Currently, if a process starts a transaction and then takes an
exception because the FPU, VMX or VSX unit is unavailable to it,
we end up corrupting any FP/VMX/VSX state that was valid before
the interrupt. For example, if the process starts a transaction
with the FPU available to it but VMX unavailable, and then does
a VMX instruction inside the transaction, the FP state gets
corrupted.
Loading up the desired state generally involves doing a reclaim
and a recheckpoint. To avoid corrupting already-valid state, we have
to be careful not to reload that state from the thread_struct
between the reclaim and the recheckpoint (since the thread_struct
values are stale by now), and we have to reload that state from
the transact_fp/vr arrays after the recheckpoint to get back the
current transactional values saved there by the reclaim.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, when we have a process using the transactional memory
facilities on POWER8 (that is, the processor is in transactional
or suspended state), and the process enters the kernel and the
kernel then uses the floating-point or vector (VMX/Altivec) facility,
we end up corrupting the user-visible FP/VMX/VSX state. This
happens, for example, if a page fault causes a copy-on-write
operation, because the copy_page function will use VMX to do the
copy on POWER8. The test program below demonstrates the bug.
The bug happens because when FP/VMX state for a transactional process
is stored in the thread_struct, we store the checkpointed state in
.fp_state/.vr_state and the transactional (current) state in
.transact_fp/.transact_vr. However, when the kernel wants to use
FP/VMX, it calls enable_kernel_fp() or enable_kernel_altivec(),
which saves the current state in .fp_state/.vr_state. Furthermore,
when we return to the user process we return with FP/VMX/VSX
disabled. The next time the process uses FP/VMX/VSX, we don't know
which set of state (the current register values, .fp_state/.vr_state,
or .transact_fp/.transact_vr) we should be using, since we have no
way to tell if we are still in the same transaction, and if not,
whether the previous transaction succeeded or failed.
Thus it is necessary to strictly adhere to the rule that if FP has
been enabled at any point in a transaction, we must keep FP enabled
for the user process with the current transactional state in the
FP registers, until we detect that it is no longer in a transaction.
Similarly for VMX; once enabled it must stay enabled until the
process is no longer transactional.
In order to keep this rule, we add a new thread_info flag which we
test when returning from the kernel to userspace, called TIF_RESTORE_TM.
This flag indicates that there is FP/VMX/VSX state to be restored
before entering userspace, and when it is set the .tm_orig_msr field
in the thread_struct indicates what state needs to be restored.
The restoration is done by restore_tm_state(). The TIF_RESTORE_TM
bit is set by new giveup_fpu/altivec_maybe_transactional helpers,
which are called from enable_kernel_fp/altivec, giveup_vsx, and
flush_fp/altivec_to_thread instead of giveup_fpu/altivec.
The other thing to be done is to get the transactional FP/VMX/VSX
state from .fp_state/.vr_state when doing reclaim, if that state
has been saved there by giveup_fpu/altivec_maybe_transactional.
Having done this, we set the FP/VMX bit in the thread's MSR after
reclaim to indicate that that part of the state is now valid
(having been reclaimed from the processor's checkpointed state).
Finally, in the signal handling code, we move the clearing of the
transactional state bits in the thread's MSR a bit earlier, before
calling flush_fp_to_thread(), so that we don't unnecessarily set
the TIF_RESTORE_TM bit.
This is the test program:
/* Michael Neuling 4/12/2013
*
* See if the altivec state is leaked out of an aborted transaction due to
* kernel vmx copy loops.
