The older SoCs like Armada XP support a 2500BaseX mode in the datasheets
referred to as DR-SGMII (Double rated SGMII) or HS-SGMII (High Speed
SGMII). This is an upclocked 1000BaseX mode, thus
PHY_INTERFACE_MODE_2500BASEX is the appropriate mode define for it.
adding support for it merely means writing the correct magic value into
the MVNETA_SERDES_CFG register.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MVNETA_SERDES_CFG register is only available on older SoCs like the
Armada XP. On newer SoCs like the Armada 38x the fields are moved to
comphy. This patch moves the writes to this register next to the comphy
initialization, so that depending on the SoC either comphy or
MVNETA_SERDES_CFG is configured.
With this we no longer write to the MVNETA_SERDES_CFG on SoCs where it
doesn't exist.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per walk_page_range documentation, mmap lock should be acquired by the
caller before invoking walk_page_range. mmap_assert_locked gets triggered
without that. The details can be found here.
http://lists.infradead.org/pipermail/linux-riscv/2020-June/010335.html
Fixes: 395a21ff859c(riscv: add ARCH_HAS_SET_DIRECT_MAP support)
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Michel Lespinasse <walken@google.com>
Reviewed-by: Zong Li <zong.li@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
As per the table 4.4 of version "20190608-Priv-MSU-Ratified" of the
RISC-V instruction set manual[0], the PTE permission bit combination of
"write+exec only" is reserved for future use. Hence, don't allow such
mapping request in mmap call.
An issue is been reported by David Abdurachmanov, that while running
stress-ng with "sysbadaddr" argument, RCU stalls are observed on RISC-V
specific kernel.
This issue arises when the stress-sysbadaddr request for pages with
"write+exec only" permission bits and then passes the address obtain
from this mmap call to various system call. For the riscv kernel, the
mmap call should fail for this particular combination of permission bits
since it's not valid.
[0]: http://dabbelt.com/~palmer/keep/riscv-isa-manual/riscv-privileged-20190608-1.pdf
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reported-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
[Palmer: Refer to the latest ISA specification at the only link I could
find, and update the terminology.]
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
- Fix for timeslicing and virtual engines/unpremptable requests
(+ 1 dependency patch)
- Fixes into TypeC register programming and interrupt storm detecting
- Disable DIP on MST ports with the transcoder clock still on
- Avoid missing GT workarounds at reset for HSW and older gens
- Fix for unwinding multiple requests missing force restore
- Fix encoder type check for DDI vswing sequence
- Build warning fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200618124659.GA12342@jlahtine-desk.ger.corp.intel.com
The cache_idx is currently picked by RR. There is chance that
the same cache_idx will be picked by multiple sk_storage_maps while
other cache_idx is still unused. e.g. It could happen when the
sk_storage_map is recreated during the restart of the user
space process.
This patch tracks the usage count for each cache_idx. There is
16 of them now (defined in BPF_SK_STORAGE_CACHE_SIZE).
It will try to pick the free cache_idx. If none was found,
it would pick one with the minimal usage count.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200617174226.2301909-1-kafai@fb.com
On HS cores, loop buffer (LPB) is programmable in runtime and can
be optionally disabled.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Merge non-faulting memory access cleanups from Christoph Hellwig:
"Andrew and I decided to drop the patches implementing your suggested
rename of the probe_kernel_* and probe_user_* helpers from -mm as
there were way to many conflicts.
After -rc1 might be a good time for this as all the conflicts are
resolved now"
This also adds a type safety checking patch on top of the renaming
series to make the subtle behavioral difference between 'get_user()' and
'get_kernel_nofault()' less potentially dangerous and surprising.
