typec_register_partner() does not guarantee partner registration
to always succeed. In the event of failure, port->partner is set
to the error value or NULL. Given that port->partner validity is
not checked, this results in the following crash:
Unable to handle kernel NULL pointer dereference at virtual address xx
pc : run_state_machine+0x1bc8/0x1c08
lr : run_state_machine+0x1b90/0x1c08
..
Call trace:
run_state_machine+0x1bc8/0x1c08
tcpm_state_machine_work+0x94/0xe4
kthread_worker_fn+0x118/0x328
kthread+0x1d0/0x23c
ret_from_fork+0x10/0x20
To prevent the crash, check for port->partner validity before
derefencing it in all the call sites.
Cc: stable@vger.kernel.org
Fixes: c97cd0b4b5 ("usb: typec: tcpm: set initial svdm version based on pd revision")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240427202812.3435268-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before sending Enter Mode for an Alt Mode, there is a gap between Discover
Modes and the Alt Mode driver queueing the Enter Mode VDM for the port
partner to send a message to the port.
If this message results in unregistering Alt Modes such as in a DR_SWAP,
then the following deadlock can occur with respect to the DisplayPort Alt
Mode driver:
1. The DR_SWAP state holds port->lock. Unregistering the Alt Mode driver
results in a cancel_work_sync() that waits for the current dp_altmode_work
to finish.
2. dp_altmode_work makes a call to tcpm_altmode_enter. The deadlock occurs
because tcpm_queue_vdm_unlock attempts to hold port->lock.
Before attempting to grab the lock, ensure that the port is in a state
vdm_run_state_machine can run in. Alt Mode unregistration will not occur
in these states.
Fixes: 03eafcfb60 ("usb: typec: tcpm: Add tcpm_queue_vdm_unlocked() helper")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240423202356.3372314-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a Fast Role Swap control message attempt results in a transition
to ERROR_RECOVERY, the TCPC can still queue a TCPM_SOURCING_VBUS event.
If the event is queued but processed after the tcpm_reset_port() call
in the PORT_RESET state, then the following occurs:
1. tcpm_reset_port() calls tcpm_init_vbus() to reset the vbus sourcing and
sinking state
2. tcpm_pd_event_handler() turns VBUS on before the port is in the default
state.
3. The port resolves as a sink. In the SNK_DISCOVERY state,
tcpm_set_charge() cannot set vbus to charge.
Clear pd events within PORT_RESET to get rid of non-applicable events.
Fixes: b17dd57118 ("staging: typec: tcpm: Improve role swap with non PD capable partners")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240423202715.3375827-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move disabling of the vdd-pdphy supply to the start() function which
enabled it for symmetry and to make sure that it is disabled as intended
in all error paths of pmic_typec_pdphy_reset() (i.e. not just when
qcom_pmic_typec_pdphy_enable() fails).
Cc: stable+noautosel@kernel.org # Not needed in any stable release, just a minor bugfix
Fixes: a4422ff221 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240418145730.4605-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to stop and deregister the port in case of late probe errors
to avoid use-after-free issues when the underlying memory is released by
devres.
Fixes: a4422ff221 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Cc: stable@vger.kernel.org # 6.5
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240418145730.4605-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ChipID bytes are read in inverse order: invert the ChipID value
defined as IT5205FN_CHIP_ID and used for validating the same.
Fixes: 41fe9ea169 ("usb: typec: mux: Add ITE IT5205 Alternate Mode Passive MUX driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240409113646.305105-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Off-by-one errors happen because nr_snk_pdo and nr_src_pdo are
incorrectly added one. The index of the loop is equal to the number of
PDOs to be updated when leaving the loop and it doesn't need to be added
one.
When doing the power negotiation, TCPM relies on the "nr_snk_pdo" as
the size of the local sink PDO array to match the Source capabilities
of the partner port. If the off-by-one overflow occurs, a wrong RDO
might be sent and unexpected power transfer might happen such as over
voltage or over current (than expected).
"nr_src_pdo" is used to set the Rp level when the port is in Source
role. It is also the array size of the local Source capabilities when
filling up the buffer which will be sent as the Source PDOs (such as
in Power Negotiation). If the off-by-one overflow occurs, a wrong Rp
level might be set and wrong Source PDOs will be sent to the partner
port. This could potentially cause over current or port resets.
Fixes: cd099cde4e ("usb: typec: tcpm: Support multiple capabilities")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240404133517.2707955-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix issues when initially checking for a connector change:
- Use the correct connector number not the entire CCI.
