When a FTM request is aborted, the driver sends the abort command to
the fw and waits for a response. When the response arrives, the driver
calls cfg80211_pmsr_complete() for that request.
However, cfg80211 frees the requested data immediately after sending
the abort command, so this may lead to use after free.
Fix it by clearing the request data in the driver when the abort
command arrives and ignoring the fw notification that will come
afterwards.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Fixes: fc36ffda32 ("iwlwifi: mvm: support FTM initiator")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The new API requires the driver to set the frame format
(legacy, HT, VHT etc.) to be used for the measurement.
The new API also supports 11az and secured measurement, but
these are not supported by the driver for now.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This makes boot uniformly boottime and tai uniformly clocktai, to
address the remaining oversights.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/20190621203249.3909-2-Jason@zx2c4.com
When the interface that is requesting an FTM measurement is connected
to a BSS, it is possible that the FTM request was originated by an
RRM request from the AP. In this case the station needs to report
the measurement start time in terms of the TSF of the AP.
Since there is no indication in the FTM request itself if the TSF
is needed, always report the TSF if the station is associated.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The range response notification API has changed to add a value that
indicates the confidence of the rtt result.
Support the new API and print the rtt confidence for debug.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
do_div() expects unsigned operands and otherwise triggers a warning like:
drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c:465:2: error: comparison of distinct pointer types ('typeof ((rtt_avg)) *' (aka 'long long *') and 'uint64_t *' (aka 'unsigned long long *')) [-Werror,-Wcompare-distinct-pointer-types]
do_div(rtt_avg, 6666);
^~~~~~~~~~~~~~~~~~~~~
include/asm-generic/div64.h:222:28: note: expanded from macro 'do_div'
(void)(((typeof((n)) *)0) == ((uint64_t *)0)); \
~~~~~~~~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~~
1 error generated.
Change the do_div() to the simpler div_s64() that can handle
negative inputs correctly.
Fixes: 937b10c0de ("iwlwifi: mvm: add debug prints for FTM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add debug prints for FTM results info. These prints are used by
tests automation.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FTM new API uses API TLV bit 15. The driver mistakenly uses
this bit for beacon filter API, although no TLV was assigned for
the beacon filter API. For now, make beacon filter use bit 16
instead (not set by the fw anyway). Once a TLV is assigned to the
beacon filter API it should be updated.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for FTM initiator, i.e. peer measurements with FTM
if the firmware supports FTM.
Additionally, add two defines we depend on in
include/linux/ieee80211.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
