We don't support the FPGA versions of this card combination anymore.
Remove the cfg mangling that tries to load it and all the relevant
structures.
Change-Id: I190652101afcab682cfba873d062992f11efca32
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A couple of SoCs, which can be recognized by PCI device IDs 0xA0F0 and
0x43F0, need a longer wait for the xtal to stabilize. To handle this,
add a new trans_cfg structure for Qu devices with a larger
xtal_latency value and apply them to the devices recognized by these
IDs. Also add a flag that allows us to inform the FW that the low
latency xtal should be used.
Change-Id: I8a14c6af45ea14d8e7f1ef38a589158f38d0c0ea
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we identify the correct cfgs with the new tables for Qu step
C and QuZ with Jf, we can remove the mangling we do later on.
Change-Id: Ic01ce67db147e897ad2424f0e05a70a00d2c620e
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
All the QnJ devices have a similar matching to the other Qu devices,
but needs a different configuration. Convert the QnJ devices to the
new table accordingly.
Change-Id: If236ef3d0da3e605a3379922818f5897e0affd7e
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new generic iwl_trans structures for these devices and apply the
correct cfg depending on the device characteristics.
Since we have to match Qu with IWL_CONFIG_ANY, we also need to move
the Hr devices to the new table, but for now we keep matching on PCI
device and subsystem device IDs.
Change-Id: I14e9146a99621ff11ce50bc746a4b88af508fee0
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to use different firmware versions for different HW steps with
certain devices. Prepare for this differentiation by adding HW step
to the new device table.
Change-Id: Ib1afb7b0c89e9dc2d26e6d32ea19e978c17ba1dd
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These values are selected based on the PCI device ID, so the decision
to use them can be made early. By moving them to the trans_cfg, we
avoid duplicating the large cfg structs for small pieces of
data (sometimes a single boolean). This will also allow us to make
more decisions based on, for instance, the SoC type in used.
The trans_cfg concept changes a bit, because previously it was used
only to boot the device before reading further characteristics and now
it also contains more data that is associated with the device ID.
Change-Id: Ib71b07ea9e322eb74571dc5e8aa58f17eece5c9c
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl9560_2ac_cfg struct is used for PNJ devices and the
configuration is the same as iwl9260_2ac_cfg, so we can remove the
former to avoid redundancy.
Change-Id: I17ac1802f00bd80006930b922a9fc21df60e3c16
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TH1 devices can now be fully differentiated by using the device
parameters we have (particularly the RF_TYPE). Start using these
parameters instead of hardcoding to specific subsystem device IDs.
This also fixes the name of one of the TH1 devices that was
erroneously using the 9260 struct and renames 9160 to 9162.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200309091348.18d4304b5454.Ib168d186da88393e9ec46f0fca523edb48d9138e@changeid
Devices that also include a GNSS module have different names, so add a
new device option to differentiate them, according to the values we
have in the modules section of the subsystem device ID.