- Call ->read under the PPM lock.
- Remove a bogus READ_ONCE.
Fixes: 808a8b9e0b ("usb: typec: ucsi: Check for notifications after init")
Cc: stable@kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240401210515.1902048-1-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the UCSI_CAP_GET_PD_MESSAGE bit before sending GET_PD_MESSAGE to
discover partner and cable identity, check UCSI_CAP_CABLE_DETAILS before
sending GET_CABLE_PROPERTY to discover the cable and check
UCSI_CAP_ALT_MODE_DETAILS before registering the a cable plug. Additionally,
move 8 bits from reserved_1 to features in the ucsi_capability struct. This
makes the field 16 bits, still 8 short of the 24 bits allocated for it in
UCSI v3.0, but it will not overflow because UCSI only defines 14 bits in
bmOptionalFeatures.
Fixes: 38ca416597 ("usb: typec: ucsi: Register cables based on GET_CABLE_PROPERTY")
Link: https://lore.kernel.org/linux-usb/44e8142f-d9b3-487b-83fe-39deadddb492@linaro.org
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jameson Thies <jthies@google.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240315171836.343830-2-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the UCSI_CCI_RESET_COMPLETE complete flag before starting
another reset. Use a UCSI_SET_NOTIFICATION_ENABLE command to clear
the flag if it is set.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-6-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DELL systems don't like UCSI_ACK_CC_CI commands with the
UCSI_ACK_CONNECTOR_CHANGE but not the UCSI_ACK_COMMAND_COMPLETE
bit set. The current quirk still leaves room for races because
it requires two consecutive ACK commands to be sent.
Refactor and significantly simplify the quirk to fix this:
Send a dummy command and bundle the connector change ack with the
command completion ack in a single UCSI_ACK_CC_CI command.
This removes the need to probe for the quirk.
While there define flag bits for struct ucsi_acpi->flags in ucsi_acpi.c
and don't re-use definitions from ucsi.h for struct ucsi->flags.
Fixes: f3be347ea4 ("usb: ucsi_acpi: Quirk to ack a connector change ack cmd")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-5-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a command completes the OPM must send an ack. This applies
to unsupported commands, too.
Send the required ACK for unsupported commands.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-4-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The completion notification for the final SET_NOTIFICATION_ENABLE
command during initialization can include a connector change
notification. However, at the time this completion notification is
processed, the ucsi struct is not ready to handle this notification.
As a result the notification is ignored and the controller
never sends an interrupt again.
Re-check CCI for a pending connector state change after
initialization is complete. Adjust the corresponding debug
message accordingly.
Fixes: 71a1fa0df2 ("usb: typec: ucsi: Store the notification mask")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suppose we sleep on the PPM lock after clearing the EVENT_PENDING
bit because the thread for another connector is executing a command.
In this case the command completion of the other command will still
report the connector change for our connector.
Clear the EVENT_PENDING bit under the PPM lock to avoid another
useless call to ucsi_handle_connector_change() in this case.
Fixes: c9aed03a0a ("usb: ucsi: Add missing ppm_lock")
Cc: stable <stable@kernel.org>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The attribute writing should return the number of bytes used from the
buffer on success.
Fixes: a7cff92f06 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240319074309.3306579-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PD of Type-C port needs to be updated in pd_set. Unlink the Type-C
port device to the old PD before linking it to a new one.
Fixes: cd099cde4e ("usb: typec: tcpm: Support multiple capabilities")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240311172306.3911309-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unregister pd capabilitie in tcpm, KASAN will capture below double
-free issue. The root cause is the same capabilitiy will be kfreed twice,
the first time is kfreed by pd_capabilities_release() and the second time
is explicitly kfreed by tcpm_port_unregister_pd().
