The tid of 11a station with WMM disable reported by FW is 0x10 in
tx completion. The tid 16 is mapped to a NULL txq since buffer
MMPDU capbility is not supported. Then 11a station's airtime will
not be registered due to NULL txq check. As a results, airtime of
11a station keeps unchanged in debugfs system.
Mask the tid along with IEEE80211_QOS_CTL_TID_MASK to make it in
the valid range.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.10-00047
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes coccicheck warning:
drivers/net/wireless/ath/ath10k/htt_rx.c:2143:2-31: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For tcp RX, the quantity of tcp acks to remote is 1/2 of the quantity
of tcp data from remote, then it will have many small length packets
on TX path of sdio bus, then it reduce the RX packets's bandwidth of
tcp.
This patch enable napi on RX path, then the RX packet of tcp will not
feed to tcp stack immeditely from mac80211 since GRO is enabled by
default, it will feed to tcp stack after napi complete, if rx bundle
is enabled, then it will feed to tcp stack one time for each bundle
of RX. For example, RX bundle size is 32, then tcp stack will receive
one large length packet, its length is neary 1500*32, then tcp stack
will send a tcp ack for this large packet, this will reduce the tcp
acks ratio from 1/2 to 1/32. This results in significant performance
improvement for tcp RX.
Tcp rx throughout is 240Mbps without this patch, and it arrive 390Mbps
with this patch. The cpu usage has no obvious difference with and
without NAPI.
call stack for each RX packet on GRO path:
(skb length is about 1500 bytes)
skb_gro_receive ([kernel.kallsyms])
tcp4_gro_receive ([kernel.kallsyms])
inet_gro_receive ([kernel.kallsyms])
dev_gro_receive ([kernel.kallsyms])
napi_gro_receive ([kernel.kallsyms])
ieee80211_deliver_skb ([mac80211])
ieee80211_rx_handlers ([mac80211])
ieee80211_prepare_and_rx_handle ([mac80211])
ieee80211_rx_napi ([mac80211])
ath10k_htt_rx_proc_rx_ind_hl ([ath10k_core])
ath10k_htt_rx_pktlog_completion_handler ([ath10k_core])
ath10k_sdio_napi_poll ([ath10k_sdio])
net_rx_action ([kernel.kallsyms])
softirqentry_text_start ([kernel.kallsyms])
do_softirq ([kernel.kallsyms])
call stack for napi complete and send tcp ack from tcp stack:
(skb length is about 1500*32 bytes)
_tcp_ack_snd_check ([kernel.kallsyms])
tcp_v4_do_rcv ([kernel.kallsyms])
tcp_v4_rcv ([kernel.kallsyms])
local_deliver_finish ([kernel.kallsyms])
ip_local_deliver ([kernel.kallsyms])
ip_rcv_finish ([kernel.kallsyms])
ip_rcv ([kernel.kallsyms])
netif_receive_skb_core ([kernel.kallsyms])
netif_receive_skb_one_core([kernel.kallsyms])
netif_receive_skb ([kernel.kallsyms])
netif_receive_skb_internal ([kernel.kallsyms])
napi_gro_complete ([kernel.kallsyms])
napi_gro_flush ([kernel.kallsyms])
napi_complete_done ([kernel.kallsyms])
ath10k_sdio_napi_poll ([ath10k_sdio])
net_rx_action ([kernel.kallsyms])
__softirqentry_text_start ([kernel.kallsyms])
do_softirq ([kernel.kallsyms])
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change log level from warn to dbg level of mpdu status
of sdio chip.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far, frames were forwarded regardless of the FCS correctness leading
to userspace applications listening on the monitor mode interface to
receive potentially broken frames, even with the "fcsfail" flag unset.
By default, with the "fcsfail" flag of a monitor mode interface
unset, frames with FCS errors should be dropped. With this patch, the
fcsfail flag is taken into account correctly.