* emailed patches from Christoph Hellwig <hch@lst.de>:
maccess: make get_kernel_nofault() check for minimal type compatibility
maccess: rename probe_kernel_address to get_kernel_nofault
maccess: rename probe_user_{read,write} to copy_{from,to}_user_nofault
maccess: rename probe_kernel_{read,write} to copy_{from,to}_kernel_nofault
Now that we've renamed probe_kernel_address() to get_kernel_nofault()
and made it look and behave more in line with get_user(), some of the
subtle type behavior differences end up being more obvious and possibly
dangerous.
When you do
get_user(val, user_ptr);
the type of the access comes from the "user_ptr" part, and the above
basically acts as
val = *user_ptr;
by design (except, of course, for the fact that the actual dereference
is done with a user access).
Note how in the above case, the type of the end result comes from the
pointer argument, and then the value is cast to the type of 'val' as
part of the assignment.
So the type of the pointer is ultimately the more important type both
for the access itself.
But 'get_kernel_nofault()' may now _look_ similar, but it behaves very
differently. When you do
get_kernel_nofault(val, kernel_ptr);
it behaves like
val = *(typeof(val) *)kernel_ptr;
except, of course, for the fact that the actual dereference is done with
exception handling so that a faulting access is suppressed and returned
as the error code.
But note how different the casting behavior of the two superficially
similar accesses are: one does the actual access in the size of the type
the pointer points to, while the other does the access in the size of
the target, and ignores the pointer type entirely.
Actually changing get_kernel_nofault() to act like get_user() is almost
certainly the right thing to do eventually, but in the meantime this
patch adds logit to at least verify that the pointer type is compatible
with the type of the result.
In many cases, this involves just casting the pointer to 'void *' to
make it obvious that the type of the pointer is not the important part.
It's not how 'get_user()' acts, but at least the behavioral difference
is now obvious and explicit.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ID 1 is already used by the IOVA range capability, use ID 2.
Reported-by: Liu Yi L <yi.l.liu@intel.com>
Fixes: ad721705d0 ("vfio iommu: Add migration capability to report supported features")
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Commit:
da92110dfd ("EDAC, amd64_edac: Extend scrub rate support to F15hM60h")
added support for F15h, model 0x60 CPUs but in doing so, missed to read
back SCRCTRL PCI config register on F15h CPUs which are *not* model
0x60. Add that read so that doing
$ cat /sys/devices/system/edac/mc/mc0/sdram_scrub_rate
can show the previously set DRAM scrub rate.
Fixes: da92110dfd ("EDAC, amd64_edac: Extend scrub rate support to F15hM60h")
Reported-by: Anders Andersson <pipatron@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> #v4.4..
Link: https://lkml.kernel.org/r/CAKkunMbNWppx_i6xSdDHLseA2QQmGJqj_crY=NF-GZML5np4Vw@mail.gmail.com
create_flags checks was refactored and broke the creation on integrity
enabled QPs and actually broke the NVMe/RDMA and iSER ULP's when using
mlx5 driven devices.
Fixes: 2978975ce7 ("RDMA/mlx5: Process create QP flags in one place")
Link: https://lore.kernel.org/r/20200617130230.2846915-1-leon@kernel.org
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Better describe what this helper does, and match the naming of
copy_from_kernel_nofault.
Also switch the argument order around, so that it acts and looks
like get_user().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Like any other QP type, rely on FW for the RAW_PACKET QPs to decide if ECE
is supported or not. This fixes an inability to create RAW_PACKET QPs with
latest rdma-core with the ECE support.
Fixes: e383085c24 ("RDMA/mlx5: Set ECE options during QP create")
Link: https://lore.kernel.org/r/20200618112507.3453496-2-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Remote gid is not copied to the right address. Fix it by using
rdma_ah_set_dgid_raw to copy the remote gid value from the QP context on
query QP.
Fixes: 70bd7fb876 ("RDMA/mlx5: Remove manually crafted QP context the query call")
Link: https://lore.kernel.org/r/20200618112507.3453496-3-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
destroy_qp_common is called for flows where QP is already created by
HW. While it is called from IB/core, the ibqp.* fields will be fully
initialized, but it is not the case if this function is called during QP
creation.
