Make sure to drop any reference taken by bus_find_device() when creating
devices during init and driver registration.
Fixes: 55347cc996 ("[POWERPC] ibmebus: Add device creation and bus probing based on of_device")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make sure to drop any reference taken by bus_find_device() in the sysfs
callbacks that are used to create and destroy devices based on
device-tree entries.
Fixes: 6bccf755ff ("[POWERPC] ibmebus: dynamic addition/removal of adapters, some code cleanup")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This condenses the opal node searching into a single function that finds
all compatible nodes, instead of just searching the ibm,opal children,
for ipmi, flash, and prd similar to how opal-i2c nodes are found.
Signed-off-by: Jack Miller <jack@codezen.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Load monitored is no longer supported on POWER9 so let's remove the
code.
This reverts commit bd3ea317fd ("powerpc: Load Monitor Register
Support").
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As explained by commit 9c0da3cc61 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"), including skeleton.dtsi is deprecated.
This fixes the following warning with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It turns out that the i2c1 adapter is connected to a multiplexer
controlled by a gpio line. The first (default) mux option connects
i2c1 to a bus connected to the already known peripherals. The other
one connects the adapter to the ddc pins of the DVI port.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the schematics of CompuLab's sbc-fx6 baseboard and the
vendor devicetree GPIO_16 is *not* muxed to ENET_REF_CLK but to SPDIF_IN.
Remove the wrong pinctrl setting.
Fixes: 682d055e6a ("ARM: dts: Add initial support for cm-fx6.")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The UART pinmux defines for the pins which are part of the LPSR
pinmux controller are wrong: Output signals configure the input
sel value and the pinmux defines allow not to distinguish between
DCE/DTE mode. Follow the usual pattern using DTE/DCE as part of
the define to denote the two UART configuration options.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6QP the LDB clock tree has changed to move the clk gate
before the divider, to prevent clock glitches propagating downstream.
A consequence of this change is that the clk divider is now the
parent of the LDB inputs. Reflect this change in the devicetree
to allow the LDB driver to properly configure the display clocks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the datasheet, VF610 uses revision r3p2 of the L2C-310
block, same as i.MX6Q+, which does not require a software workaround for
ARM errata 769419.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
MMDC has a slightly different programming model between imx6q and imx6qp
in terms of perf support, it's exactly same for suspend support, so we
have fsl,imx6q-mmdc here to save patching suspend driver with the new
compatible.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6QP added new register bit PROFILE_SEL in MADPCR0.
need set it at perf start.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a compatible entry for the specific board versions.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The board is now manufactured by Aries Embedded GmbH, update compat string.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The board is now manufactured by Aries Embedded GmbH, update compat string.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On some platforms, there is occasional panic triggered when
trying to resume from hibernation, a typical panic looks like:
"BUG: unable to handle kernel paging request at ffff880085894000
IP: [<ffffffff810c5dc2>] load_image_lzo+0x8c2/0xe70"
Investigation carried out by Lee Chun-Yi shows that this is because
e820 map has been changed by BIOS across hibernation, and one
of the page frames from suspend kernel is right located in restore
kernel's unmapped region, so panic comes out when accessing unmapped
kernel address.
In order to expose this issue earlier, the md5 hash of e820 map
is passed from suspend kernel to restore kernel, and the restore
kernel will terminate the resume process once it finds the md5
hash are not the same.
As the format of image header has been modified, the magic number
should also be adjusted as kernels with the same RESTORE_MAGIC have
to use the same header format and interpret all of the fields in
it in the same way.
If the suspend kernel is built without md5 support, and the restore
kernel has md5 support, then the latter will bypass the check process.
Vice versa the restore kernel will bypass the check if it does not
support md5 operation.
Note:
1. Without this patch applied, it is possible that BIOS has
provided an inconsistent memory map, but the resume kernel is still
able to restore the image anyway(e.g, E820_RAM region is the superset
of the previous one), although the system might be unstable. So this
patch tries to treat any inconsistent e820 as illegal.
2. Another case is, this patch replies on comparing the e820_saved, but
currently the e820_save might not be strictly the same across
hibernation, even if BIOS has provided consistent e820 map - In
theory mptable might modify the BIOS-provided e820_saved dynamically
in early_reserve_e820_mpc_new, which would allocate a buffer from
E820_RAM, and marks it from E820_RAM to E820_RESERVED).
This is a potential and rare case we need to deal with in OS in
the future.
