Add a new function bnxt_alloc_vf_rep() to allocate a VF representor.
This function will be needed in subsequent patches to recreate the
VF reps after error recovery.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After probe is successful, interface may not be bought up in all
the cases and health register mapping could be invalid if firmware
undergoes reset. Fix it by invalidating the health register at the
end of probe. It will be remapped during ifup.
Fixes: 43a440c400 ("bnxt_en: Improve the status_reliable flag in bp->fw_health.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The retry loop in bnxt_try_recover_fw() should not abort when the
health register value is 0. It is a valid value that indicates the
firmware is booting up.
Fixes: 861aae786f ("bnxt_en: Enhance retry of the first message to the firmware.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset_prepare and reset_done calls have a null pointer check
on ae_dev however ae_dev is being dereferenced via the call to
ns3_is_phys_func with the ae->pdev argument. Fix this by performing
a null pointer check on ae_dev and hence short-circuiting the
dereference to ae_dev on the call to ns3_is_phys_func.
Addresses-Coverity: ("Dereference before null check")
Fixes: 715c58e94f ("net: hns3: add suspend and resume pm_ops")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shifting of the u8 integers rq->caching by 26 bits to
the left will be promoted to a 32 bit signed int and then
sign-extended to a u64. In the event that rq->caching is
greater than 0x1f then all then all the upper 32 bits of
the u64 end up as also being set because of the int
sign-extension. Fix this by casting the u8 values to a
u64 before the 26 bit left shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 4863dea3fa ("net: Adding support for Cavium ThunderX network controller")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shifting of the u8 integers f->fs.nat_lip[] by 24 bits to
the left will be promoted to a 32 bit signed int and then
sign-extended to a u64. In the event that the top bit of the u8
is set then all then all the upper 32 bits of the u64 end up as
also being set because of the sign-extension. Fix this by
casting the u8 values to a u64 before the 24 bit left shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 12b276fbf6 ("cxgb4: add support to create hash filters")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
This pr contains changes from mlx5-next branch,
already reviewed on netdev and rdma mailing lists, links below.
1) From Leon, Dynamically assign MSI-X vectors count
Already Acked by Bjorn Helgaas.
https://patchwork.kernel.org/project/netdevbpf/cover/20210314124256.70253-1-leon@kernel.org/
2) Cleanup series:
https://patchwork.kernel.org/project/netdevbpf/cover/20210311070915.321814-1-saeed@kernel.org/
From Mark, E-Switch cleanups and refactoring, and the addition
of single FDB mode needed HW bits.
From Mikhael, Remove unused struct field
From Saeed, Cleanup W=1 prototype warning
From Zheng, Esw related cleanup
From Tariq, User order-0 page allocation for EQs
====================
* mlx5-next:
net/mlx5: Implement sriov_get_vf_total_msix/count() callbacks
net/mlx5: Dynamically assign MSI-X vectors count
net/mlx5: Add dynamic MSI-X capabilities bits
PCI/IOV: Add sysfs MSI-X vector assignment interface
net/mlx5: Use order-0 allocations for EQs
net/mlx5: Add IFC bits needed for single FDB mode
net/mlx5: E-Switch, Refactor send to vport to be more generic
RDMA/mlx5: Use representor E-Switch when getting netdev and metadata
net/mlx5: E-Switch, Add eswitch pointer to each representor
net/mlx5: E-Switch, Add match on vhca id to default send rules
net/mlx5: Remove unused mlx5_core_health member recover_work
net/mlx5: simplify the return expression of mlx5_esw_offloads_pair()
net/mlx5: Cleanup prototype warning
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Check within geneve_xmit_skb/geneve6_xmit_skb that sk_buff structure
is large enough to include IPv4 or IPv6 header, and reject if not. The
geneve_xmit_skb portion and overall idea was contributed by Eric Dumazet.