Don't rely on ibqp fields as much as possible and initialize
send_cq/recv_cq as temporal solution till all drivers will be converted to
IB/core QP allocation scheme.
refcount_t: underflow; use-after-free.
WARNING: CPU: 1 PID: 5372 at lib/refcount.c:28 refcount_warn_saturate+0xfe/0x1a0
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 5372 Comm: syz-executor.2 Not tainted 5.5.0-rc5 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Call Trace:
mlx5_core_put_rsc+0x70/0x80
destroy_resource_common+0x8e/0xb0
mlx5_core_destroy_qp+0xaf/0x1d0
mlx5_ib_destroy_qp+0xeb0/0x1460
ib_destroy_qp_user+0x2d5/0x7d0
create_qp+0xed3/0x2130
ib_uverbs_create_qp+0x13e/0x190
? ib_uverbs_ex_create_qp
ib_uverbs_write+0xaa5/0xdf0
__vfs_write+0x7c/0x100
ksys_write+0xc8/0x200
do_syscall_64+0x9c/0x390
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 08d5397660 ("RDMA/mlx5: Copy response to the user in one place")
Link: https://lore.kernel.org/r/20200617130148.2846643-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Currently, address spaces in warnings are displayed as '<asn:X>' with
'X' being the address space's arbitrary number.
But since sparse v0.6.0-rc1 (late December 2018), sparse allows you to
define the address spaces using an identifier instead of a number. This
identifier is then directly used in the warnings.
So, use the identifiers '__user', '__iomem', '__percpu' & '__rcu' for
the corresponding address spaces. The default address space, __kernel,
being not displayed in warnings, stays defined as '0'.
With this change, warnings that used to be displayed as:
cast removes address space '<asn:1>' of expression
... void [noderef] <asn:2> *
will now be displayed as:
cast removes address space '__user' of expression
... void [noderef] __iomem *
This also moves the __kernel annotation to be the first one, since it is
quite different from the others because it's the default one, and so:
- it's never displayed
- it's normally not needed, nor in type annotations, nor in cast
between address spaces. The only time it's needed is when it's
combined with a typeof to express "the same type as this one but
without the address space"
- it can't be defined with a name, '0' must be used.
So, it seemed strange to me to have it in the middle of the other
ones.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If an spi device is unbounded from the driver before the release
process, there will be an NULL pointer reference when it's
referenced in spi_slave_abort().
Fix it by checking it's already freed before reference.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Link: https://lore.kernel.org/r/20200618032125.4650-2-zhenzhong.duan@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are some new broken doc links due to yaml renames
at DT. Developers should really run:
./scripts/documentation-file-ref-check
in order to solve those issues while submitting patches.
This tool can even fix most of the issues with:
./scripts/documentation-file-ref-check --fix
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/0e4a7f0b7efcc8109c8a41a2e13c8adde4d9c6b9.1592203542.git.mchehab+huawei@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Calling pm_runtime_get_sync increments the counter even in case of
failure, causing incorrect ref count if pm_runtime_put is not called in
error handling paths. Call pm_runtime_put if pm_runtime_get_sync fails.
Fixes: fc05a5b222 ("ASoC: rockchip: add support for pdm controller")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200613205158.27296-1-wu000273@umn.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
Since many compilers cannot disable KCOV with a function attribute,
help it to NOP out any __sanitizer_cov_*() calls injected in noinstr
code.
This turns:
12: e8 00 00 00 00 callq 17 <lockdep_hardirqs_on+0x17>
13: R_X86_64_PLT32 __sanitizer_cov_trace_pc-0x4
into:
12: 0f 1f 44 00 00 nopl 0x0(%rax,%rax,1)
13: R_X86_64_NONE __sanitizer_cov_trace_pc-0x4
Just like recordmcount does.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
This provides infrastructure to rewrite instructions; this is
immediately useful for helping out with KCOV-vs-noinstr, but will
also come in handy for a bunch of variable sized jump-label patches
that are still on ice.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
With there being multiple ways to change the ELF data, let's more
concisely track modification.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
kill_bdev does not have any external user, so make it static.