*
* gcc -m64 htm_vmxcopy.c -o htm_vmxcopy
*
*/
/* We don't use all of these, but for reference: */
int main(int argc, char *argv[])
{
long double vecin = 1.3;
long double vecout;
unsigned long pgsize = getpagesize();
int i;
int fd;
int size = pgsize*16;
char tmpfile[] = "/tmp/page_faultXXXXXX";
char buf[pgsize];
char *a;
uint64_t aborted = 0;
fd = mkstemp(tmpfile);
assert(fd >= 0);
memset(buf, 0, pgsize);
for (i = 0; i < size; i += pgsize)
assert(write(fd, buf, pgsize) == pgsize);
unlink(tmpfile);
a = mmap(NULL, size, PROT_READ|PROT_WRITE, MAP_PRIVATE, fd, 0);
assert(a != MAP_FAILED);
asm __volatile__(
"lxvd2x 40,0,%[vecinptr] ; " // set 40 to initial value
TBEGIN
"beq 3f ;"
TSUSPEND
"xxlxor 40,40,40 ; " // set 40 to 0
"std 5, 0(%[map]) ;" // cause kernel vmx copy page
TABORT
TRESUME
TEND
"li %[res], 0 ;"
"b 5f ;"
"3: ;" // Abort handler
"li %[res], 1 ;"
"5: ;"
"stxvd2x 40,0,%[vecoutptr] ; "
: [res]"=r"(aborted)
: [vecinptr]"r"(&vecin),
[vecoutptr]"r"(&vecout),
[map]"r"(a)
: "memory", "r0", "r3", "r4", "r5", "r6", "r7");
if (aborted && (vecin != vecout)){
printf("FAILED: vector state leaked on abort %f != %f\n",
(double)vecin, (double)vecout);
exit(1);
}
munmap(a, size);
close(fd);
printf("PASSED!\n");
return 0;
}
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we set irq_work on a processor and immediately afterward, before the
irq work has a chance to be processed, we change the decrementer value,
we can seriously delay the handling of that irq_work.
Fix it by checking in a few places for pending irq work, first before
changing the decrementer in decrementer_set_next_event() and after
changing it in the same function and in timer_interrupt().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Huge Dickins reported an issue that b5ff4211a8
"powerpc/book3s: Queue up and process delayed MCE events" breaks the
PowerMac G5 boot. This patch fixes it by moving the mce even processing
away from syscall exit, which was wrong to do that in first place, and
using irq work framework to delay processing of mce event.
Reported-by: Hugh Dickins <hughd@google.com
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some devices, for example PCI root port, don't have IOMMU table and
group. We needn't detach them from their IOMMU group. Otherwise, it
potentially incurs kernel crash because of referring NULL IOMMU group
as following backtrace indicates:
.iommu_group_remove_device+0x74/0x1b0
.iommu_bus_notifier+0x94/0xb4
.notifier_call_chain+0x78/0xe8
.__blocking_notifier_call_chain+0x7c/0xbc
.blocking_notifier_call_chain+0x38/0x48
.device_del+0x50/0x234
.pci_remove_bus_device+0x88/0x138
.pci_stop_and_remove_bus_device+0x2c/0x40
.pcibios_remove_pci_devices+0xcc/0xfc
.pcibios_remove_pci_devices+0x3c/0xfc
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When EEH error comes to one specific PCI device before its driver
is loaded, we will apply hotplug to recover the error. During the
plug time, the PCI device will be probed and its driver is loaded.
Then we wrongly calls to the error handlers if the driver supports
EEH explicitly.
The patch intends to fix by introducing flag EEH_DEV_NO_HANDLER and
set it before we remove the PCI device. In turn, we can avoid wrongly
calls the error handlers of the PCI device after its driver loaded.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After reset on the specific PE or PHB, we never configure AER
correctly on PowerNV platform. We needn't care it on pSeries
platform. The patch introduces additional EEH operation eeh_ops::
restore_config() so that we have chance to configure AER correctly
for PowerNV platform.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
The one instance where we add an include for init.h covers off
a case where that file was implicitly getting it from another
header which itself didn't need it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc fix from Ben Herrenschmidt:
"Here's one regression fix for 3.13 that I would appreciate if you
could still pull in. It was an "interesting" one to debug, basically
it's an old bug that got somewhat "exposed" by new code breaking the
boot on PA Semi boards (yes, it does appear that some people are still
using these!)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Check return value of instance-to-package OF call
On PA-Semi firmware, the instance-to-package callback doesn't seem
to be implemented. We didn't check for error, however, thus
subsequently passed the -1 value returned into stdout_node to
thins like prom_getprop etc...
Thus caused the firmware to load values around 0 (physical) internally
as node structures. It somewhat "worked" as long as we had a NULL in the
right place (address 8) at the beginning of the kernel, we didn't "see"
the bug. But commit 5c0484e25e
"powerpc: Endian safe trampoline" changed the kernel entry point causing
that old bug to now cause a crash early during boot.