Fixes a KMSAN-found uninit-value bug reported by syzbot at:
https://syzkaller.appspot.com/bug?id=abe95dc3e3e9667fc23b8d81f29ecad95c6f106f
Suggested-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+2e406a9ac75bb71d4b7a@syzkaller.appspotmail.com
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the probe fails, we must disable the regulator that was previously
enabled.
This patch is a follow-up to commit ac88c531a5
("net: davicom: Fix regulator not turned off on failed probe") which missed
one case.
Fixes: 7994fe55a4 ("dm9000: Add regulator and reset support to dm9000")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the SC7280 SoC, which includes IPA version 4.11.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the SDX55 SoC, which includes IPA version 4.5.
Starting with IPA v4.5, a few of the memory regions have a different
number of "canary" values; update comments in the where the region
identifers are defined to accurately reflect that.
I'll note three differences in SDX55 versus the other two existing
platforms (SDM845 and SC7180):
- SDX55 uses a 32-bit Linux kernel
- SDX55 has four interconnects rather than three
- SDX55 uses IPA v4.5, which uses inline checksum offload
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checksum offload for IPA v4.5+ is implemented differently, using
"inline" offload (which uses a common header format for both upload
and download offload).
The IPA hardware must be programmed to enable MAP checksum offload,
but the RMNet driver is responsible for interpreting checksum
metadata supplied with messages.
Currently, the RMNet driver does not support inline checksum offload.
This support is imminent, but until it is available, do not allow
newer versions of IPA to specify checksum offload for endpoints.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch, when enabling GRO, locally generated
TCP traffic experiences some measurable overhead, as it traverses
the GRO engine without any chance of aggregation.
This change refine the NAPI receive path admission test, to avoid
unnecessary GRO overhead in most scenarios, when GRO is enabled
on a veth peer.
Only skbs that are eligible for aggregation enter the GRO layer,
the others will go through the traditional receive path.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the veth device has the GRO feature bit set, even if
no GRO aggregation is possible with the default configuration,
as the veth device does not hook into the GRO engine.
Flipping the GRO feature bit from user-space is a no-op, unless
XDP is enabled. In such scenario GRO could actually take place, but
TSO is forced to off on the peer device.
This change allow user-space to really control the GRO feature, with
no need for an XDP program.
The GRO feature bit is now cleared by default - so that there are no
user-visible behavior changes with the default configuration.
When the GRO bit is set, the per-queue NAPI instances are initialized
and registered. On xmit, when napi instances are available, we try
to use them.
Some additional checks are in place to ensure we initialize/delete NAPIs
only when needed in case of overlapping XDP and GRO configuration
changes.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As described by commit 9c4c325252 ("skbuff: preserve sock
reference when scrubbing the skb."), orphaning a skb
in the TX path will cause OoO.
Let's use skb_orphan_partial() instead of skb_orphan(), so
that we keep the sk around for queue's selection sake and we
still avoid the problem fixed with commit 4bf9ffa0fb ("veth:
Orphan skb before GRO")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new netlink API for reading SFP data requires a new op to be
implemented. The idea of the new netlink SFP code is that userspace is
responsible to parsing the EEPROM data and requesting pages, rather
than have the kernel decide what pages are interesting and returning
them. This allows greater flexibility for newer formats.
Currently the generic SFP code only supports simple SFPs. Allow i2c
address 0x50 and 0x51 to be accessed with page and bank must always be
0. This interface will later be extended when for example QSFP support
is added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the driver to recognise DSFP transceiver module ID and therefore
allow its EEPROM dumps using ethtool.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ethtool_ops::get_module_eeprom_by_page() to enable
support of new SFP standards.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare for ethtool_ops::get_module_eeprom_data() implementation by
extracting common part of mlx5_query_module_eeprom() into a separate
function.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dwell time for the scan is not configurable according to the current
firmware submitted into linux-firmware.git, so leave the dwell time 0 to
indicate the dwell time always determined by the firmware.