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When a filesystem is mounted on a loop device and on a loop ioctl
LOOP_SET_STATUS64, because of kill_bdev, buffer_head mappings are getting
destroyed.
kill_bdev
truncate_inode_pages
truncate_inode_pages_range
do_invalidatepage
block_invalidatepage
discard_buffer -->clear BH_Mapped flag
sb_bread
__bread_gfp
bh = __getblk_gfp
-->discard_buffer clear BH_Mapped flag
__bread_slow
submit_bh
submit_bh_wbc
BUG_ON(!buffer_mapped(bh)) --> hit this BUG_ON
Fixes: 5db470e229 ("loop: drop caches if offset or block_size are changed")
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 130f4caf14 ("libata: Ensure ata_port probe has completed before
detach") may cause system freeze during suspend.
Using async_synchronize_full() in PM callbacks is wrong, since async
callbacks that are already scheduled may wait for not-yet-scheduled
callbacks, causes a circular dependency.
Instead of using big hammer like async_synchronize_full(), use async
cookie to make sure port probe are synced, without affecting other
scheduled PM callbacks.
Fixes: 130f4caf14 ("libata: Ensure ata_port probe has completed before detach")
Suggested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: John Garry <john.garry@huawei.com>
BugLink: https://bugs.launchpad.net/bugs/1867983
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is a specific API to treat raw data as UUID, i.e. import_uuid().
Use it instead of uuid_copy() with explicit casting.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
LDO1 and LDO2 settings are wrong and case the voltage to go above the
maximum level of 2.15V permitted by the SoC to 3.0V.
This patch is based on work done on the i.MX8M Mini-EVK which utilizes
the same fix.
Fixes: 593816fa2f ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In io_read() or io_write(), when io request is submitted successfully,
it'll go through the below sequence:
kfree(iovec);
req->flags &= ~REQ_F_NEED_CLEANUP;
return ret;
But clearing REQ_F_NEED_CLEANUP might be unsafe. The io request may
already have been completed, and then io_complete_rw_iopoll()
and io_complete_rw() will be called, both of which will also modify
req->flags if needed. This causes a race condition, with concurrent
non-atomic modification of req->flags.
To eliminate this race, in io_read() or io_write(), if io request is
submitted successfully, we don't remove REQ_F_NEED_CLEANUP flag. If
REQ_F_NEED_CLEANUP is set, we'll leave __io_req_aux_free() to the
iovec cleanup work correspondingly.
Cc: stable@vger.kernel.org
Signed-off-by: Xiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If a IMP reset caused by some hardware errors and hns RoCE driver reset
occurred at the same time, there is a possiblity that the IMP will stop
dealing with command and users can't use the hardware. The logs are as
follows:
hns3 0000:fd:00.1: cleaned 0, need to clean 1
hns3 0000:fd:00.1: firmware version query failed -11
hns3 0000:fd:00.1: Cmd queue init failed
hns3 0000:fd:00.1: Upgrade reset level
hns3 0000:fd:00.1: global reset interrupt
The hns NIC driver divides the reset process into 3 status:
initialization, hardware resetting and softwaring restting. RoCE driver
gets reset status by interfaces provided by NIC driver and commands will
not be sent to the IMP if the driver is in any above status. The main
reason for this issue is that there is a time gap between status 1 and 2,
if the RoCE driver sends commands to the IMP during this gap, the IMP will
stop working because it is not ready.
To eliminate the time gap, the hns NIC driver has added a new interface in
commit a4de02287a ("net: hns3: provide .get_cmdq_stat interface for the
client"), so RoCE driver can ensure that no commands will be sent during
resetting.
