* Silk board with R-Car E2 (r8a7794) SoC
- Add r1ex24002 EEPROM to DT
Magnus Damm says "Extend the Silk board support to include U14 which is
an I2C based EEPROM hooked up to the I2C1 bus."
- Add GPIO keys to DT
Magnus Damm says "Extend the Silk board support to include SW3, SW4,
SW6 and SW12. They are all connected via GPIO lines and handled by the
gpio-keys driver"
* Marzen board with R-Car H1 (r7a7779) SoC
- Add SDHI0 VCCQ Regulator
Magnus Damm says "Add support for the on-board voltage regulator hooked
up to GPIO3_20 on r8a7779 Marzen. The board schematics describes the
regulator as U4 TPS2110A. Input wise, U4 has D0 fixed to ground, D1
tied to GPIO3_20 while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V.
OUT goes to the pull-ups for the data pins of SDHI0."
* Porter board with R-Car M3W (r8a7791) SoC
- Fix HDMI output routing
Laurent Pinchart says "The HDMI encoder is connected to the RGB output
of the DU, which is port@0, not port@1."
* iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) and
iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
- Enable cmt0
* Stout board with R-Car H2 (r8a7790) SoC
- Initial support
* Lager board with R-Car H2 (r8a7790) SoC
- Add CEC clock for HDMI transmitter
Niklas Söderlund says "The adv7511 on the Lager board has a 12 MHz
fixed clock for the CEC block. Specify this in the dts to enable CEC
support."
- Move cec_clock to root node
By definition nodes without a bus address do not belong on the bus
* kzm9d board with EMMA Mobile EV2 (EMEV2) SoC
- Fix "debounce-interval" property misspelling
* RZ/G1M (r8a7743) and RZ/G1H (r8a7745) SoCs
- Add IPMMU DT nodes
- Add VSP support
* R-Car Gen2 boards
- Use I2C demuxer for
This allows run-time switching between alternate I2C IP blocks
* R-Car Gen2 and RZ/G1 SoCs
- Clean up DT files to ease future maintenance
+ add soc node for IP attached to the bus
+ sort subnodes of soc and root node
+ consistently use single space after =
* R-Car H2 (r8a7790), M3-W (r8a7791) and M3-N (r7a7793) SoCs
- Reduce size of thermal registers
According to the "User's Manual: Hardware" v2.00 the registers at base
0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the
case on the r8a73a4 (R-Mobile APE6).
This should not have any runtime affect as mapping granularity is
PAGE_SIZE.
-----BEGIN PGP SIGNATURE-----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=dZnw
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v4.17" from Simon Horman:
* Silk board with R-Car E2 (r8a7794) SoC
- Add r1ex24002 EEPROM to DT
Magnus Damm says "Extend the Silk board support to include U14 which is
an I2C based EEPROM hooked up to the I2C1 bus."
- Add GPIO keys to DT
Magnus Damm says "Extend the Silk board support to include SW3, SW4,
SW6 and SW12. They are all connected via GPIO lines and handled by the
gpio-keys driver"
* Marzen board with R-Car H1 (r7a7779) SoC
- Add SDHI0 VCCQ Regulator
Magnus Damm says "Add support for the on-board voltage regulator hooked
up to GPIO3_20 on r8a7779 Marzen. The board schematics describes the
regulator as U4 TPS2110A. Input wise, U4 has D0 fixed to ground, D1
tied to GPIO3_20 while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V.
OUT goes to the pull-ups for the data pins of SDHI0."
* Porter board with R-Car M3W (r8a7791) SoC
- Fix HDMI output routing
Laurent Pinchart says "The HDMI encoder is connected to the RGB output
of the DU, which is port@0, not port@1."
* iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) and
iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
- Enable cmt0
* Stout board with R-Car H2 (r8a7790) SoC
- Initial support
* Lager board with R-Car H2 (r8a7790) SoC
- Add CEC clock for HDMI transmitter
Niklas Söderlund says "The adv7511 on the Lager board has a 12 MHz
fixed clock for the CEC block. Specify this in the dts to enable CEC
support."