[ 3.988059] BUG: KASAN: double-free in tcpm_port_unregister_pd+0x1a4/0x3dc
[ 3.995001] Free of addr ffff0008164d3000 by task kworker/u16:0/10
[ 4.001206]
[ 4.002712] CPU: 2 PID: 10 Comm: kworker/u16:0 Not tainted 6.8.0-rc5-next-20240220-05616-g52728c567a55 #53
[ 4.012402] Hardware name: Freescale i.MX8QXP MEK (DT)
[ 4.017569] Workqueue: events_unbound deferred_probe_work_func
[ 4.023456] Call trace:
[ 4.025920] dump_backtrace+0x94/0xec
[ 4.029629] show_stack+0x18/0x24
[ 4.032974] dump_stack_lvl+0x78/0x90
[ 4.036675] print_report+0xfc/0x5c0
[ 4.040289] kasan_report_invalid_free+0xa0/0xc0
[ 4.044937] __kasan_slab_free+0x124/0x154
[ 4.049072] kfree+0xb4/0x1e8
[ 4.052069] tcpm_port_unregister_pd+0x1a4/0x3dc
[ 4.056725] tcpm_register_port+0x1dd0/0x2558
[ 4.061121] tcpci_register_port+0x420/0x71c
[ 4.065430] tcpci_probe+0x118/0x2e0
To fix the issue, this will remove kree() from tcpm_port_unregister_pd().
Fixes: cd099cde4e ("usb: typec: tcpm: Support multiple capabilities")
cc: stable@vger.kernel.org
Suggested-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240311065219.777037-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When orientation switch is enabled in ucsi glink, there is a xhci
probe failure seen when booting up in host mode in reverse
orientation.
During bootup the following things happen in multiple drivers:
a) DWC3 controller driver initializes the core in device mode when the
dr_mode is set to DRD. It relies on role_switch call to change role to
host.
b) QMP driver initializes the lanes to TYPEC_ORIENTATION_NORMAL as a
normal routine. It relies on the typec_switch_set call to get notified
of orientation changes.
c) UCSI core reads the UCSI_GET_CONNECTOR_STATUS via the glink and
provides initial role switch to dwc3 controller.
When booting up in host mode with orientation TYPEC_ORIENTATION_REVERSE,
then we see the following things happening in order:
a) UCSI gives initial role as host to dwc3 controller ucsi_register_port.
Upon receiving this notification, the dwc3 core needs to program GCTL from
PRTCAP_DEVICE to PRTCAP_HOST and as part of this change, it asserts GCTL
Core soft reset and waits for it to be completed before shifting it to
host. Only after the reset is done will the dwc3_host_init be invoked and
xhci is probed. DWC3 controller expects that the usb phy's are stable
during this process i.e., the phy init is already done.
b) During the 100ms wait for GCTL core soft reset, the actual notification
from PPM is received by ucsi_glink via pmic glink for changing role to
host. The pmic_glink_ucsi_notify routine first sends the orientation
change to QMP and then sends role to dwc3 via ucsi framework. This is
happening exactly at the time GCTL core soft reset is being processed.
c) When QMP driver receives typec switch to TYPEC_ORIENTATION_REVERSE, it
then re-programs the phy at the instant GCTL core soft reset has been
asserted by dwc3 controller due to which the QMP PLL lock fails in
qmp_combo_usb_power_on.
d) After the 100ms of GCTL core soft reset is completed, the dwc3 core
goes for initializing the host mode and invokes xhci probe. But at this
point the QMP is non-responsive and as a result, the xhci plat probe fails
during xhci_reset.
Fix this by passing orientation switch to available ucsi instances if
their gpio configuration is available before ucsi_register is invoked so
that by the time, the pmic_glink_ucsi_notify provides typec_switch to QMP,
the lane is already configured and the call would be a NOP thus not racing
with role switch.
Cc: stable@vger.kernel.org
Fixes: c6165ed2f4 ("usb: ucsi: glink: use the connector orientation GPIO to provide switch events")
Suggested-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240301040914.458492-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In tcpm_pd_set, the array of port source capabilities is port->src_pdo,
not port->snk_pdo.