Suggested-by: Pavel Machek <pavel@ucw.cz>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No one uses reiserfs much these days, or is likely to in future. So drop
it from pseries and powernv defconfigs to save time and space. It's
still enabled in ppc64_defconfig so we get some build coverage.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In ISA v2.05, the tlbiel instruction takes two arguments, RB and L:
tlbiel RB,L
+---------+---------+----+---------+---------+---------+----+
| 31 | / | L | / | RB | 274 | / |
| 31 - 26 | 25 - 22 | 21 | 20 - 16 | 15 - 11 | 10 - 1 | 0 |
+---------+---------+----+---------+---------+---------+----+
In ISA v2.06 tlbiel takes only one argument, RB:
tlbiel RB
+---------+---------+---------+---------+---------+----+
| 31 | / | / | RB | 274 | / |
| 31 - 26 | 25 - 21 | 20 - 16 | 15 - 11 | 10 - 1 | 0 |
+---------+---------+---------+---------+---------+----+
And in ISA v3.00 tlbiel takes five arguments:
tlbiel RB,RS,RIC,PRS,R
+---------+---------+----+---------+----+----+---------+---------+----+
| 31 | RS | / | RIC |PRS | R | RB | 274 | / |
| 31 - 26 | 25 - 21 | 20 | 19 - 18 | 17 | 16 | 15 - 11 | 10 - 1 | 0 |
+---------+---------+----+---------+----+----+---------+---------+----+
However the assembler also accepts "tlbiel RB", and generates
"tlbiel RB,r0,0,0,0".
As you can see above the L field from the v2.05 encoding overlaps with the
reserved field of the v2.06 encoding, and the low bit of the RS field of the
v3.00 encoding.
Currently in __tlbiel() we generate two tlbiel instructions manually using hex
constants. In the first case, for MMU_PAGE_4K, we generate "tlbiel RB,0", which
is safe in all cases, because the L bit is zero.
However in the default case we generate "tlbiel RB,1", therefore setting bit 21
to 1.
This is not an actual bug on v2.06 processors, because the CPU ignores the value
of the reserved field. However software is supposed to encode the reserved
fields as zero to enable forward compatibility.
On v3.00 processors setting bit 21 to 1 and no other bits of RS, means we are
using r1 for the value of RS.
Although it's not obvious, the code sets the IS field (bits 10-11) to 0 (by
omission), and L=1, in the va value, which is passed as RB. We also pass R=0 in
the instruction.
The combination of IS=0, L=1 and R=0 means the value of RS is not used, so even
on ISA v3.00 there is no actual bug.
We should still fix it, as setting a reserved bit on v2.06 is naughty, and we
are only avoiding a bug on v3.00 by accident rather than design. Use
ASM_FTR_IFSET() to generate the single argument form on ISA v2.06 and later, and
the two argument form on pre v2.06.
Although there may be very old toolchains which don't understand tlbiel, we have
other code in the tree which has been using tlbiel for over five years, and no
one has reported any build failures, so just let the assembler generate the
instructions.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Rewrite change log, use IFSET instead of IFCLR]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we're not compiling for a specific CPU, ie. none of the
CONFIG_POWERx_CPU options are set, and CONFIG_GENERIC_CPU *is* set, we
currently don't pass any -mcpu option to the compiler. This means the
compiler builds for a "generic" Power CPU.
But back in 2014 we dropped support for pre power4 CPUs in commit
468a33028e ("powerpc: Drop support for pre-POWER4 cpus").
Given that, there's no point in building the kernel to run on pre power4
cpus. So update the flags we pass to the compiler when
CONFIG_GENERIC_CPU is set, to specify -mcpu=power4.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a config option that can help exercise the case when
the kernel is not running at PAGE_OFFSET.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
An hcall was recently added that does exactly what we need during kexec
- it clears the entire MMU hash table, ignoring any VRMA mappings.
Try it and fall back to the old method if we get a failure.
On a POWER8 box with 5TB of memory, this reduces the time it takes to
kexec a new kernel from from 4 minutes to 1 minute.
Signed-off-by: Anton Blanchard <anton@samba.org>
Tested-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
[mpe: Split into separate functions and tweak function naming]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This halves the exception table size on 64-bit builds, and it allows
build-time sorting of exception tables to work on relocated kernels.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Minor asm fixups and bits to keep the selftests working]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This macro is taken from s390, and allows more flexibility in
changing exception table format.
mpe: Put it in ppc_asm.h and only define one version using
stringinfy_in_c(). Add some empty definitions and headers to keep the
selftests happy.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We haven't seen these before, but the soon to be merged relative
exception tables support causes them to be generated.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There's no reason to #error if we include ppc_asm.h in asm files, the
ifdef already prevents any problems.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Exception handlers are aligned to 128 bytes (L1 cache) on 64s, which is
overkill. It can reduce the icache footprint of any individual exception
path. However taken as a whole, the expansion in icache footprint seems
likely to be counter-productive and cause more total misses.