Tested-on: QCA4019 firmware-5-ct-full-community-12.bin-lede.011
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
iw command only show rssi without each chain's rssi on sdio
iw wlan0 station dump
Station a0:40:a0:93:3e:de (on wlan0)
signal: -82 dBm
signal avg: -82 dBm
after this patch, it will show each chain's rssi on sdio
Station a0:40:a0:93:3e:de (on wlan0)
signal: -82 [-84, -88] dBm
signal avg: -82 [-84, -87] dBm
For QCA6174 PCIe, the ppdu have the correct rssi of each chain, it
indicate rssi of rx data by ath10k_htt_rx_h_signal. For sdio chip, the
rssi of each chain stored in rx management reported by firmware, the
ath10k_wmi_tlv_op_pull_mgmt_rx_ev which used for tlv wmi will get the
rssi of each chain and stored them in wmi_mgmt_rx_ev_arg, then indicate
them to mac80211. For non-tlv wmi chip, it will not get the rssi of each
chain and not indicate to mac80211, for non-tlv wmi chip, this patch will
not have impact. For tlv wmi chip, if the rssi of chain in mgmt is valid,
it will be indicate to mac80211, tested with QCA6174 PCIe/SDIO, the rssi
of 2 chain in mgmt is valid.
rssi of chains in mgmt of QCA6174 SDIO:
92096.652780: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[0]:70
92096.657324: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[1]:68
92096.662009: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[2]:128
92096.666647: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[3]:128
rssi of chains in mgmt of QCA6174 PCIe:
[ 1581.049816] ath10k_pci 0000:02:00.0: mgmt rssi[0]:17
[ 1581.049818] ath10k_pci 0000:02:00.0: mgmt rssi[1]:22
[ 1581.049821] ath10k_pci 0000:02:00.0: mgmt rssi[2]:128
[ 1581.049823] ath10k_pci 0000:02:00.0: mgmt rssi[3]:128
after apply this patch, the iw's rssi of PCIe do not changed, result is
same with before.
iw wlan0 station dump of QCA6174 PCIe:
Station 6c:e8:73:b8:92:dc (on wlan0)
signal: -70 [-77, -72] dBm
signal avg: -69 [-78, -72] dBm
iw wlan-5000mhz station dump of QCA9984 PCIe
connected with 2 client which has 2 chain:
Station 70:48:0f:1f:1a:b2 (on wlan-5000mhz)
signal: -47 [-55, -48, -87, -88] dBm
signal avg: -42 [-50, -43, -83, -86] dBm
Station ac:c1:ee:39:e3:83 (on wlan-5000mhz)
signal: -43 [-46, -45, -79, -84] dBm
signal avg: -43 [-46, -46, -82, -83] dBm
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Tested with QCA6174 PCIe with firmware WLAN.RM.4.4.1-00110-QCARMSWP-1.
Tested with QCA9984 PCIe with firmware 10.4-3.9.0.2-00040.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For RX, it has two parts, one is to read data from sdio, another
is to indicate the packets to upper stack. Recently it has only
one thread to do all RX things, it results that it is sequential
for RX and low throughout, change RX to parallel for the two parts
will increase throughout.
This patch move the indication to a workqueue, it results in
significant performance improvement on RX path.
Udp rx throughout is 200Mbps without this patch, and it arrives
400Mbps with this patch.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For sdio chip, if the rssi is not good, then it have some retry,
firmware will indicate the msdu list of a ppdu with a hole, it
means it lost the hole msdu, after the msdu retry from AP, the
hole msdu will indicate from firmware later. The hole msdu's PN
check will fail and the hole msdu will be dropped.
PN check fail example:
Sequence number PN number PN check status
3814 6101 success
3815 6102 success
3816 6103 success
3818 6105 success
3819 6106 success
3820 6107 success
3817 6104 fail
The correct logic is reorder the msdu list and then do PN check.
ieee80211_rx_reorder_ampdu of mac80211 will do the reorer logic
and then do PN check in ieee80211_rx_h_decrypt of mac80211.
example after reorder:
Sequence number PN number PN check status
3814 6101 success
3815 6102 success
3816 6103 success
3817 6104 success
3818 6105 success
3819 6106 success
3820 6107 success
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k will receive some message with invalid peer id from firmware.
reason is:
There are incoming frames to MAC hardware that NOT find relative
address search table, then peer id is invalid set by MAC hardware,
it is hardware's logic, so fix it in ath10k will be more convenient.
log:
ath10k_sdio mmc1:0001:1: Got RX ind from invalid peer: 65535
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware will report flag with HTT_RX_IND_MPDU_STATUS_TKIP_MIC_ERR
if MIC error, the flag will be used in mac80211.
ieee80211_rx_h_michael_mic_verify will check the flag and start TKIP
countermeasures.