- Move cec_clock to root node
By definition nodes without a bus address do not belong on the bus
* kzm9d board with EMMA Mobile EV2 (EMEV2) SoC
- Fix "debounce-interval" property misspelling
* RZ/G1M (r8a7743) and RZ/G1H (r8a7745) SoCs
- Add IPMMU DT nodes
- Add VSP support
* R-Car Gen2 boards
- Use I2C demuxer for
This allows run-time switching between alternate I2C IP blocks
* R-Car Gen2 and RZ/G1 SoCs
- Clean up DT files to ease future maintenance
+ add soc node for IP attached to the bus
+ sort subnodes of soc and root node
+ consistently use single space after =
* R-Car H2 (r8a7790), M3-W (r8a7791) and M3-N (r7a7793) SoCs
- Reduce size of thermal registers
According to the "User's Manual: Hardware" v2.00 the registers at base
0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the
case on the r8a73a4 (R-Mobile APE6).
This should not have any runtime affect as mapping granularity is
PAGE_SIZE.
* tag 'renesas-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (47 commits)
ARM: dts: silk: Add GPIO keys to DT
ARM: dts: silk: Add r1ex24002 EEPROM to DT
ARM: dts: marzen: Add SDHI0 VCCQ Regulator
ARM: dts: stout: Initial r8a7790 Stout board support
ARM: dts: lager: Move cec_clock to root node
ARM: dts: kzm9d: Fix "debounce-interval" property misspelling
ARM: dts: gose: use demuxer for I2C4
ARM: dts: gose: use demuxer for I2C2
ARM: dts: silk: use demuxer for I2C1
ARM: dts: alt: use demuxer for I2C1
ARM: dts: porter: use demuxer for I2C2
ARM: dts: koelsch: use demuxer for I2C4
ARM: dts: koelsch: use demuxer for I2C2
ARM: dts: lager: use demuxer for IIC3/I2C3
ARM: dts: lager: use demuxer for IIC2/I2C2
ARM: dts: r8a7745: Add VSP support
ARM: dts: r8a7743: Add VSP support
ARM: dts: r8a7745: Add IPMMU DT nodes
ARM: dts: r8a7743: Add IPMMU DT nodes
ARM: dts: r8a7745: sort subnodes of soc node
...
Support for the VDE is added on Tegra30 along with some general cleanup
and some improvements to the various Toradex boards.
-----BEGIN PGP SIGNATURE-----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=Dqxp
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.17-arm-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Pull "ARM: tegra: Device tree changes for v4.17-rc1" from Thierry Reding:
Support for the VDE is added on Tegra30 along with some general cleanup
and some improvements to the various Toradex boards.
* tag 'tegra-for-4.17-arm-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: apalis-tk1: Support v1.2 hardware revision
ARM: tegra: apalis-tk1: Copyright period, spurious newlines
ARM: tegra: apalis-tk1: Hog group for ethernet, PCIe, reset GPIOs
ARM: tegra: apalis-tk1: Add missing as3722 gpio0 configuration
ARM: tegra: apalis-tk1: Activate PWM pin muxing for pwm3
ARM: tegra: apalis-tk1: Set critical trips
ARM: tegra: apalis/colibri: Remove unneeded reg property
ARM: tegra: apalis/colibri: Use correct compatible for RTC
ARM: tegra: Fix I2C bus frequencies on Apalis/Colibri
ARM: tegra: venice2: Remove duplicate pcie-1 node
ARM: tegra: beaver: Remove invalid uses of rsvd1
ARM: tegra: Use proper IRQ type definitions
ARM: tegra: Fix ULPI regression on Tegra20
ARM: tegra: Add unit address to VDE IRAM area
ARM: tegra: Add video decoder node on Tegra30
ARM: tegra: Add IRAM node on Tegra30
The first and second patches fix the regulator support for the Bananapi M2
board.
The last one updates my email address in MAINTAINERS.
-----BEGIN PGP SIGNATURE-----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=GQc4
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Pull "Allwinner Fixes for 4.16" from Maxime Ripard:
The first and second patches fix the regulator support for the Bananapi M2
board.
The last one updates my email address in MAINTAINERS.