Create IFETCH_ALIGN_SHIFT/BYTES, which should give optimal ifetch
alignment with much more reasonable alignment. This saves 1792 bytes
from head_64.o text with an allmodconfig build.
Other subarchitectures should define appropriate IFETCH_ALIGN_SHIFT
values if this becomes more widely used.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are three #ifdef CONFIG_PPC_BOOK3E sections in nohash/64/pgtable.h.
And there should be no configurations possible which use nohash/64/pgtable.h
but don't also enable CONFIG_PPC_BOOK3E.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Rui Teng <rui.teng@linux.vnet.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
wait for next week.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQExBAABCAAbBQJYJvAXFBxwYm9uemluaUByZWRoYXQuY29tAAoJEL/70l94x66D
ztUH/3DZVYkVYUea+Sk1mBnLaK5cbEJMGtxV/NsAqwz8rYB981cB5Iqw0+f2HX2G
LWLc0cf/kyUH+6TrFxQFyXLsBvV7xku2YwJdoiRutpR50767qPFPaPUBHcxCYPYR
MI4VSXb1hW0c4rd8409HesKv5qc5BiYjdWKPMu+f1LUF2CED+Xq4SWHVg+CwSE8i
UInvFUlj/ejQlSdxN2piv87SRcMuO+4nzP+JbtyN7onvtLIah6JfvHhlOO6em+0c
KX1G3qQ6fth6jewTdOPUB1Tx8CoEAZ+YLieRQA19vGHVI4eIhofDgtSaPZJmu9G7
0kjbrlqAuViTEsRl7Dx8zT8OpBM=
=N6w9
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"ARM fixes. There are a couple pending x86 patches but they'll have to
wait for next week"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm/arm64: vgic: Kick VCPUs when queueing already pending IRQs
KVM: arm/arm64: vgic: Prevent access to invalid SPIs
arm/arm64: KVM: Perform local TLB invalidation when multiplexing vcpus on a single CPU
Booting an EFI mixed mode kernel has been crashing since commit:
e37e43a497 ("x86/mm/64: Enable vmapped stacks (CONFIG_HAVE_ARCH_VMAP_STACK=y)")
The user-visible effect in my test setup was the kernel being unable
to find the root file system ramdisk. This was likely caused by silent
memory or page table corruption.
Enabling CONFIG_DEBUG_VIRTUAL=y immediately flagged the thunking code as
abusing virt_to_phys() because it was passing addresses that were not
part of the kernel direct mapping.
Use the slow version instead, which correctly handles all memory
regions by performing a page table walk.
Suggested-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112210424.5157-3-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix this when building on 32-bit:
arch/x86/platform/efi/efi.c: In function ‘__efi_enter_virtual_mode’:
arch/x86/platform/efi/efi.c:911:5: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(efi_memory_desc_t *)pa);
^
arch/x86/platform/efi/efi.c:918:5: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(efi_memory_desc_t *)pa);
^
The @pa local variable is declared as phys_addr_t and that is a u64 when
CONFIG_PHYS_ADDR_T_64BIT=y. (The last is enabled on 32-bit on a PAE
build.)
However, its value comes from __pa() which is basically doing pointer
arithmetic and checking, and returns unsigned long as it is the native
pointer width.
So let's use an unsigned long too. It should be fine to do so because
the later users cast it to a pointer too.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112210424.5157-2-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Apple's EFI drivers supply device properties which are needed to support
Macs optimally. They contain vital information which cannot be obtained
any other way (e.g. Thunderbolt Device ROM). They're also used to convey
the current device state so that OS drivers can pick up where EFI
drivers left (e.g. GPU mode setting).
There's an EFI driver dubbed "AAPL,PathProperties" which implements a
per-device key/value store. Other EFI drivers populate it using a custom
protocol. The macOS bootloader /System/Library/CoreServices/boot.efi
retrieves the properties with the same protocol. The kernel extension
AppleACPIPlatform.kext subsequently merges them into the I/O Kit
registry (see ioreg(8)) where they can be queried by other kernel
extensions and user space.
This commit extends the efistub to retrieve the device properties before
ExitBootServices is called. It assigns them to devices in an fs_initcall
so that they can be queried with the API in <linux/property.h>.