Additionally, convert the two applicable devices to use this value
instead of hardcoded subsystem IDs.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200309091348.1f958e558d05.I45492bb57cbbeb4cc0ec84313bade4def7377a27@changeid
* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEF3LNfgb2BPWm68smoUecoho8xfoFAl4ZmgQACgkQoUecoho8
xfqEmQ/9EuV/rOANfiPQUL1wKl3u2tT8DviH7DFcT7z18U6ghDxn3ElRKTt9bz3T
yfr1QYuttW9oQibgF75bosp7beNJRf6UUqfv175JxVhLqTHDmgiFzPD67SceBcBB
bT1n0isXzhzZx0tZQNNXPYgnTy42mTJKY86l6imPrji41WuHGCUNAZnJj57BCeDY
LSX4JDO6wz/KaNznwlMGkDn3TIZFeqNh9/j0vDXzHA/FPUvq8voU7/alcE2DgjqC
vSxunFclCSoKX7/qoqnQE5tzBTsGh8LJHI7sD3CAueuDP7vacMJCY//IVLNkmfyA
03zIt26OLT9irc98uEhwc2AuyDBmAYZd3O7kfEmeg7yp5ffLbyWX0uefhi4SQI81
/0SJeY7Ylf8NVarE2QJmmTOYft8W9v71IWCdgmx1mRotQtebhNzWLho2bXAdLwwj
OFPb9lXCdgPqCmBgE2I1PP0iWtEOvkAzb+mrmpclElShYf63Py3mf9Y5cjoqLi2e
QZtjLCMpGNh3aZPSjVDMgXMZv6WxLB/fFmX3O8NDgBExaKh0rvG7j7b8A4URonVq
I4ngnBUSXzZ48yiAmlKL++QanuHXsHkDuLOiErKXiC8wwWE+7EGopxZ4vq7oSkao
mBdoB4HcQYfO+sO+J8rWNZdp4EMeXyBDW3ce1d7lTqyEjPbMM+8=
=Ovcw
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2020-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First set of patches intended for v5.6
* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;
We have a lot of mostly duplicated data structures that are repeated
only because the device name string is different. To avoid this, move
the string from the cfg to the trans structure and add it
independently from the rest of the configuration to the PCI mapping
tables.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new device table that contains information that can be checked
at runtime in order to decide which configuration to use. This allows
us to map the full cfg independently from the tran-specific
configuration.
This is the first step in creating the new table. Subsequent patches
will add the possibility of checking different values at runtime in
order to make the decision.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With the new concept of separating the trans-specific (trans_cfg) data
from the rest of the cfg, we will start mapping only the trans_cfg
part to the PCI device ID/subsystem device ID. So we can assume that
the data passed to the probe function contains the trans_cfg, but
since the full cfg still contains the trans_cfg at the beginning, we
can allow a full cfg to be passed as well. This makes it easier to
convert the existing tables one by one.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We needed this abstraction for some CSR registers for
IWL_DEVICE_22560, but that has been removed, so we don't need the
abstraction anymore. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A few configuration structures were either not referenced anymore or
assigned to devices IDs that were not in use anymore. Remove them.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For HE-capable devices, we need to allocate more receive buffers as
there could be 256 frames aggregated into a single A-MPDU, and then
they might contain A-MSDUs as well. Until 22000 family, the devices
are able to put multiple frames into a single RB and the default RB
size is 4k, but starting from AX210 family this is no longer true.
On the other hand, those newer devices only use 2k receive buffers
(by default).
Modify the code and configuration to allocate an appropriate number
of RBs depending on the device capabilities:
* 4096 for AX210 HE devices, which use 2k buffers by default,
* 2048 for 22000 family devices which use 4k buffers by default,
* 512 for existing 9000 family devices, which doesn't really
change anything since that's the default before this patch,
* 512 also for AX210/22000 family devices that don't do HE.
Theoretically, for devices lower than AX210, we wouldn't have to
allocate that many RBs if the RB size was manually increased, but
to support that the code got more complex, and it didn't really
seem necessary as that's a use case for monitor mode only, where
hopefully the wasted memory isn't really much of a concern.
Note that AX210 devices actually support bigger than 12-bit VID,
which is required here as we want to allocate 4096 buffers plus
some for quick recycling, so adjust the code for that as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This reverts commit 968dcfb490.
Both that commit and commit 809805a820
attempted to fix the same bug (dead assignments to the local variable
cfg), but they did so in incompatible ways. When they were both merged,
independently of each other, the combination actually caused the bug to
reappear, leading to a firmware crash on boot for some cards.
https://bugzilla.kernel.org/show_bug.cgi?id=205719
Signed-off-by: Anders Kaseorg <andersk@mit.edu>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When converting the wrong qu configurations in an earlier commit, I
accidentally swapped 0x2720 and 0x30DC. Instead of converting 0x2720,
I converted 0x30DC. Undo 0x30DC and convert 0x2720.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A bunch of the entries for qnj were wrong. The 9460 device doesn't
exist, so update them to 9461 and 9462. There are still a bunch of
other occurrences of 9460, but that will be fixed separately.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some entries for PCI ID 0x2720 were using iwl9260_2ac_cfg, but the
correct is to use iwl9260_2ac_cfg_soc. Fix that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two patches were sent out of order: one removed some conditions from
an if and the other moved the code elsewhere. When sending the patch
that moved the code, an older version of the original code was moved,
causing the "make QnJ exclusive" code to be essentially undone.