Link: https://lore.kernel.org/r/1592314778-52822-1-git-send-email-liweihang@huawei.com
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
ibmr.device is assigned after MR is successfully registered, but both
write_mtpt() and frmr_write_mtpt() accesses it during the mr registration
process, which may cause the following error when trying to register MR in
userspace and pbl_hop_num is set to 0.
pc : hns_roce_mtr_find+0xa0/0x200 [hns_roce]
lr : set_mtpt_pbl+0x54/0x118 [hns_roce_hw_v2]
sp : ffff00023e73ba20
x29: ffff00023e73ba20 x28: ffff00023e73bad8
x27: 0000000000000000 x26: 0000000000000000
x25: 0000000000000002 x24: 0000000000000000
x23: ffff00023e73bad0 x22: 0000000000000000
x21: ffff0000094d9000 x20: 0000000000000000
x19: ffff8020a6bdb2c0 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0140000000000000 x12: 0040000000000041
x11: ffff000240000000 x10: 0000000000001000
x9 : 0000000000000000 x8 : ffff802fb7558480
x7 : ffff802fb7558480 x6 : 000000000003483d
x5 : ffff00023e73bad0 x4 : 0000000000000002
x3 : ffff00023e73bad8 x2 : 0000000000000000
x1 : 0000000000000000 x0 : ffff0000094d9708
Call trace:
hns_roce_mtr_find+0xa0/0x200 [hns_roce]
set_mtpt_pbl+0x54/0x118 [hns_roce_hw_v2]
hns_roce_v2_write_mtpt+0x14c/0x168 [hns_roce_hw_v2]
hns_roce_mr_enable+0x6c/0x148 [hns_roce]
hns_roce_reg_user_mr+0xd8/0x130 [hns_roce]
ib_uverbs_reg_mr+0x14c/0x2e0 [ib_uverbs]
ib_uverbs_write+0x27c/0x3e8 [ib_uverbs]
__vfs_write+0x60/0x190
vfs_write+0xac/0x1c0
ksys_write+0x6c/0xd8
__arm64_sys_write+0x24/0x30
el0_svc_common+0x78/0x130
el0_svc_handler+0x38/0x78
el0_svc+0x8/0xc
Solve above issue by adding a pointer of structure hns_roce_dev as a
parameter of write_mtpt() and frmr_write_mtpt(), so that both of these
functions can access it before finishing MR's registration.
Fixes: 9b2cf76c9f ("RDMA/hns: Optimize PBL buffer allocation process")
Link: https://lore.kernel.org/r/1592314629-51715-1-git-send-email-liweihang@huawei.com
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When build perf with ASan or UBSan, if libasan or libubsan can not find,
the feature-glibc is 0 and there exists the following error log which is
wrong, because we can find gnu/libc-version.h in /usr/include,
glibc-devel is also installed.
[yangtiezhu@linux perf]$ make DEBUG=1 EXTRA_CFLAGS='-fno-omit-frame-pointer -fsanitize=address'
BUILD: Doing 'make -j4' parallel build
HOSTCC fixdep.o
HOSTLD fixdep-in.o
LINK fixdep
<stdin>:1:0: warning: -fsanitize=address and -fsanitize=kernel-address are not supported for this target
<stdin>:1:0: warning: -fsanitize=address not supported for this target
Auto-detecting system features:
... dwarf: [ OFF ]
... dwarf_getlocations: [ OFF ]
... glibc: [ OFF ]
... gtk2: [ OFF ]
... libaudit: [ OFF ]
... libbfd: [ OFF ]
... libcap: [ OFF ]
... libelf: [ OFF ]
... libnuma: [ OFF ]
... numa_num_possible_cpus: [ OFF ]
... libperl: [ OFF ]
... libpython: [ OFF ]
... libcrypto: [ OFF ]
... libunwind: [ OFF ]
... libdw-dwarf-unwind: [ OFF ]
... zlib: [ OFF ]
... lzma: [ OFF ]
... get_cpuid: [ OFF ]
... bpf: [ OFF ]
... libaio: [ OFF ]
... libzstd: [ OFF ]
... disassembler-four-args: [ OFF ]
Makefile.config:393: *** No gnu/libc-version.h found, please install glibc-dev[el]. Stop.