Now countermeasure tests pass both with WPA only and WPA2/WPA mixed
mode.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lockdep warns at lockdep_assert_held(&ar->data_lock) in
ath10k_htt_rx_pn_check_replay_hl(). Acquire ar->data_lock before calling
ath10k_htt_rx_pn_check_replay_hl() to fix it.
Call trace:
ath10k_htt_rx_pn_check_replay_hl+0x118/0x134 [ath10k_core]
ath10k_htt_rx_proc_rx_ind_hl+0xd8/0x250 [ath10k_core]
ath10k_htt_t2h_msg_handler+0x148/0xf30 [ath10k_core]
ath10k_htt_htc_t2h_msg_handler+0x24/0x40 [ath10k_core]
ath10k_sdio_irq_handler+0x374/0xaa4 [ath10k_sdio]
Fixes: 130c774957 ("ath10k: add PN replay protection for high latency devices")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, change the following form:
sizeof(*rx) + (sizeof(struct htt_rx_indication_mpdu_range) * num_mpdu_ranges)
to :
struct_size(rx, mpdu_ranges, num_mpdu_ranges)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In tx_stats debugfs, txrate->flags may contain multiple bits. For
example, RATE_INFO_FLAGS_SHORT_GI could be set, and tx stats bytes
and packets will be not updated correctly.
Fix this issue by using bit operation to check txrate->flags.
Tested HW: QCA9984
Tested Firmware: 10.4-3.9.0.1-00007
Signed-off-by: Brandon Huang <yanghuan@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On high latency devices (SDIO, USB) ath10k did not handle fragmented frames and
all fragmented frames on receive path were lost in ath10k. Even a simple ping
test failed with fragmentation.
The fragmented packets are decapsulated based on the security mode, then the PN
is checked and the fragmented frame is passed to mac80211. mac80211 in
ieee80211_rx_h_defragment() will then combine the fragment frames and forward
to upper layers.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On high latency devices (SDIO, USB) ath10k did not do PN replay check, a data
frame with an invalid PN number was not discard as it should have been. So this
patch implements PN replay in ath10k. PN replay check for fragmented frames is
implemented in followup patch.
With low latency devices (PCI, AHB) hardware can store the data
frames's content to host memory directly and the firmware can fully reorder
data frames, and do PN replay check at the same time. But for high latency
devices all data frames will be received and stored in firmware's memory and it
is hard to do full reorder because of the memory size limitations in the
firmware. This is why the PN replay protections needs to be implemented in host
driver.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the handler for HTT_T2H_MSG_TYPE_SEC_IND event from firmware, which stores
PN for replay check implemented in the following patch.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HTT High Latency (ATH10K_DEV_TYPE_HL) does not use txdone_fifo at all, we don't
even initialise it by skipping ath10k_htt_tx_alloc_buf() in
ath10k_htt_tx_start(). Because of this using QCA6174 SDIO
ath10k_htt_rx_tx_compl_ind() will crash when it accesses unitialised
txdone_fifo. So skip txdone_fifo when using High Latency mode.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently there is no way for the driver to signal to mac80211 that it should
schedule a TXQ even if there are no packets on the mac80211 part of that queue.
This is problematic if the driver has an internal retry queue to deal with
software A-MPDU retry.
This patch changes the behavior of ieee80211_schedule_txq to always schedule
the queue, as its only user (ath9k) seems to expect such behavior already:
it calls this function on tx status and on powersave wakeup whenever its
internal retry queue is not empty.
Also add an extra argument to ieee80211_return_txq to get the same behavior.
This fixes an issue on ath9k where tx queues with packets to retry (and no
new packets in mac80211) would not get serviced.
Fixes: 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ht_idx (ht rate index) and idx (rate table index) are calculated based on
mcs index. This mcs index used in the above calculation should be 0-9 for
getting the correct ht_idx and idx.
Currently the mcs index used for the above calculations is mcs index which
can be 0-31 (in case of HT), leading to incorrect rate index and ht index values.
Fix the issue by obtaining mcs value from the ratecode reported by firmware
and use it for calculating ht_idx and idx (rate-table index).