Fix that by removing the inclusive conditions from the check again.
Fixes: 809805a820 ("iwlwifi: pcie: move some cfg mangling from trans_pcie_alloc to probe")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There were a bunch of devices with qu and jf that were loading the
configuration with pu and jf, which is wrong. Fix them all
accordingly. Additionally, remove 0x1010 and 0x1210 subsytem IDs from
the list, since they are obviously wrong, and 0x0044 and 0x0244, which
were duplicate.
Cc: stable@vger.kernel.org # 5.1+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Stop accessing the trans configuration via the iwl_cfg structure and
always access it via the iwl_trans structure. This completes the
requirements to disassociate the trans-specific configuration from the
rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a pointer to the iwl_trans structure and point it to the trans
part of the cfg. This is the first step in disassociating the trans
configuration from the rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of accessing the iwl_config_trans_params from the cfg that is
stored in the trans struct, pass this structure directly to functions
that need it during trans_alloc. This will be useful to isolate the
elements needed during allocation and pass them separately before the
actual cfg struct is known.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of setting the cfg to iwl_trans already during allocation, set
it only later when we have had the time to decide which cfg to use.
This is part of the effort to be able to decide the cfg based on HW
revision and RF ID after iwl_trans_alloc() has been called.
For now, since we still have a bunch of code checking the HW revision
and the RF ID, we set iwl_trans->cfg early, even before we decided the
real cfg to use. We only use the trans configuration at this point,
so this is fine for now. In the future, the trans configuration will
be completely independent from the rest of the config structure, so
we'll be able to avoid this.
Additionally, we can't access the PRPH registers in iwl_trans_alloc()
anymore, so move the HW REV C-step check for family 8000 code later to
the probe function as well. This step is probably not necessary, but
if that's the case it should be removed separately later on.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There were a couple of special handling to find the correct cfg inside
iwl_trans_pcie_alloc(). Move them to iwl_pci_probe() so they're
together with the rest of the decisions.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This means:
1) stop calling pm_runtime_resume when starting the hardware
2) removing the unneeded low_power parameter to start / stop hw / fw
transport ops
3) squashing transport functions that are now the same
_iwl_trans_pcie_start_hw / iwl_trans_pcie_start_hw
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove the now unneeded functions that called those from the
transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is always set to IWL_PLAT_PM_MODE_DISABLED
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This flag should never be set unless integration work with the
platform is done. We don't support any platforms officially and don't
plan to do so in the near future, so we can remove this option
entirely in order to avoid having it enabled by mistake.
This has been marked with "depends on EXPERT", so there shouldn't be
many systems running with it set. And, if there are systems, they
should not be using this flag.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We were erroneously assigning the new configuration to a local
variable cfg, but that was not being assigned to anything, so the
change was getting lost. Assign directly to iwl_trans->cfg instead.
Fixes: 5a8c31aa63 ("iwlwifi: pcie: fix recognition of QuZ devices")
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We need to use a different firmware for C0 versions of killer Qu NICs.
Add structures for them and handle them in the if block that detects
C0 revisions.
Additionally, instead of having an inclusive check for QnJ devices,
make the selection exclusive, so that switching to QnJ is the
exception, not the default. This prevents us from having to add all
the non-QnJ cards to an exclusion list. To do so, only go into the
QnJ block if the device has an RF ID type HR and HW revision QnJ.
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190821171732.2266-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the HW revision of Qu devices we found is QuZ, then we need to
switch the configuration accordingly in order to use the correct FW.
Add a block of ifs in order do that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a few PCI ID'S for 9000 series.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for C-step devices. Currently we don't have a nice way of
matching the step and choosing the proper configuration, so we need to
switch the config structs one by one.
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