Makefile.perf:224: recipe for target 'sub-make' failed
make[1]: *** [sub-make] Error 2
Makefile:69: recipe for target 'all' failed
make: *** [all] Error 2
[yangtiezhu@linux perf]$ ls /usr/include/gnu/libc-version.h
/usr/include/gnu/libc-version.h
After install libasan and libubsan, the feature-glibc is 1 and the build
process is success, so the cause is related with libasan or libubsan, we
should check them and print an error log to reflect the reality.
Committer testing:
$ rm -rf /tmp/build/perf ; mkdir -p /tmp/build/perf
$ make DEBUG=1 EXTRA_CFLAGS='-fno-omit-frame-pointer -fsanitize=address' O=/tmp/build/perf -C tools/perf/ install-bin
make: Entering directory '/home/acme/git/perf/tools/perf'
BUILD: Doing 'make -j12' parallel build
HOSTCC /tmp/build/perf/fixdep.o
HOSTLD /tmp/build/perf/fixdep-in.o
LINK /tmp/build/perf/fixdep
Auto-detecting system features:
... dwarf: [ OFF ]
... dwarf_getlocations: [ OFF ]
... glibc: [ OFF ]
... gtk2: [ OFF ]
... libbfd: [ OFF ]
... libcap: [ OFF ]
... libelf: [ OFF ]
... libnuma: [ OFF ]
... numa_num_possible_cpus: [ OFF ]
... libperl: [ OFF ]
... libpython: [ OFF ]
... libcrypto: [ OFF ]
... libunwind: [ OFF ]
... libdw-dwarf-unwind: [ OFF ]
... zlib: [ OFF ]
... lzma: [ OFF ]
... get_cpuid: [ OFF ]
... bpf: [ OFF ]
... libaio: [ OFF ]
... libzstd: [ OFF ]
... disassembler-four-args: [ OFF ]
Makefile.config:401: *** No libasan found, please install libasan. Stop.
make[1]: *** [Makefile.perf:231: sub-make] Error 2
make: *** [Makefile:70: all] Error 2
make: Leaving directory '/home/acme/git/perf/tools/perf'
$
$
$ sudo dnf install libasan
<SNIP>
Installed:
libasan-9.3.1-2.fc31.x86_64
$
$
$ make DEBUG=1 EXTRA_CFLAGS='-fno-omit-frame-pointer -fsanitize=address' O=/tmp/build/perf -C tools/perf/ install-bin
make: Entering directory '/home/acme/git/perf/tools/perf'
BUILD: Doing 'make -j12' parallel build
Auto-detecting system features:
... dwarf: [ on ]
... dwarf_getlocations: [ on ]
... glibc: [ on ]
... gtk2: [ on ]
... libbfd: [ on ]
... libcap: [ on ]
... libelf: [ on ]
... libnuma: [ on ]
... numa_num_possible_cpus: [ on ]
... libperl: [ on ]
... libpython: [ on ]
... libcrypto: [ on ]
... libunwind: [ on ]
... libdw-dwarf-unwind: [ on ]
... zlib: [ on ]
... lzma: [ on ]
... get_cpuid: [ on ]
... bpf: [ on ]
... libaio: [ on ]
... libzstd: [ on ]
... disassembler-four-args: [ on ]
<SNIP>
CC /tmp/build/perf/util/pmu-flex.o
FLEX /tmp/build/perf/util/expr-flex.c
CC /tmp/build/perf/util/expr-bison.o
CC /tmp/build/perf/util/expr.o
CC /tmp/build/perf/util/expr-flex.o
CC /tmp/build/perf/util/parse-events-flex.o
CC /tmp/build/perf/util/parse-events.o
LD /tmp/build/perf/util/intel-pt-decoder/perf-in.o
LD /tmp/build/perf/util/perf-in.o
LD /tmp/build/perf/perf-in.o
LINK /tmp/build/perf/perf
<SNIP>
INSTALL python-scripts
INSTALL perf_completion-script
INSTALL perf-tip
make: Leaving directory '/home/acme/git/perf/tools/perf'
$ ldd ~/bin/perf | grep asan
libasan.so.5 => /lib64/libasan.so.5 (0x00007f0904164000)
$
And if we rebuild without -fsanitize-address:
$ rm -rf /tmp/build/perf ; mkdir -p /tmp/build/perf
$ make O=/tmp/build/perf -C tools/perf/ install-bin
make: Entering directory '/home/acme/git/perf/tools/perf'
BUILD: Doing 'make -j12' parallel build
HOSTCC /tmp/build/perf/fixdep.o
HOSTLD /tmp/build/perf/fixdep-in.o
LINK /tmp/build/perf/fixdep
Auto-detecting system features:
... dwarf: [ on ]
... dwarf_getlocations: [ on ]
... glibc: [ on ]
... gtk2: [ on ]
... libbfd: [ on ]
... libcap: [ on ]
... libelf: [ on ]
... libnuma: [ on ]
... numa_num_possible_cpus: [ on ]
... libperl: [ on ]
... libpython: [ on ]
... libcrypto: [ on ]
... libunwind: [ on ]
... libdw-dwarf-unwind: [ on ]
... zlib: [ on ]
... lzma: [ on ]
... get_cpuid: [ on ]
... bpf: [ on ]
... libaio: [ on ]
... libzstd: [ on ]
... disassembler-four-args: [ on ]
GEN /tmp/build/perf/common-cmds.h
CC /tmp/build/perf/exec-cmd.o
<SNIP>
INSTALL perf_completion-script
INSTALL perf-tip
make: Leaving directory '/home/acme/git/perf/tools/perf'
$ ldd ~/bin/perf | grep asan
$
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: tiezhu yang <yangtiezhu@loongson.cn>
Cc: xuefeng li <lixuefeng@loongson.cn>
Link: http://lore.kernel.org/lkml/1592445961-28044-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In order to move pointer checks like IS_ERR_VALUE() out of the hotpath
and into the reader path of a trace event, user space tools need to be
able to parse that. IS_ERR_VALUE() is defined as:
#define IS_ERR_VALUE() unlikely((unsigned long)(void *)(x) >= (unsigned long)-MAX_ERRNO)
Which eventually turns into:
__builtin_expect(!!((unsigned long)(void *)(x) >= (unsigned long)-4095), 0)
Now the traceevent parser can handle most of that except for the
__builtin_expect(), which needs to be added.
Link: https://lore.kernel.org/linux-mm/20200320055823.27089-3-jaewon31.kim@samsung.com/
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jaewon Kim <jaewon31.kim@samsung.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kees Kook <keescook@chromium.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: linux-mm@kvack.org
Cc: linux-trace-devel@vger.kernel.org
Link: http://lore.kernel.org/lkml/20200324200956.821799393@goodmis.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Commit c61f13eaa1 ("gcc-plugins: Add structleak for more stack
initialization") added "__attribute__((user))" to the user when
stackleak detector is enabled. This now appears in the field format of
system call trace events for system calls that have user buffers. The
"__attribute__((user))" breaks the parsing in libtraceevent. That needs
to be handled.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jaewon Kim <jaewon31.kim@samsung.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kees Kook <keescook@chromium.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: linux-mm@kvack.org
Cc: linux-trace-devel@vger.kernel.org
Link: http://lore.kernel.org/lkml/20200324200956.663647256@goodmis.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
There's several locations that open code realloc and strcat() to append
text to strings. Add an append() function that takes a delimiter and a
string to append to another string.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jaewon Lim <jaewon31.kim@samsung.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kees Kook <keescook@chromium.org>
Cc: linux-mm@kvack.org
Cc: linux-trace-devel@vger.kernel.org
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Link: http://lore.kernel.org/lkml/20200324200956.515118403@goodmis.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Missed steps during ECE handshake left userspace application with less
options for the ECE handshake. Pass ECE options in the additional
transitions.