This fixes booting on PA-Semi board by properly checking the return
value from instance-to-package.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Olof Johansson <olof@lixom.net>
---
the setup before the change was
- arch/powerpc/Kconfig had the PPC_CLOCK option, off by default
- depending on the PPC_CLOCK option the arch/powerpc/kernel/clock.c file
was built, which implements the clk.h API but always returns -ENOSYS
unless a platform registers specific callbacks
- the MPC52xx platform selected PPC_CLOCK but did not register any
callbacks, thus all clk.h API calls keep resulting in -ENOSYS errors
(which is OK, all peripheral drivers deal with the situation)
- the MPC512x platform selected PPC_CLOCK and registered specific
callbacks implemented in arch/powerpc/platforms/512x/clock.c, thus
provided real support for the clock API
- no other powerpc platform did select PPC_CLOCK
the situation after the change is
- the MPC512x platform implements the COMMON_CLK interface, and thus the
PPC_CLOCK approach in arch/powerpc/platforms/512x/clock.c has become
obsolete
- the MPC52xx platform still lacks genuine support for the clk.h API
while this is not a change against the previous situation (the error
code returned from COMMON_CLK stubs differs but every call still
results in an error)
- with all references gone, the arch/powerpc/kernel/clock.c wrapper and
the PPC_CLOCK option have become obsolete, as did the clk_interface.h
header file
the switch from PPC_CLOCK to COMMON_CLK is done for all platforms within
the same commit such that multiplatform kernels (the combination of 512x
and 52xx within one executable) keep working
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
On Freescale e6500 cores EPCR[DGTMI] controls whether guest supervisor
state can execute TLB management instructions. If EPCR[DGTMI]=0
tlbwe and tlbilx are allowed to execute normally in the guest state.
A hypervisor may choose to virtualize TLB1 and for this purpose it
may use IPROT to protect the entries for being invalidated by the
guest. However, because tlbwe and tlbilx execution in the guest state
are sharing the same bit, it is not possible to have a scenario where
tlbwe is allowed to be executed in guest state and tlbilx traps. When
guest TLB management instructions are allowed to be executed in guest
state the guest cannot use tlbilx to invalidate TLB1 guest entries.
Linux is using tlbilx in the boot code to invalidate the temporary
entries it creates when initializing the MMU. The patch is replacing
the usage of tlbilx in initialization code with tlbwe with VALID bit
cleared.
Linux is also using tlbilx in other contexts (like huge pages or
indirect entries) but removing the tlbilx from the initialization code
offers the possibility to have scenarios under hypervisor which are
not using huge pages or indirect entries.
Signed-off-by: Diana Craciun <Diana.Craciun@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
There are a few things that make the existing hw tablewalk handlers
unsuitable for e6500:
- Indirect entries go in TLB1 (though the resulting direct entries go in
TLB0).
- It has threads, but no "tlbsrx." -- so we need a spinlock and
a normal "tlbsx". Because we need this lock, hardware tablewalk
is mandatory on e6500 unless we want to add spinlock+tlbsx to
the normal bolted TLB miss handler.
- TLB1 has no HES (nor next-victim hint) so we need software round robin
(TODO: integrate this round robin data with hugetlb/KVM)
- The existing tablewalk handlers map half of a page table at a time,
because IBM hardware has a fixed 1MiB indirect page size. e6500
has variable size indirect entries, with a minimum of 2MiB.
So we can't do the half-page indirect mapping, and even if we
could it would be less efficient than mapping the full page.
- Like on e5500, the linear mapping is bolted, so we don't need the
overhead of supporting nested tlb misses.
Note that hardware tablewalk does not work in rev1 of e6500.
We do not expect to support e6500 rev1 in mainline Linux.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
When booting above the 64M for a secondary cpu, we also face the
same issue as the boot cpu that the PAGE_OFFSET map two different
physical address for the init tlb and the final map. So we have to use
switch_to_as1/restore_to_as0 between the conversion of these two
maps. When restoring to as0 for a secondary cpu, we only need to
return to the caller. So add a new parameter for function
restore_to_as0 for this purpose.
Use LOAD_REG_ADDR_PIC to get the address of variables which may
be used before we set the final map in cams for the secondary cpu.
Move the setting of cams a bit earlier in order to avoid the
unnecessary using of LOAD_REG_ADDR_PIC.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This is always true for a non-relocatable kernel. Otherwise the kernel
would get stuck. But for a relocatable kernel, it seems a little
complicated. When booting a relocatable kernel, we just align the
kernel start addr to 64M and map the PAGE_OFFSET from there. The
relocation will base on this virtual address. But if this address
is not the same as the memstart_addr, we will have to change the
map of PAGE_OFFSET to the real memstart_addr and do another relocation
again.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
[scottwood@freescale.com: make offset long and non-negative in simple case]
Signed-off-by: Scott Wood <scottwood@freescale.com>
For a relocatable kernel since it can be loaded at any place, there
is no any relation between the kernel start addr and the memstart_addr.