Note that the device properties will only be available if the kernel is
booted with the efistub. Distros should adjust their installers to
always use the efistub on Macs. grub with the "linux" directive will not
work unless the functionality of this commit is duplicated in grub.
(The "linuxefi" directive should work but is not included upstream as of
this writing.)
The custom protocol has GUID 91BD12FE-F6C3-44FB-A5B7-5122AB303AE0 and
looks like this:
typedef struct {
unsigned long version; /* 0x10000 */
efi_status_t (*get) (
IN struct apple_properties_protocol *this,
IN struct efi_dev_path *device,
IN efi_char16_t *property_name,
OUT void *buffer,
IN OUT u32 *buffer_len);
/* EFI_SUCCESS, EFI_NOT_FOUND, EFI_BUFFER_TOO_SMALL */
efi_status_t (*set) (
IN struct apple_properties_protocol *this,
IN struct efi_dev_path *device,
IN efi_char16_t *property_name,
IN void *property_value,
IN u32 property_value_len);
/* allocates copies of property name and value */
/* EFI_SUCCESS, EFI_OUT_OF_RESOURCES */
efi_status_t (*del) (
IN struct apple_properties_protocol *this,
IN struct efi_dev_path *device,
IN efi_char16_t *property_name);
/* EFI_SUCCESS, EFI_NOT_FOUND */
efi_status_t (*get_all) (
IN struct apple_properties_protocol *this,
OUT void *buffer,
IN OUT u32 *buffer_len);
/* EFI_SUCCESS, EFI_BUFFER_TOO_SMALL */
} apple_properties_protocol;
Thanks to Pedro Vilaça for this blog post which was helpful in reverse
engineering Apple's EFI drivers and bootloader:
https://reverse.put.as/2016/06/25/apple-efi-firmware-passwords-and-the-scbo-myth/
If someone at Apple is reading this, please note there's a memory leak
in your implementation of the del() function as the property struct is
freed but the name and value allocations are not.
Neither the macOS bootloader nor Apple's EFI drivers check the protocol
version, but we do to avoid breakage if it's ever changed. It's been the
same since at least OS X 10.6 (2009).
The get_all() function conveniently fills a buffer with all properties
in marshalled form which can be passed to the kernel as a setup_data
payload. The number of device properties is dynamic and can change
between a first invocation of get_all() (to determine the buffer size)
and a second invocation (to retrieve the actual buffer), hence the
peculiar loop which does not finish until the buffer size settles.
The macOS bootloader does the same.
The setup_data payload is later on unmarshalled in an fs_initcall. The
idea is that most buses instantiate devices in "subsys" initcall level
and drivers are usually bound to these devices in "device" initcall
level, so we assign the properties in-between, i.e. in "fs" initcall
level.
This assumes that devices to which properties pertain are instantiated
from a "subsys" initcall or earlier. That should always be the case
since on macOS, AppleACPIPlatformExpert::matchEFIDevicePath() only
supports ACPI and PCI nodes and we've fully scanned those buses during
"subsys" initcall level.
The second assumption is that properties are only needed from a "device"
initcall or later. Seems reasonable to me, but should this ever not work
out, an alternative approach would be to store the property sets e.g. in
a btree early during boot. Then whenever device_add() is called, an EFI
Device Path would have to be constructed for the newly added device,
and looked up in the btree. That way, the property set could be assigned
to the device immediately on instantiation. And this would also work for
devices instantiated in a deferred fashion. It seems like this approach
would be more complicated and require more code. That doesn't seem
justified without a specific use case.
For comparison, the strategy on macOS is to assign properties to objects
in the ACPI namespace (AppleACPIPlatformExpert::mergeEFIProperties()).
That approach is definitely wrong as it fails for devices not present in
the namespace: The NHI EFI driver supplies properties for attached
Thunderbolt devices, yet on Macs with Thunderbolt 1 only one device
level behind the host controller is described in the namespace.
Consequently macOS cannot assign properties for chained devices. With
Thunderbolt 2 they started to describe three device levels behind host
controllers in the namespace but this grossly inflates the SSDT and
still fails if the user daisy-chained more than three devices.
We copy the property names and values from the setup_data payload to
swappable virtual memory and afterwards make the payload available to
the page allocator. This is just for the sake of good housekeeping, it
wouldn't occupy a meaningful amount of physical memory (4444 bytes on my
machine). Only the payload is freed, not the setup_data header since
otherwise we'd break the list linkage and we cannot safely update the
predecessor's ->next link because there's no locking for the list.