Fixes: 399090ef96 ("mt76: mt76_connac: move hw_scan and sched_scan routine in mt76_connac_mcu module")
Suggested-by: Soul Huang <Soul.Huang@mediatek.com>
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the Wake-on-WoWLAN failure should rely on ARP Information is being
updated in time to the firmware.
Fixes: ffa1bf9742 ("mt76: mt7921: introduce PM support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce MT_WFDMA_DUMMY_CR definition and remove magic numbers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reset wifi subsystem when MCU is already running.
Fixes firmware download failure after soft reboot on systems where the PCIe
reset could not be performed properly.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Co-developed-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ieee80211_beacon_get_template() returns NULL when beacon state is disabled.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ieee80211_beacon_get_template() returns NULL when beacon state is disabled,
so beacon_offload cannot be disabled for some devices.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rework mt7921_mcu_debug_msg_event routing removing unnecessary
assignments and relying on wiphy_info
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make sure the mcu is not in sleep mode before sending mcu messages in
mt7921_remove_interface routine.
Fixes: 1d8efc741d ("mt76: mt7921: introduce Runtime PM support")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to the mt7915 driver, deleting a key with the previous key index
deletes the current key. Rework the code to better keep track of
multiple keys and check for the key index before deleting the current
key
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix incorrect txpower init value for TSSI off chips which causes
too small txpower.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Guobin Huang <huangguobin4@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
After chip reset, the DMA scheduler needs to be initialized as well.
Since the code is PCI/SoC specific, move it to pci_mac.c, so that it
can depend on a function in dma.c
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The same as mt7615. Keep BSS_INFO_BASIC enabled throughout interfaces
life cycle.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
BSS_INFO_BASIC is never called alone with inactive state, which always
follows beacon offload disable, so keep it enabled throughout interfaces
life cycle. Inactive state also removes sta record of all connected
stations, thurs causes connection lost which defeats the purpose of CSA.
Lastly, this is especially an unexpected behavior that keeping mt7622
failing beacon buffer recyled when scanning channels.
bss_conf change is updated with active state only, so just overwrite it.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
hif interrupt needs to be triggered after MT_MCU_INT_EVENT.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With this patch, mt7615_mac_reset_work() can recover system back.
Fixes: e637763b60 ("mt76: move mcu queues to mt76_dev q_mcu array")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Properly configure rcpi based on association process rssi. rcpi is used
by rate controller embedded into the fw to initialize amsdu size.
Tested-by: Jayden.Kuo <jayden.kuo@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_sta_cmd_info data structure to contain parameters passed
to mt76_sta_cmd_info routine. This is preliminary patch to properly
configure rcpi for mt7921 devices.
Tested-by: Jayden.Kuo <jayden.kuo@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get rid of mt7921_mac_wtbl_lmac_addr routine since mt7921 wtbl size is
19 entries
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When disassociating and clearing the BSSID of a repeater entry used by a client
mode interface, the corresponding MAC address entry can get lost too, causing
the client interface to not be able to associate anymore.
Fix this by also refreshing the MAC address when setting the BSSID
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Deleting a key with the previous key index deletes the current key
Rework the code to better keep track of multiple keys and check for the
key index before deleting the current key
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mcu definitions already available in mt76_connac_mcu.h
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently in the switch statement case where type is
NL80211_IFTYPE_STATION there is a check to see if type
is not NL80211_IFTYPE_STATION. This check is always false
and is redundant dead code that can be removed.
Addresses-Coverity: ("Logically dead code")
Fixes: e0f9fdda81 ("mt76: mt7921: add ieee80211_ops")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove leftovers from dbdc configuration since mt7921
does not support it.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce wifi chip reset support for mt7921 device to recover mcu
hangs.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Export mt76_dma_rx_cleanup routine in mt76_queue_ops data structure.
This is a preliminary patch to introduce mt7921 chip reset support.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