Fixes: cd099cde4e ("usb: typec: tcpm: Support multiple capabilities")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240311144500.3694849-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt changes for 6.9-rc1. Lots of
tiny changes and forward progress to support new hardware and better
support for existing devices. Included in here are:
- Thunderbolt (i.e. USB4) updates for newer hardware and uses as more
people start to use the hardware
- default USB authentication mode Kconfig and documentation update to
make it more obvious what is going on
- USB typec updates and enhancements
- usual dwc3 driver updates
- usual xhci driver updates
- function USB (i.e. gadget) driver updates and additions
- new device ids for lots of drivers
- loads of other small updates, full details in the shortlog
All of these, including a "last minute regression fix" have been in
linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZfwpzA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymS9QCdEuF6KJFLOrDrGS4NbZNSUPIVF6oAn350r4NX
CMZah37Dfr1VDCOOV4gQ
=HACL
-----END PGP SIGNATURE-----
Merge tag 'usb-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.9-rc1. Lots
of tiny changes and forward progress to support new hardware and
better support for existing devices. Included in here are:
- Thunderbolt (i.e. USB4) updates for newer hardware and uses as more
people start to use the hardware
- default USB authentication mode Kconfig and documentation update to
make it more obvious what is going on
- USB typec updates and enhancements
- usual dwc3 driver updates
- usual xhci driver updates
- function USB (i.e. gadget) driver updates and additions
- new device ids for lots of drivers
- loads of other small updates, full details in the shortlog
All of these, including a "last minute regression fix" have been in
linux-next with no reported issues"
* tag 'usb-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (185 commits)
usb: usb-acpi: Fix oops due to freeing uninitialized pld pointer
usb: gadget: net2272: Use irqflags in the call to net2272_probe_fin
usb: gadget: tegra-xudc: Fix USB3 PHY retrieval logic
phy: tegra: xusb: Add API to retrieve the port number of phy
USB: gadget: pxa27x_udc: Remove unused of_gpio.h
usb: gadget/snps_udc_plat: Remove unused of_gpio.h
usb: ohci-pxa27x: Remove unused of_gpio.h
usb: sl811-hcd: only defined function checkdone if QUIRK2 is defined
usb: Clarify expected behavior of dev_bin_attrs_are_visible()
xhci: Allow RPM on the USB controller (1022:43f7) by default
usb: isp1760: remove SLAB_MEM_SPREAD flag usage
usb: misc: onboard_hub: use pointer consistently in the probe function
usb: gadget: fsl: Increase size of name buffer for endpoints
usb: gadget: fsl: Add of device table to enable module autoloading
usb: typec: tcpm: add support to set tcpc connector orientatition
usb: typec: tcpci: add generic tcpci fallback compatible
dt-bindings: usb: typec-tcpci: add tcpci fallback binding
usb: gadget: fsl-udc: Replace custom log wrappers by dev_{err,warn,dbg,vdbg}
usb: core: Set connect_type of ports based on DT node
dt-bindings: usb: Add downstream facing ports to realtek binding
...
The driver already support the tcpci binding for the i2c_device_id so
add the support for the of_device_id too.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240222210903.208901-3-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DisplayPort driver's sysfs nodes may be present to the userspace before
typec_altmode_set_drvdata() completes in dp_altmode_probe. This means that
a sysfs read can trigger a NULL pointer error by deferencing dp->hpd in
hpd_show or dp->lock in pin_assignment_show, as dev_get_drvdata() returns
NULL in those cases.
Remove manual sysfs node creation in favor of adding attribute group as
default for devices bound to the driver. The ATTRIBUTE_GROUPS() macro is
not used here otherwise the path to the sysfs nodes is no longer compliant
with the ABI.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Link: https://lore.kernel.org/r/20240229001101.3889432-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register SOP' alternate modes with a Type-C Connector Class cable plug.
Alternate modes are queried from the PPM using the GET_ALTERNATE_MODES
command with recipient set to SOP'.
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jameson Thies <jthies@google.com>
Link: https://lore.kernel.org/r/20240305025804.1290919-5-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register SOP and SOP' Discover Identity responses with the USB Type-C
Connector Class as partner and cable identities, respectively. Discover
Identity responses are requested from the PPM using the GET_PD_MESSAGE
UCSI command.
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20240305025804.1290919-4-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register cables with the Type-C Connector Class in the UCSI driver based
on the PPM response to GET_CABLE_PROPERTY. Registered cable properties
include plug type, cable type and major revision.
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jameson Thies <jthies@google.com>
Link: https://lore.kernel.org/r/20240305025804.1290919-3-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While commit 69f89168b3 ("usb: typec: tpcm: Fix issues with power being
removed during reset") fixes the boot issues for bus powered devices such
as LibreTech Renegade Elite/Firefly, it trades off the CC pins NOT being
Hi-Zed during errory recovery (i.e PORT_RESET) for devices which are NOT
bus powered(a.k.a self powered). This change Hi-Zs the CC pins only for
self powered devices, thus preventing brown out for bus powered devices
Adhering to spec is gaining more importance due to the Common charger
initiative enforced by the European Union.
Quoting from the spec:
4.5.2.2.2.1 ErrorRecovery State Requirements
The port shall not drive VBUS or VCONN, and shall present a
high-impedance to ground (above zOPEN) on its CC1 and CC2 pins.
Hi-Zing the CC pins is the inteded behavior for PORT_RESET.