* tag 'sunxi-fixes-for-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
MAINTAINERS: update email address for Maxime Ripard
ARM: dts: sun6i: a31s: bpi-m2: add missing regulators
ARM: dts: sun6i: a31s: bpi-m2: improve pmic properties
Fixes the warning "GIC: PPI13 is secure or misconfigured" by
changing the interrupt type from level_low to edge_raising
Signed-off-by: Philipp Puschmann <pp@emlix.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
For consistency with all other serial pins, add this pullup. It also
prevents the signal from floating and so consuming a useless extra amount
of power in crowbarred state if nothing is connected to RX.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
For consistency with all other serial pins, add this pullup. It also
prevents the signal from floating and so consuming a useless extra amount
of power in crowbarred state if nothing is connected to RX.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Remove pullup on uart TX signals, they are push-pull outputs thus
pullups are pointless.
Add pullup on uart RX signals, they prevent the RX signals to be left
floating and so consuming a useless extra amount of power in crowbarred
state if nothing is connected to RX.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There are only 19 PIOB pins having primary names PB0-PB18. Not all of them
have a 'C' function. So the pinctrl property mask ends up being the same as the
other SoC of the at91sam9x5 series.
Reported-by: Marek Sieranski <marek.sieranski@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Update the "gpio-ranges" property of the CBUS GPIO controller on Meson8b
because it only provides 83 GPIOs.
The GPIO definitions in include/dt-bindings/gpio/meson8b-gpio.h
inherited all GPIOs from Meson8 until recently. However, Meson8b does
not support all GPIOs which are supported by Meson8 (Meson8b doesn't
have a GPIOZ bank, most of the pins from the GPIODV bank are missing on
Meson8b - just to name a few differences).
The actual number of GPIOs is only 83, instead of 120 from Meson8 plus
the 10 GPIOs from the DIF bank on Meson8b.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Odroid C1 features a microSD slot. This patch adds the necessary
DT bindings to support it.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
These are needed to use the n_gsm driver for TS 27.010 UART
multiplexing. Note that support for the OOB wake gpio is still
missing so the UART is not yet usable for n_gsm.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Configure MDM6600 USB PHY.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have a USB OCHI PHY on port 1 for mdm6600. Port 2 is using transceiverless
logic (TLL) for USB EHCI for w3glte modem.
Let's also fix the node name to use usb-phy while at it.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds syscon property for specifying soc-glue core into
device-tree of PXs2 SoC.
Currently, soc-glue core is used for changing the state of S/PDIF
signal output pin to signal output state or Hi-Z state.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The xref_xtal clock is used by twl6040 as mclk. It is needed for the HPPLL
internally.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clock is directly sourced from sys_clkin, and provides an external
output clock for (typically) TWL6040 chip.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pad configuration area under control module wkup has some miscellaneous
config registers, that are not pinmux related. Add a separate area for
these, and add support for syscon / clocks under this new area.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
USB1 port is micro-AB type and can function as peripheral
as well as host. Enable dual-role mode for USB1.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the actual VGA DAC bridge that is used in the
Versatile AB, and sets the mode to 640x480 VGA.
The "clcd" clock was incorrectly named, the proper name
(from bindings) is "clcdclk". So far drivers survived
by just getting the first clock, but future drivers will
use named clocks.
We add the panel connector to the
"arm,versatile-tft-panel" as well, the signals actually
fork on the board, reaching both the VGA DAC and the
display connector.
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Versatile board can be equipped with a interface board
just named "IB2". This was created in the early 2000s for
prototyping GSM candybar phone form factor products.
The IB2 board contains:
- Cascaded interrupt controller
- Enfora Enabler GSM0308 quad-band module with antenna and
separate audio jack
- Keypad with joystick
- Sanyo 2.5" color display
- A 28-pin connector for mounting a camera
This adds a DTS file for the combination of the Versatile AB
with an IB2 daughterboard mounted, making the LED blink and
making the system controller available for drivers, such as
the panel driver.
The device tree bindings already exist in
Documentation/devicetree/bindings/arm/arm-boards.
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Cubieboard4 has a dumb VGA DAC connected to the output of LCD0,
providing VGA output through the onboard VGA connector. The DDC lines
are connected to i2c3.
The VGA DAC is a GM7123, which is compatible with Analog Devices'
ADV7123, except it only takes 3.3V power, and has a lower standby power
consumption. The datasheet found online lists "Chengdu GoldTel Electronical
Technology Co., Ltd." as its designer. The company changed its name in
2014 to "Chengdu Corpro Technology Co., Ltd.". Their website lists similar
ICs, but not actually the GM7123.
