fw
transport ops
3) squashing transport functions that are now the same
_iwl_trans_pcie_start_hw / iwl_trans_pcie_start_hw
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The op mode should stop the debug recording and not the transport layer.
Rename iwl_fwrt_stop_device into iwl_fw_dbg_stop_sync and move the debug
stop recording to it.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newest devices have a new firmware load mechanism. This
mechanism is called the context info. It means that the
driver doesn't need to load the sections of the firmware.
The driver rather prepares a place in DRAM, with pointers
to the relevant sections of the firmware, and the firmware
loads itself.
At the end of the process, the firmware sends the ALIVE
interrupt. This is different from the previous scheme in
which the driver expected the FH_TX interrupt after each
section being transferred over the DMA.
In order to support this new flow, we enabled all the
interrupts. This broke the assumption that we have in the
code that the RF-Kill interrupt can't interrupt the firmware
load flow.
Change the context info flow to enable only the ALIVE
interrupt, and re-enable all the other interrupts only
after the firmware is alive. Then, we won't see the RF-Kill
interrupt until then. Getting the RF-Kill interrupt while
loading the firmware made us kill the firmware while it is
loading and we ended up dumping garbage instead of the firmware
state.
Re-enable the ALIVE | RX interrupts from the ISR when we
get the ALIVE interrupt to be able to get the RX interrupt
that comes immediately afterwards for the ALIVE
notification. This is needed for non MSI-X only.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The 0xF6 command used to start and stop the recording from 22560 devices
was removed. This is causing an assert when the driver tries to alter
the recording state.
Remove the use of the command.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TFD_*_SLOTS and IWL_*_QUEUE_SIZE both define the TX queue
size (number of TFDs).
Get rid of TFD_*_SLOTS and use only IWL_*_QUEUE_SIZE.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new device family AX210.
Make the needed changes for this family.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The typical sequence of setting INIT_DONE and then waiting
for clock stabilisation is going to need a new workarounds,
so first of all refactor it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In new devices, access to periphery is forbidden. Send instead
host command to start and stop debugging.
Memory allocation is written in context info, but in case we
need to update it there is a dedicated command. Add definitions,
currently unused, of the new command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the restart FW debug code to a function. This avoids code
duplication and lays the infra to support the new start and stop
host commands in some future devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make all FW debug data stop recording flows to use
iwl_fw_dbg_stop_recording function instead of writing to FW
registers directly.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This will allow using the same init in future generations.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We would like to allow using tx init code for other queues but
the command queue - for newer devices.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Context information structure was added to 22000 devices for
firmware self init.
In the next generation of devices the context information
changes significantly, and the original context information
is divided roughly to three data structures: context information gen3,
prph information and prph scratch.
In addition, the init flow changes so the firmware is loaded
by the IML, and so we must allocate the IML on the DRAM and
give the ROM the IML's address before kicking the firmware's
self init.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Different device families may have different flag values
for passing a message to the fw (i.e. SW_RESET).
In order to keep the code readable, and avoid conditioning
upon the family, store a value for each flag, which indicates
the bit that needs to be enabled.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Most of the sw resets in the code are done by one function,
which writes to the relevant CSR.
Use the common function to perform the only reset which was
done separately, redundant to the common code.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When getting HW rfkill we get stop_device being called from
two paths.
One path is the IRQ calling stop device, and updating op
mode and stack.
As a result, cfg80211 is running rfkill sync work that shuts
down all devices (second path).
In the second path, we eventually get to iwl_mvm_stop_device
which calls iwl_fw_dump_conf_clear->iwl_fw_dbg_stop_recording,
that access periphery registers.
The device may be stopped at this point from the first path,
which will result with a failure to access those registers.
Simply checking for the trans status is insufficient, since
the race will still exist, only minimized.
Instead, move the stop from iwl_fw_dump_conf_clear (which is
getting called only from stop path) to the transport stop
device function, where the access is always safe.
This has the added value, of actually stopping dbgc before
stopping device even when the stop is initiated from the
transport.
Fixes: 1efc3843a4 ("iwlwifi: stop dbgc recording before stopping DMA")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Rename this function to the more appropriate iwl_pcie_check_hw_rf_kill()
since it's only a function in the pcie code and cannot be called from
any other place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The newest devices need a longer time to reset because of
their more complex hardware. Wait 5ms after device reset.
Consolidate all the places that reset the device in the
PCIe transport to avoid future bugs.
While at it, unify the flow to use set_bit instead of full
write as requested by the hardware designers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When toggling the RF-kill pin quickly in succession, the driver can
get rather confused because it might be in the process of shutting
down, expecting all commands to go through quickly due to rfkill,
but the transport already thinks the device is accessible again,
even though it previously shut it down. This leads to bugs, and I
even observed a kernel panic.
Avoid this by making the PCIe code only report that the radio is
enabled again after the higher layers actually decided to shut it
off.
This also pulls out this common RF-kill checking code into a common
function called by both transport generations and also moves it to
the direct method - in the internal helper we don't really care
about the RF-kill status anymore since we won't report it up until
the stop anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the context info fails to be allocated, the mutex
isn't unlocked properly, fix that.
Fixes: eda50cde58 ("iwlwifi: pcie: add context information support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change queue allocation to be dynamic. On transport init only
the command queue is being allocated. Other queues are allocated
on demand.
This is due to the huge amount of queues we will soon enable (512)
and as a preparation for TX Virtual Queue Manager feature (TVQM),
where firmware will assign the actual queue number on demand.
This includes also allocation of the byte count table per queue
and not as a contiguous chunk of memory.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function is basically the same as gen1, except for clean
ups of old devices configuration that are never used in a000
configuration.
It will also help with refactoring rf_kill later on.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Context information structure is going to be used in a000
devices for firmware self init.
The self init includes firmware self loading from DRAM by
ROM.
This means the TFH relevant firmware loading can be cleaned up.
The firmware loading includes the paging memory as well, so op
mode can stop initializing the paging and sending the DRAM_BLOCK_CMD.
Firmware is doing RFH, TFH and SCD configuration, while driver
only fills the required configurations and addresses in the
context information structure.
The only remaining access to RFH is the write pointer, which
is updated upon alive interrupt after FW configured the RFH.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