The payload is currently not passed on to kexec'ed kernels, same for PCI
ROMs retrieved by setup_efi_pci(). This can be added later if there is
demand by amending setup_efi_state(). The payload can then no longer be
made available to the page allocator of course.
Tested-by: Lukas Wunner <lukas@wunner.de> [MacBookPro9,1]
Tested-by: Pierre Moreau <pierre.morrow@free.fr> [MacBookPro11,3]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pedro Vilaça <reverser@put.as>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: grub-devel@gnu.org
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112213237.8804-9-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We already have a macro to invoke boot services which on x86 adapts
automatically to the bitness of the EFI firmware: efi_call_early().
The macro allows sharing of functions across arches and bitness variants
as long as those functions only call boot services. However in practice
functions in the EFI stub contain a mix of boot services calls and
protocol calls.
Add an efi_call_proto() macro for bitness-agnostic protocol calls to
allow sharing more code across arches as well as deduplicating 32 bit
and 64 bit code paths.
On x86, implement it using a new efi_table_attr() macro for bitness-
agnostic table lookups. Refactor efi_call_early() to make use of the
same macro. (The resulting object code remains identical.)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112213237.8804-8-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While debugging a kernel image size issue, I discovered that if all
non ARCH_QCOM configs in the ARM64 defconfig are disabled, the QCOM
pinctrl drivers will not be built.
The QCOM pinctrl drivers have a dependency on GPIOLIB which was being
selected when other ARCH configs were enabled, but ARCH_QCOM doesn't
select GPIOLIB directly. Let's select GPIOLIB here to ensure the pinctrl
drivers are built for QCOM platforms.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Initial device tree support for Qualcomm MSM8994 SoC and
Huawei Angler / Google Nexus 6P support.
The device tree is based on the Google 3.10 kernel tree.
The device can be booted into the initrd with only one CPU running.
Signed-off-by: Bastian Köcher <mail@kchr.de>
[jeremymc@redhat.com: removed Kconfig, defconfig, move from Huawei to qcom dir]
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Tested-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Initial device tree support for Qualcomm MSM8992 SoC and
LG Bullhead / Google Nexus 5X support.
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch add support to Analog audio both Playback and Capture via
msm8916 WCD muti codec.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Given the mimimal hardware support for msm899(2/4) currently.
A few config options are needed to allow for continued
development and booting.
The following are needed for continued development and
booting:
-8994 pinctrl for serial support
-Enable Global Glock Controller (gcc)
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Since the KERN_CONT changes, the current code in show_instructions()
prints out a whole bunch of unnecessary newlines. Change occurrences of
printk("\n") to pr_cont("\n"). While we're here, change all the other
cases of printk(KERN_CONT ...) to pr_cont() as well.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix up our oops output by converting continuation lines to use
pr_cont(). Some of these are dubious, eg. printing a continuation line
which starts with a newline, but seem to work OK for now. This whole
function needs a rewrite in the next release.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since the KERN_CONT changes these are being horribly split across lines,
for example:
MSR: 8000000000009033 <
SF,EE
,ME,IR
,DR,RI
,LE>
So fix it by using pr_cont() where appropriate.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Previously we got away with printing the stack trace in multiple pieces
and it usually looked right. But since commit 4bcc595ccd ("printk:
reinstate KERN_CONT for printing continuation lines"), KERN_CONT is now
required when printing continuation lines. Use pr_cont() as appropriate.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The changes to use gas sections for constructing the exception vectors
causes a build break when using binutils 2.23:
arch/powerpc/kernel/exceptions-64s.S:770: Error: operand out of range
(0xffffffffffff8100 is not between 0x0000000000000000 and 0x000000000000ffff)
And so on.
Reported by Hugh with binutils-2.23.2-8.1.4.ppc64 from openSUSE 13.1 and
also Naveen & Denis using 2.23.52.0.1-26.el7 from RHEL 7. Strangely
binutils 2.22 (what I test with) is not affected.
This is caused by the use of @l in LOAD_HANDLER(). The @l was only
recently added in commit a24553dd02 ("powerpc/pseries: Remove
unnecessary syscall trampoline").
Luckily the gas section changes split out the LOAD_SYSCALL_HANDLER()
macro, which means we actually *don't* need to use @l in LOAD_HANDLER()
any more, only in LOAD_SYSCALL_HANDLER().
So drop the @l from LOAD_HANDLER().
Fixes: 57f266497d ("powerpc: Use gas sections for arranging exception vectors")
Signed-off-by: Hugh Dickins <hughd@google.com>
[mpe: Add gory details to change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