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: e88975ca37 ("ath10k: dump tx stats in rate table format")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SGI is updated wrongly in tx stats table in debugfs per sta
entry. To know whether the packets/bytes are sent with SHORT GI,
test whether the SGI bit(ATH10K_RATE_INFO_FLAGS_SGI_BIT) is set or
not in the txrate flags.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The NSS data is updated incorrectly in the tx stats as the array
indexing starts from zero.
Fix the incorrect updation of NSS data in tx_stats by taking into
consideration the array index starting from zero.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SDIO firmware does not provide RSSI value to the host, it's only set to
zero. In that case don't report the value to mac80211. One risk here is that
value zero might be a valid value with other firmware, currently there's no way
to detect that.
Without the fix, the rssi value indicated by iw changes between the actual
value and -95.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "data" tx completion event. Host extracts ack rssi
values of data packets from their tx completion event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use SPDX identifiers everywhere in ath10k.
Makefile was incorrectly marked in commit b24413180f ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license"), fix that as well.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If supported, update transmit airtime in mac80211 with the airtime
values reported by the firmware. TX airtime of the PPDU is reported
via HTT data TX completion indication message.
A new service flag 'WMI_SERVICE_REPORT_AIRTIME' is added to advertise
the firmware support. For firmwares which do not support this feature,
TX airtime is calculated in the driver using TX bitrate.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.6.1-00841
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The airtime of a transmitted frame will be estimated from last used tx rate
which the firmware reports with the peer stats feature
(WMI_SERVICE_PEER_STATS). The airtime is computed on the tx path and it
will be reported to mac80211 upon tx completion.
This change is based on Kan's orginal commit in Chromium tree
("CHROMIUM: ath10k: Implementing airtime fairness based TX scheduler")
ref: https://chromium-review.googlesource.com/588190
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Signed-off-by: Kan Yan <kyan@google.com>
[rmanohar@codeaurora.org: ported only the airtime computation]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
[toke@redhat.com: Rebase to mac80211-next, add test note]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k maintains common txqs list for all stations. This txq
management can be removed by migrating to mac80211 txq APIs
and let mac80211 handle txqs reordering based on reported airtime.
By doing this, txq fairness maintained in ath10k i.e processing
N frames per txq is removed. By adapting to mac80211 APIs,
ath10k will support mac80211 based airtime fairness algorithm.
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Tested-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wow pause iface config controls the PCI D0/D3-WOW cases for pcie
bus state. Firmware does not expects WOW_IFACE_PAUSE_ENABLED config
for bus/link that cannot be suspended ex:snoc and does not trigger
common subsystem shutdown.
Disable interface pause wow config for integrated chipset(WCN3990)
for correct WOW configuration in the firmware.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware sends the tx_duration for each in HTT_T2H_MSG_TYPE_PEER_STATS
msg. Fill the tx_duration sent by firmware in the tx stats information
per STA.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some hardwares variants (QCA99x0) are limiting msdu deaggregation with
some threshold value(default limit in QCA99x0 is 64 msdus), it was introduced to
avoid excessive MSDU-deaggregation in error cases. When number of sub frames
exceeds the limit, target hardware will send all msdus starting from present
msdu in RAW format as a single msdu packet and it will be indicated with
error status bit "RX_MSDU_END_INFO0_MSDU_LIMIT_ERR" set in rx descriptor.
This msdu frame is a partial raw MSDU and does't have first msdu and ieee80211
header. It caused below warning message.
[ 320.151332] ------------[ cut here ]------------
[ 320.155006] WARNING: CPU: 0 PID: 3 at drivers/net/wireless/ath/ath10k/htt_rx.c:1188
In our issue case, MSDU limit error happened due to FCS error and generated
this warning message.
This fixes the warning by handling the MSDU limit error. If msdu limit error
happens, driver adds first MSDU's ieee80211 header and sets A-MSDU present bit
in QOS header so that upper layer processes this frame if it is valid or drop it
if FCS error set. And removed the warning message, hence partial msdus without
first msdu is expected in msdu limit error cases.
Tested on QCA9984, Firmware 10.4-3.6-00104
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mesh path metric needs tx rate information from ieee80211_tx_status()
call but in ath10k there is no mechanism to report tx rate information
via ieee80211_tx_status(), the tx rate is only accessible via
sta_statiscs() op.