Enable the display pipeline with the VGA DAC and connector, and i2c3
for DDC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 supports RGB888 with H/V sync from LCD0. Add a pinmux setting
for the needed pins.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This patch adds some device nodes for the PCIe function block and updates
related pinmux.
Moreover, we add interrupt-map properties in both parent and children as
the chip only has one IRQ per slot that is connected to all INTx and get
propagated through the bridges and it also represents the root ports own
interrupts.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The H3 has an ARM Mali 400 GPU, so add binding to our DT.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
It should be good that no use "_" is in DT node name. Consequently,
those nodes in certain files which have an inappropriate name containing
"_" are all being replaced with "-".
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The property pinctrl-names is totally superfluous. It would be good to
remove the property to keep the node neatness. There is actually
unnecessary to set up any pins for data path TRGMII between main SoC and
MT7530. Furthermore, it's more reasonable for the pin setup of control
path MDIO bus is being placed inside the node of ethernet controller.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
On bpi-r2 board, totally there're four UARTs which we usually called
uart[0-3] helpful to extend slow-I/O devices. Among those ones, uart2 has
dedicated pin slot which is used to console log. uart[0-1] appear at the
40-pins connector and uart3 has no pinout, but just has test points (TP47
for TX and TP48 for RX, respectively) nearby uart2, but we don't enable
uart3 in the patch. The missing pinctrl is also being supplemented for
those newly added devices.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Both mmc devices on bananapi-r2 board should all use the fixed regulators
as their power source instead of PMIC MT6323 exports.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Extend the Silk board support to include SW3, SW4, SW6 and SW12. They
are all connected via GPIO lines and handled by the gpio-keys driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Extend the Silk board support to include U14 which is an I2C based EEPROM
hooked up to the I2C1 bus.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the on-board voltage regulator hooked up to GPIO3_20
on r8a7779 Marzen. The board schematics describes the regulator as U4
TPS2110A. Input wise, U4 has D0 fixed to ground, D1 tied to GPIO3_20
while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V. OUT goes to the
pull-ups for the data pins of SDHI0.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Stout base board support making use of 1 GiB of memory,
the Renesas H2 r8a7790 SoC with the SCIFA0 serial port
and CA15 with ARM architected timer.
Furthermore, this device tree contains entries for:
- 4x LEDs
- SDHI SD/MMC controller
- Display unit with HDMI output
- SH fast ethernet controller
- QSPI controller with S25FL512S attached to it
- I2C controller with DA9210 and DA 9063 PMICs
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
cec-clock is a fixed clock generator that is not controlled by i2c-12
and thus should not be a child of the i2c-12 bus node. Rather, it should
be a child of the root node of the DT.
Fixes: c5aa879776 ("ARM: dts: lager: Add CEC clock for HDMI transmitter")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
"debounce_interval" was never supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
DTC now warns about missing #sound-dai-cells:
/sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in
node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle
(referred from sound-dai[0])
Pass the required '#sound-dai-cells' property to fix it.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the standard 'stdout-path' property to fix the following DTC warnings:
arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dtb: Warning
(chosen_node_stdout_path): /chosen:linux,stdout-path: Use
'stdout-path' instead
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dtc now gives the following warnings:
arch/arm/boot/dts/stih410-b2120.dtb: Warning (sound_dai_property): /soc/sound/simple-audio-card,dai-link@0/codec: Missing property '#sound-dai-cells' in node /soc/sti-display-subsystem/sti-hdmi@8d04000 or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/stih407-b2120.dtb: Warning (sound_dai_property): /soc/sound/simple-audio-card,dai-link@0/codec: Missing property '#sound-dai-cells' in node /soc/sti-display-subsystem/sti-hdmi@8d04000 or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/stih410-b2260.dtb: Warning (sound_dai_property): /soc/sound/simple-audio-card,dai-link@0/codec: Missing property '#sound-dai-cells' in node /soc/sti-display-subsystem/sti-hdmi@8d04000 or bad phandle (referred from sound-dai[0])
Add the missing #sound-dai-cells property.
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
