The PHY reset signal is controlled by bit PHYRSTZ in the MC_PHYRSTZ
register. The signal is active low on Gen1 PHYs and active high on Gen2
PHYs. The driver toggles the signal high then low, which is correct for
all currently supported platforms, but the register values macros are
incorrectly named. Replace them with a single macro named after the bit,
and add a comment to the source code to explain the behaviour.
The driver's behaviour isn't changed by this rename, the code will still
need to be fixed to support Gen1 PHYs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-19-laurent.pinchart+renesas@ideasonboard.com
Replace the hardcoded register address numerical values with macros to
clarify the code.
This change has been tested by comparing the assembly code before and
after the change.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-18-laurent.pinchart+renesas@ideasonboard.com
Bit 0 in CONFIG1_ID tells whether the IP core uses an AHB slave
interface for control. The correct way to identify AHB audio DMA support
is through bit 1 in CONFIG3_ID.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-15-laurent.pinchart+renesas@ideasonboard.com
The DWC HDMI TX can be recognized by the two product identification
registers. If the registers don't read as expect the IP will be very
different than what the driver has been designed for, or will be
misconfigured in a way that makes it non-operational (invalid memory
address, incorrect clocks, ...). We should reject this situation with an
error.
While this isn't critical for proper operation with supported IPs at the
moment, the driver will soon gain automatic device-specific handling
based on runtime device identification. This change makes it easier to
implement that without having to default to a random guess in case the
device can't be identified.
While at it print a readable version number in the device identification
message instead of raw register values.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-14-laurent.pinchart+renesas@ideasonboard.com
The bit is documented in a Rockchip BSP as
#define m_SVSRET_SIG (1 << 5) /* depend on PHY_MHL_COMB0=1 */
This is confirmed by a Renesas platform, which uses a 2.0 DWC HDMI TX as
the RK3288. Rename the bit accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-13-laurent.pinchart+renesas@ideasonboard.com
Current dw-hdmi is supporting sound via AHB bus, but it has
I2S audio feature too. This patch adds I2S audio support to dw-hdmi.
This HDMI I2S is supported by using ALSA SoC common HDMI encoder
driver.
Tested-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/8737j2bxba.wl%kuninori.morimoto.gx@renesas.com
The change adds support of internal HDMI I2C master controller, this
subdevice is used by default, if "ddc-i2c-bus" DT property is omitted.
The main purpose of this functionality is to support reading EDID from
an HDMI monitor on boards, which don't have an I2C bus connected to
DDC pins.
The current implementation does not support "I2C Master Interface
Extended Read Mode" to read data addressed by non-zero segment
pointer, this means that if EDID has more than 1 extension blocks,
EDID reading operation won't succeed, in my practice all tested HDMI
monitors have at maximum one extension block.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