So we can't calculate the memstart_addr from kernel start addr. And
also we can't wait to do the relocation after we get the real
memstart_addr from device tree because it is so late. So introduce
a new function we can use to get the first memblock address and size
in a very early stage (before machine_init).
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
We use the tlb1 entries to map low mem to the kernel space. In the
current code, it assumes that the first tlb entry would cover the
kernel image. But this is not true for some special cases, such as
when we run a relocatable kernel above the 64M or set
CONFIG_KERNEL_START above 64M. So we choose to switch to address
space 1 before setting these tlb entries.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This is based on the codes in the head_44x.S. The difference is that
the init tlb size we used is 64M. With this patch we can only load the
kernel at address between memstart_addr ~ memstart_addr + 64M. We will
fix this restriction in the following patches.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Move the codes which translate a effective address to physical address
to a separate function. So it can be reused by other code.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The e500v1 doesn't implement the MAS7, so we should avoid to access
this register on that implementations. In the current kernel, the
access to MAS7 are protected by either CONFIG_PHYS_64BIT or
MMU_FTR_BIG_PHYS. Since some code are executed before the code
patching, we have to use CONFIG_PHYS_64BIT in these cases.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add a sys interface to enable/diable pw20 state or altivec idle, and
control the wait entry time.
Enable/Disable interface:
0, disable. 1, enable.
/sys/devices/system/cpu/cpuX/pw20_state
/sys/devices/system/cpu/cpuX/altivec_idle
Set wait time interface:(Nanosecond)
/sys/devices/system/cpu/cpuX/pw20_wait_time
/sys/devices/system/cpu/cpuX/altivec_idle_wait_time
Example: Base on TBfreq is 41MHZ.
1~48(ns): TB[63]
49~97(ns): TB[62]
98~195(ns): TB[61]
196~390(ns): TB[60]
391~780(ns): TB[59]
781~1560(ns): TB[58]
...
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
[scottwood@freescale.com: change ifdef]
Signed-off-by: Scott Wood <scottwood@freescale.com>
This modifies kvmppc_load_fp and kvmppc_save_fp to use the generic
FP/VSX and VMX load/store functions instead of open-coding the
FP/VSX/VMX load/store instructions. Since kvmppc_load/save_fp don't
follow C calling conventions, we make them private symbols within
book3s_hv_rmhandlers.S.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This uses struct thread_fp_state and struct thread_vr_state to store
the floating-point, VMX/Altivec and VSX state, rather than flat arrays.
This makes transferring the state to/from the thread_struct simpler
and allows us to unify the get/set_one_reg implementations for the
VSX registers.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
kvm_hypercall() have nothing KVM specific, so renamed to epapr_hypercall().
Also this in moved to arch/powerpc/include/asm/epapr_hcalls.h
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Using hardware features make core automatically enter PW20 state.
Set a TB count to hardware, the effective count begins when PW10
is entered. When the effective period has expired, the core will
proceed from PW10 to PW20 if no exit conditions have occurred during
the period.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Each core's AltiVec unit may be placed into a power savings mode
by turning off power to the unit. Core hardware will automatically
power down the AltiVec unit after no AltiVec instructions have
executed in N cycles. The AltiVec power-control is triggered by hardware.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This fixes a build break that was probably introduced with the removal
of -Wa,-me500 (commit f49596a4cf), where
the assembler refuses to recognize SPRG4-7 with a generic PPC target.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Dongsheng Wang <dongsheng.wang@freescale.com>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Reviewed-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Tested-by: Wang Dongsheng <dongsheng.wang@freescale.com>
The e500 SPE floating-point emulation code clears existing exceptions
(__FPU_FPSCR &= ~FP_EX_MASK;) before ORing in the exceptions from the
emulated operation. However, these exception bits are the "sticky",
cumulative exception bits, and should only be cleared by the user
program setting SPEFSCR, not implicitly by any floating-point
instruction (whether executed purely by the hardware or emulated).
The spurious clearing of these bits shows up as missing exceptions in
glibc testing.
Fixing this, however, is not as simple as just not clearing the bits,
because while the bits may be from previous floating-point operations
(in which case they should not be cleared), the processor can also set
the sticky bits itself before the interrupt for an exception occurs,
and this can happen in cases when IEEE 754 semantics are that the
sticky bit should not be set. Specifically, the "invalid" sticky bit
is set in various cases with non-finite operands, where IEEE 754
semantics do not involve raising such an exception, and the
"underflow" sticky bit is set in cases of exact underflow, whereas
IEEE 754 semantics are that this flag is set only for inexact
underflow. Thus, for correct emulation the kernel needs to know the
setting of these two sticky bits before the instruction being
emulated.