Per peer tx stats has tx rate info available, Tx rate is available
to ath10k driver after every 4 PPDU sent in the air. For each PPDU,
ath10k driver updates rate informattion to mac80211 using
ieee80211_tx_rate_update().
Per peer txrate information is updated through per peer statistics
and is available for QCA9888/QCA9984/QCA4019/QCA998X only
Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00053
Tested on QCA998X with firmware-5.bin_10.2.4-1.0-00036
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When processing HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND, if the length of a msdu
is larger than the tailroom of the rx skb, skb_over_panic issue will happen
when calling skb_put. In monitor mode, amsdu will be handled in this path, and
msdu_len of the first msdu_desc is the length of the entire amsdu, which might
be larger than the maximum length of a skb, in such case, it will hit the issue
upon.
To fix this issue, process msdu list separately for monitor mode.
Successfully tested with:
QCA6174 (FW version: RM.4.4.1.c2-00057-QCARMSWP-1).
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
[kvalo@codeaurora.org: cosmetic cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds the tx statistics pkts/bytes dump
in rate table format.
Dump format table is similar to http://mcsindex.com/
Tested on QCA9984/QCA4019/QCA988x
Firmware: 10.4-3.5.3-00057
10.2.4-1.0-00037
command:
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/
stations/<MACADDR>/tx_stats
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We added an unnecessary condition here in commit a904417fc8 ("ath10k:
add extended per sta tx statistics support"). "legacy_rate_idx" is a u8
so it can't be negative. The caller doesn't pass negatives either. I
have deleted this code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, the error handling for the call to function
ath10k_get_legacy_rate_idx() doesn't work because
*rate_idx* is of type u8 (8 bits, unsigned), which
makes it impossible for it to hold a value less
than 0.
Fix this by changing the type of variable *rate_idx*
to s8 (8 bits, signed).
Addresses-Coverity-ID: 1473914 ("Unsigned compared against 0")
Fixes: 0189dbd71c ("ath10k: get the legacy rate index to update the txrate table")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.20. Major changes:
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
Special HTT RX handling for high latency interfaces.
Since no DMA physical addresses are used in the RX ring
config message (this is not supported by the high latency
devices), no RX ring is allocated.
All RX skb's are allocated by the driver and passed directly
to mac80211 in the HTT RX indication handler.
A nice side effect of this is that no huge buffer will be
allocated with dma_alloc_coherent. On embedded systems with
limited memory resources, the allocation of the RX ring is
prone to fail.
Some tweaks made to "make it work":
Removal of protected bit in 802.11 header frame control field.
The chipset seems to do hw decryption but the frame_control
protected bit is still set.
This is necessary for mac80211 not to drop the frame.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initial (empty) HTT RX ops for high latency devices.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Average ack rssi value is weighted average of ack rssi for
no of msdu's has been sent.
This feature is enabled by the host driver if firmware is capable.
After receiving event from host, firmware allocates the necessary
memory to store the ack_rssi for data packets during the init time.
After each successful transmission, If tx completion status is OK
and 24th bit is set in HTT message header then host will fetch the
ack_rssi else host can ignore the ack_rssi field.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds per station tx statistics support.
Per station tx stats include
- pkts/bytes transmitted at all possible rates(mcs/nss/bw/gi).
- ACK fails count
- ampdu bytes/pkts transmitted at all possible rates(mcs/nss/bw/gi).
- BA fails count
Tested on QCA9984/QCA4019/QCA988x
Firmware: 10.4-3.5.3-00057
10.2.4-1.0-00037
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Get the legacy rate index to update the pkts/bytes counter
against each possible tx rate.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Both WARN_ON() and WARN_ON_ONCE() already contain unlikely().
Signed-off-by: Igor Stoppa <igor.stoppa@huawei.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Michal Kazior <michal.kazior@tieto.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: Linux Wireless Mailing List <linux-wireless@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While debugging driver crashes related to a buggy firmware
crashing under load, I noticed that ath10k_htt_rx_ring_free
could be called without being under lock. I'm not sure if this
is the root cause of the crash or not, but it seems prudent to
protect it.
Originally tested on 4.16+ kernel with ath10k-ct 10.4 firmware
running on 9984 NIC.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added for the same reason as the TX wrappers.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