CC pins are set to default state after tErrorRecovery in
PORT_RESET_WAIT_OFF.
4.5.2.2.2.2 Exiting From ErrorRecovery State
A Sink shall transition to Unattached.SNK after tErrorRecovery.
A Source shall transition to Unattached.SRC after tErrorRecovery.
Fixes: 69f89168b3 ("usb: typec: tpcm: Fix issues with power being removed during reset")
Cc: stable@vger.kernel.org
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240228000512.746252-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SM8550 and SM8650 Qualcomm platforms a call to UCSI_GET_PDOS for
non-PD partners will cause a firmware crash with no
easy way to recover from it.
Add UCSI_NO_PARTNER_PDOS quirk for those platform until we find
a way to properly handle the crash.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240223-topic-sm8550-upstream-ucsi-no-pdos-v1-1-8900ad510944@linaro.org
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the port is setting the pin configuration when no configuration is
chosen, the DisplayPort driver will not send Configure to the cable plug
if it's available. Add transition to DP_STATE_CONFIGURE_PRIME.
Fixes: 71ba4fe566 ("usb: typec: altmodes/displayport: add SOP' support")
Signed-off-by: RD Babiera <rdbabiera@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240223002302.3937235-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Smatch checker flags svdm_version being uninitialized for Discover
Identity Messages within tcpm_pd_svdm for the CMDT_INIT case. Cable plugs
cannot initialize SVDM commands, however a port partner that isn't allowed
to communicate over SOP' could, which would result in the CMDT_INIT block
running for a received SOP' message.
First, initialize svdm_version for the TCPC_TX_SOP_PRIME case. If the
svdm_version returns as an error, we expect the received svdm to be the
result of Discover Identity that updates the value accordingly.
Next, drop all SOP' messages of type CMDT_INIT within tcpm_pd_svdm.
Finally, remove redundant call that assigns modep and pdev. Smatch will
raise an uninitialized symbol error over modep_prime and pdev_prime, but
both the assignment and use of these variables are guarded behind
a check for rx_sop_type == TCPC_TX_SOP_PRIME.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/a432603b-b801-4001-b309-247dded707d3@moroto.mountain/
Fixes: fb7ff25ae4 ("usb: typec: tcpm: add discover identity support for SOP'")
Signed-off-by: RD Babiera <rdbabiera@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240223002233.3936275-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 43a7206b09 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the structures typec_mux_class, retimer_class and
typec_class to be declared at build time placing them into read-only
memory, instead of having to be dynamically allocated at boot time.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240301-class_cleanup-usb-v1-1-50309e325095@marliere.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need it here for the USB fixes, and it resolves a merge conflict as
reported in linux-next in drivers/usb/roles/class.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the merge of b717dfbf73 ("Revert "usb: typec: tcpm: fix
cc role at port reset"") into mainline the LibreTech Renegade
Elite/Firefly has died during boot, the main symptom observed in testing
is a sudden stop in console output. Gábor Stefanik identified in review
that the patch would cause power to be removed from devices without
batteries (like this board), observing that while the patch is correct
according to the spec this appears to be an oversight in the spec.
Given that the change makes previously working systems unusable let's
revert it, there was some discussion of identifying systems that have
alternative power and implementing the standards conforming behaviour in
only that case.
Fixes: b717dfbf73 ("Revert "usb: typec: tcpm: fix cc role at port reset"")
Cc: stable <stable@kernel.org>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240212-usb-fix-renegade-v1-1-22c43c88d635@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit aed65af1cc ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move all the
device_type variables in use by the driver to be constant structures as
well, placing it into read-only memory which can not be modified at
runtime.
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240218-device_cleanup-usb-v1-1-77423c4da262@marliere.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reverted commit makes the state machine only ever go from SRC_ATTACH_WAIT
to SNK_TRY in endless loop when toggling. After revert it goes to SRC_ATTACHED
after initially trying SNK_TRY earlier, as it should for toggling to ever detect
the power source mode and the port is again able to provide power to attached
power sinks.
This reverts commit 2d6d801270.
Cc: stable@vger.kernel.org
Fixes: 2d6d801270 ("usb: typec: tcpm: reset counter when enter into unattached state after try role")
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20240217162023.1719738-1-megi@xff.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PMI632 PMIC support Type-C port handling, but lacks USB
PowerDelivery support. The TCPM requires all callbacks to be provided
by the implementation. Implement a special, 'stub' Qcom PD PHY
implementation to enable the PMI632 support.