When a floating-point operation raises an exception, the kernel can
note the state of the sticky bits immediately afterwards. Some
<fenv.h> functions that affect the state of these bits, such as
fesetenv and feholdexcept, need to use prctl with PR_GET_FPEXC and
PR_SET_FPEXC anyway, and so it is natural to record the state of those
bits during that call into the kernel and so avoid any need for a
separate call into the kernel to inform it of a change to those bits.
Thus, the interface I chose to use (in this patch and the glibc port)
is that one of those prctl calls must be made after any userspace
change to those sticky bits, other than through a floating-point
operation that traps into the kernel anyway. feclearexcept and
fesetexceptflag duly make those calls, which would not be required
were it not for this issue.
The previous EGLIBC port, and the uClibc code copied from it, is
fundamentally broken as regards any use of prctl for floating-point
exceptions because it didn't use the PR_FP_EXC_SW_ENABLE bit in its
prctl calls (and did various worse things, such as passing a pointer
when prctl expected an integer). If you avoid anything where prctl is
used, the clearing of sticky bits still means it will never give
anything approximating correct exception semantics with existing
kernels. I don't believe the patch makes things any worse for
existing code that doesn't try to inform the kernel of changes to
sticky bits - such code may get incorrect exceptions in some cases,
but it would have done so anyway in other cases.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
LRAT (Logical to Real Address Translation) present in MMU v2 provides hardware
translation from a logical page number (LPN) to a real page number (RPN) when
tlbwe is executed by a guest or when a page table translation occurs from a
guest virtual address.
Add LRAT error exception handler to Booke3E 64-bit kernel and the basic KVM
handler to avoid build breakage. This is a prerequisite for KVM LRAT support
that will follow.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Pull powerpc fixes from Ben Herrenschmidt:
"A bit more endian problems found during testing of 3.13 and a few
other simple fixes and regressions fixes"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix alignment of secondary cpu spin vars
powerpc: Align p_end
powernv/eeh: Add buffer for P7IOC hub error data
powernv/eeh: Fix possible buffer overrun in ioda_eeh_phb_diag()
powerpc: Make 64-bit non-VMX __copy_tofrom_user bi-endian
powerpc: Make unaligned accesses endian-safe for powerpc
powerpc: Fix bad stack check in exception entry
powerpc/512x: dts: disable MPC5125 usb module
powerpc/512x: dts: remove misplaced IRQ spec from 'soc' node (5125)
Merge a pile of fixes that went into the "merge" branch (3.13-rc's) such
as Anton Little Endian fixes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The SLB save area is shared with the hypervisor and is defined
as big endian, so we need to byte swap on little endian builds.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch updates the generic iommu backend code to use the
it_page_shift field to determine the iommu page size instead of
using hardcoded values.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a it_page_shift field to struct iommu_table and
initiliases it to 4K for all platforms.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc iommu uses a hardcoded page size of 4K. This patch changes
the name of the IOMMU_PAGE_* macros to reflect the hardcoded values. A
future patch will use the existing names to support dynamic page
sizes.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With recent machine check patch series changes, The exception vectors
starting from 0x4300 are now overflowing with allyesconfig. Fix that by
moving machine_check_common and machine_check_handle_early code out of
that region to make enough room for exception vector area.
Fixes this build error reportes by Stephen:
arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:958: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:959: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:983: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:984: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1003: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1013: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1014: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1015: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1016: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1017: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1018: Error: attempt to move .org backwards
[Moved the code further down as it introduced link errors due to too long
relative branches to the masked interrupts handlers from the exception
prologs. Also removed the useless feature section --BenH
]
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 5c0484e25e ('powerpc: Endian safe trampoline') resulted in
losing proper alignment of the spinlock variables used when booting
secondary CPUs, causing some quite odd issues with failing to boot on
PA Semi-based systems.
This showed itself on ppc64_defconfig, but not on pasemi_defconfig,
so it had gone unnoticed when I initially tested the LE patch set.