Fixes: 50aec2c313 ("RDMA/mlx5: Return ECE data after modify QP")
Link: https://lore.kernel.org/r/20200616104536.2426384-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Private data passed to iwarp_cm_handler is copied for connection request /
response, but ignored otherwise. If junk is passed, it is stored in the
event and used later in the event processing.
The driver passes an old junk pointer during connection close which leads
to a use-after-free on event processing. Set private data to NULL for
events that don 't have private data.
BUG: KASAN: use-after-free in ucma_event_handler+0x532/0x560 [rdma_ucm]
kernel: Read of size 4 at addr ffff8886caa71200 by task kworker/u128:1/5250
kernel:
kernel: Workqueue: iw_cm_wq cm_work_handler [iw_cm]
kernel: Call Trace:
kernel: dump_stack+0x8c/0xc0
kernel: print_address_description.constprop.0+0x1b/0x210
kernel: ? ucma_event_handler+0x532/0x560 [rdma_ucm]
kernel: ? ucma_event_handler+0x532/0x560 [rdma_ucm]
kernel: __kasan_report.cold+0x1a/0x33
kernel: ? ucma_event_handler+0x532/0x560 [rdma_ucm]
kernel: kasan_report+0xe/0x20
kernel: check_memory_region+0x130/0x1a0
kernel: memcpy+0x20/0x50
kernel: ucma_event_handler+0x532/0x560 [rdma_ucm]
kernel: ? __rpc_execute+0x608/0x620 [sunrpc]
kernel: cma_iw_handler+0x212/0x330 [rdma_cm]
kernel: ? iw_conn_req_handler+0x6e0/0x6e0 [rdma_cm]
kernel: ? enqueue_timer+0x86/0x140
kernel: ? _raw_write_lock_irq+0xd0/0xd0
kernel: cm_work_handler+0xd3d/0x1070 [iw_cm]
Fixes: e411e0587e ("RDMA/qedr: Add iWARP connection management functions")
Link: https://lore.kernel.org/r/20200616093408.17827-1-michal.kalderon@marvell.com
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The max_pkeys device attribute was not set in query device verb, set it to
one in order to account for the default pkey (0xffff). This information is
exposed to userspace and can cause malfunction
Fixes: 40909f664d ("RDMA/efa: Add EFA verbs implementation")
Link: https://lore.kernel.org/r/20200614103534.88060-1-galpress@amazon.com
Reviewed-by: Firas JahJah <firasj@amazon.com>
Reviewed-by: Yossi Leybovich <sleybo@amazon.com>
Signed-off-by: Gal Pressman <galpress@amazon.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In case of failure of alloc_ud_wq_attr(), the memory allocated by
rvt_alloc_rq() is not freed. Fix it by calling rvt_free_rq() using the
existing clean-up code.
Fixes: d310c4bf8a ("IB/{rdmavt, hfi1, qib}: Remove AH refcount for UD QPs")
Link: https://lore.kernel.org/r/20200614041148.131983-1-pakki001@umn.edu
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Fix the following sparse error by adding annotation to
cm_queue_work_unlock() that it releases cm_id_priv->lock lock.
drivers/infiniband/core/cm.c:936:24: warning: context imbalance in
'cm_queue_work_unlock' - unexpected unlock
Fixes: e83f195aa4 ("RDMA/cm: Pull duplicated code into cm_queue_work_unlock()")
Link: https://lore.kernel.org/r/20200611130045.1994026-1-leon@kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