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # sdm632-fairphone-fp3
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240130-pmi632-typec-v3-3-b05fe44f0a51@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PD major revision for the port partner is described in
GET_CONNECTOR_CAPABILITY and is only valid on UCSI 2.0 and newer. Update
the pd_revision on the partner if the UCSI version is 2.0 or newer.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Link: https://lore.kernel.org/r/20240209143723.v5.3.Idf7d373c3cbb54058403cb951d644f1f09973d15@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the data structures for ucsi_connector_capability and
ucsi_connector_status to UCSIv3.
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Link: https://lore.kernel.org/r/20240209143723.v5.2.I3d909e3c9a200621e3034686f068a3307945fd87@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Between UCSI 1.2 and UCSI 2.0, the size of the MESSAGE_IN region was
increased from 16 to 256. In order to avoid overflowing reads for older
systems, add a mechanism to use the read UCSI version to truncate read
sizes on UCSI v1.2.
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Link: https://lore.kernel.org/r/20240209143723.v5.1.Iacf5570a66b82b73ef03daa6557e2fc0db10266a@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The QCM6490 Linux Android firmware needs this workaround as well. Add it
to the list.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240208-fp5-pmic-glink-v2-2-4837d4abd5a4@fairphone.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Follow the PD PHY changes and rework Type-C port implementation to
become an encapsulated backend. While this is not required for the
PMI632, it will us later to enable Type-C handling on earlier platforms,
including, but not limited to SDM845, SDM660 and MSM8998.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-8-182d9aa0a5b3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework Qualcomm PMIC TCPM driver to allow different platform-specific
implementations of the PD PHY interface. While majority of platforms
has the same of register for the PD PHY, some obscure ones (PMI632) do
not have real PD PHY support. Add proper interface between the main
module and the PD PHY backend to allow switching the PD PHY
implementation.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-7-182d9aa0a5b3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function qcom_pmic_typec_set_roles() passes enum values as boolean
values to qcom_pmic_typec_pdphy_set_roles(), which then interprets them
as bit values. Be more explicit about it, pass enum values directly and
compute corresponding bit masks in qcom_pmic_typec_pdphy_set_roles().
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-6-182d9aa0a5b3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the PD is disabled for the port, port->pds will be left as NULL,
which causes the following crash during caps intilisation. Fix the
crash.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
tcpm_register_port+0xaec/0xc44
qcom_pmic_typec_probe+0x1a4/0x254
platform_probe+0x68/0xc0
really_probe+0x148/0x2ac
__driver_probe_device+0x78/0x12c
driver_probe_device+0xd8/0x160
Bluetooth: hci0: QCA Product ID :0x0000000a
__device_attach_driver+0xb8/0x138
bus_for_each_drv+0x80/0xdc
Bluetooth: hci0: QCA SOC Version :0x40020150
__device_attach+0x9c/0x188
device_initial_probe+0x14/0x20
bus_probe_device+0xac/0xb0
deferred_probe_work_func+0x8c/0xc8
process_one_work+0x1ec/0x51c
worker_thread+0x1ec/0x3e4
kthread+0x120/0x124
ret_from_fork+0x10/0x20
Fixes: cd099cde4e ("usb: typec: tcpm: Support multiple capabilities")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-5-182d9aa0a5b3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PPM on some Dell laptops seems to expect that the ACK_CC_CI
command to clear the connector change notification is in turn
followed by another ACK_CC_CI to acknowledge the ACK_CC_CI command
itself. This is in violation of the UCSI spec that states:
"The only notification that is not acknowledged by the OPM is
the command completion notification for the ACK_CC_CI or the
PPM_RESET command."
Add a quirk to send this ack anyway.
Apply the quirk to all Dell systems.
On the first command that acks a connector change send a dummy
command to determine if it runs into a timeout. Only activate
the quirk if it does. This ensure that we do not break Dell
systems that do not need the quirk.
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-4-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of a spurious or otherwise delayed notification it is
possible that CCI still reports the previous completion. The
UCSI spec is aware of this and provides two completion bits in
CCI, one for normal commands and one for acks. As acks and commands
alternate the notification handler can determine if the completion
bit is from the current command.
The initial UCSI code correctly handled this but the distinction
between the two completion bits was lost with the introduction of
the new API.
To fix this revive the ACK_PENDING bit for ucsi_acpi and only complete
commands if the completion bit matches.
Fixes: f56de278e8 ("usb: typec: ucsi: acpi: Move to the new API")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