Fix is to add explicit alignment instead of relying on good luck. :)
[ It appears that there is a different issue with PA Semi systems
however this fix is definitely correct so applying anyway -- BenH
]
Fixes: 5c0484e25e ('powerpc: Endian safe trampoline')
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=67811
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
p_end is an 8 byte value embedded in the text section. This means it
is only 4 byte aligned when it should be 8 byte aligned. Fix this
by adding an explicit alignment.
This fixes an issue where POWER7 little endian builds with
CONFIG_RELOCATABLE=y fail to boot.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These interfaces:
pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region)
took a pci_dev, but they really depend only on the pci_bus. And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:
pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region)
In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We don't use PACATOC for PR. Avoid updating HOST_R2 with PR
KVM mode when both HV and PR are enabled in the kernel. Without this we
get the below crash
(qemu)
Unable to handle kernel paging request for data at address 0xffffffffffff8310
Faulting instruction address: 0xc00000000001d5a4
cpu 0x2: Vector: 300 (Data Access) at [c0000001dc53aef0]
pc: c00000000001d5a4: .vtime_delta.isra.1+0x34/0x1d0
lr: c00000000001d760: .vtime_account_system+0x20/0x60
sp: c0000001dc53b170
msr: 8000000000009032
dar: ffffffffffff8310
dsisr: 40000000
current = 0xc0000001d76c62d0
paca = 0xc00000000fef1100 softe: 0 irq_happened: 0x01
pid = 4472, comm = qemu-system-ppc
enter ? for help
[c0000001dc53b200] c00000000001d760 .vtime_account_system+0x20/0x60
[c0000001dc53b290] c00000000008d050 .kvmppc_handle_exit_pr+0x60/0xa50
[c0000001dc53b340] c00000000008f51c kvm_start_lightweight+0xb4/0xc4
[c0000001dc53b510] c00000000008cdf0 .kvmppc_vcpu_run_pr+0x150/0x2e0
[c0000001dc53b9e0] c00000000008341c .kvmppc_vcpu_run+0x2c/0x40
[c0000001dc53ba50] c000000000080af4 .kvm_arch_vcpu_ioctl_run+0x54/0x1b0
[c0000001dc53bae0] c00000000007b4c8 .kvm_vcpu_ioctl+0x478/0x730
[c0000001dc53bca0] c0000000002140cc .do_vfs_ioctl+0x4ac/0x770
[c0000001dc53bd80] c0000000002143e8 .SyS_ioctl+0x58/0xb0
[c0000001dc53be30] c000000000009e58 syscall_exit+0x0/0x98
Signed-off-by: Alexander Graf <agraf@suse.de>
A couple more device tree properties that need byte swapping.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cpu_to_core_id() is missing a byteswap:
cat /sys/devices/system/cpu/cpu63/topology/core_id
201326592
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During on LE boot we see:
Partition configured for 1073741824 cpus, operating system maximum is 2048.
Clearly missing a byteswap here.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is a bug in using ptrace to access FPRs via PTRACE_PEEKUSR /
PTRACE_POKEUSR. In effect, trying to access any of the FPRs always
really accesses FPR0, which does seriously break debugging :-)
The problem seems to have been introduced by commit 3ad26e5c44
(Merge branch 'for-kvm' into next).
[ It is indeed a merge conflict between Paul's FPU/VSX state rework
and my LE patches - Anton ]
Signed-off-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit ce11e48b7f ("KVM: PPC: E500: Add
userspace debug stub support") added "struct thread_struct" to the
stack of kvmppc_vcpu_run(). thread_struct is 1152 bytes on my build,
compared to 48 bytes for the recently-introduced "struct debug_reg".
Use the latter instead.
This fixes the following error:
cc1: warnings being treated as errors
arch/powerpc/kvm/booke.c: In function 'kvmppc_vcpu_run':
arch/powerpc/kvm/booke.c:760:1: error: the frame size of 1424 bytes is larger than 1024 bytes
make[2]: *** [arch/powerpc/kvm/booke.o] Error 1
make[1]: *** [arch/powerpc/kvm] Error 2
make[1]: *** Waiting for unfinished jobs....
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The current logic sets the kdump base to min of 2G or ppc64_rma_size/2.
On PowerNV kernel the first memory block 'memory@0' can be very large,
equal to the DIMM size with ppc64_rma_size value capped to 1G. Hence on
PowerNV, kdump base is set to 512M resulting kdump to fail while allocating
paca array. This is because, paca need its memory from RMA region capped
at 256M (see allocate_pacas()).
This patch lowers the kdump base cap to 128M so that kdump kernel can
successfully get memory below 256M for paca allocation.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
