Remove SATA from Stingray as it is unsupported.
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
BCM4908 has internal switch with 5 GPHYs. Ports 0 - 3 are always
connected to the internal PHYs. Remaining ports depend on device setup.
Asus GT-AC5300 has an extra switch with its PHYs accessible using the
internal MDIO.
CPU port and Ethernet interface remain to be documented.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This reset controller is a single register in the Broadcom's MISC block.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
BCM4908 has controller that needs different IRQ handling just like the
BCM63138. Describe it properly.
On Linux this change fixes:
brcmstb_nand ff801800.nand: timeout waiting for command 0x9
brcmstb_nand ff801800.nand: intfc status d0000000
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Netgear R8000P is home router based on BCM4906 that is a cheaper variant
of BCM4908 (e.g. 2 cores instead of 4).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already support.
This is also known as the SigmaStar SSD202D, and we add support for
the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the Ampere
Altra based "Fii Kudo" server and the Quanta GSJ, both of which are
added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last year's
generation, also added along with its reference board. This one is
still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into low-end
tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM,
and one machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board
for the aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape
LX2162A, which is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based board,
- IEI Puzzle-M801, a rackmount network appliance based on
Marvell Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm
sm8250 and sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook
(sc7180)
- New board variants of the Renesas based "Kingfisher" and
"HiHope" reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with
a few carrier boards.
There is one conflict in mt6577_auxadc.txt, which got replaced in
another tree and modified here, the modification is already part of
the new file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=R47r
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM device tree updates from Arnd Bergmann:
"Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already
support. This is also known as the SigmaStar SSD202D, and we add
support for the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the
Ampere Altra based "Fii Kudo" server and the Quanta GSJ, both of
which are added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last
year's generation, also added along with its reference board. This
one is still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into
low-end tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM, and one
machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board for the
aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape LX2162A, which
is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based
board,
- IEI Puzzle-M801, a rackmount network appliance based on Marvell
Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm sm8250 and
sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook (sc7180)
- New board variants of the Renesas based "Kingfisher" and "HiHope"
reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with a few
carrier boards"
* tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (679 commits)
arm64: dts: sparx5: Add SGPIO devices
arm64: dts: sparx5: Add reset support
dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
ARM: mstar: SMP support
ARM: mstar: Wire up smpctrl for SSD201/SSD202D
ARM: mstar: Add smp ctrl registers to infinity2m dtsi
ARM: mstar: Add dts for Honestar ssd201htv2
ARM: mstar: Add chip level dtsi for SSD202D
ARM: mstar: Add common dtsi for SSD201/SSD202D
ARM: mstar: Add infinity2m support
dt-bindings: mstar: Add Honestar SSD201_HT_V2 to mstar boards
dt-bindings: vendor-prefixes: Add honestar vendor prefix
dt-bindings: mstar: Add binding details for mstar,smpctrl
ARM: mstar: Fill in GPIO controller properties for infinity
ARM: mstar: Add gpio controller to MStar base dtsi
ARM: zynq: Fix incorrect reference to XM013 instead of XM011
ARM: zynq: Convert at25 binding to new description on zc770-xm013
ARM: zynq: Fix OCM mapping to be aligned with binding on zc702
ARM: zynq: Fix leds subnode name for zc702/zybo-z7
ARM: zynq: Rename bus to be align with simple-bus yaml
...
They don't descibe hardware fully yet but it's enough to boot a system.
Some missing blocks:
1. PMC (Power Management Controller?)
2. Ethernet
3. Crypto
4. Thermal
Asus DTS is missing defining full NAND partitions layout and buttons.
Further changes will fill those gaps as soon as required bindings will
be found / tested / added.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The scripts/dtc/checks.c requires that the node have empty "dma-ranges"
property must have the same "#address-cells" and "#size-cells" values as
the parent node. Otherwise, the following warnings is reported:
arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \
(dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \
its #address-cells (1) differs from / (2)
arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \
(dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \
its #size-cells (1) differs from / (2)
Arnd Bergmann figured out why it's necessary:
Also note that the #address-cells=<1> means that any device under
this bus is assumed to only support 32-bit addressing, and DMA will
have to go through a slow swiotlb in the absence of an IOMMU.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20201016090833.1892-2-thunder.leizhen@huawei.com'
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The string was incorrectly defined before from least to most specific,
swap the compatible strings accordingly.
Fixes: ff73917d38 ("ARM64: dts: Add QSPI Device Tree node for NS2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The SP805 binding sets the name for the actual watchdog clock to
"wdog_clk" (with an underscore).
Change the name in the DTs for Broadcom platforms to match that. The
Linux and U-Boot driver use the *first* clock for this purpose anyway,
so it does not break anything.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds a reference to the dts of the Raspberry Pi 4 B,
so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
There are total of 151 non-secure gpio (0-150) and four
pins of pinmux (91, 92, 93 and 94) are not mapped to any
gpio pin, hence update same in DT.
Fixes: 8aa428cc1e ("arm64: dts: Add pinctrl DT nodes for Stingray SOC")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.3, please pull the following:
- Pramod adds the Device Tree nodes for thermal support on Stingray
- Srinath adds the Device Tree nodes for both XHCI (host) and BDC
(device) modes
- Rayagonda adds the Device Tree node for slave I2C operation when
Stingray operates as a SmartNIC
* tag 'arm-soc/for-5.3/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: Stingray: Add NIC i2c device node
arm64: dts: Add USB DT nodes for Stingray SoC
arm64: dts: stingray: Add Stingray Thermal DT support.
Signed-off-by: Olof Johansson <olof@lixom.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DT nodes for
- Two xHCI host controllers
- Two BDC Broadcom USB device controller
- Five USB PHY controllers
[xHCI0] [BDC0] [xHCI1] [BDC1]
| | | |
--------------- -----------------------
| | | | |
[SS-PHY0] [HS-PHY0] [SS-PHY1] [HS-PHY2] [HS-PHY1]
[SS-PHY0/HS-PHY0] and [SS-PHY1/HS-PHY1] are combo PHYs has one SS and
one HS PHYs. [HS-PHY2] is a single HS PHY.
xHCI use SS-PHY to detect SS devices and HS-PHY to detect HS/FS/LS
devices. BDC use SS-PHY in SS mode and HS-PHY in HS mode.
xHCI0 port1 is SS-PHY0, port2 is HS-PHY0.
xHCI1 port1 is SS-PHY1, port2 is HS-PHY2 and port3 is HS-PHY1.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
for 5.1, please pull the following:
- Stefan adds support for the Raspberry Pi 3 A+ by using the same
mechanism of creating a symbolic reference to the ARM 32-bit DTS file
-----BEGIN PGP SIGNATURE-----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=iDFK
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.1/devicetree-arm64' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM64-based SoCs Device Tree updates
for 5.1, please pull the following:
- Stefan adds support for the Raspberry Pi 3 A+ by using the same
mechanism of creating a symbolic reference to the ARM 32-bit DTS file
* tag 'arm-soc/for-5.1/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: Add reference to RPi 3 A+
ARM: dts: add Raspberry Pi 3 A+
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds a reference to the dts of the Raspberry Pi 3 A+,
so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
The 'arm,armv8' compatible string is only for software models. It adds
little value otherwise and is inconsistently used as a fallback on some
platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Chanho Min <chanho.min@lge.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit a7eb26392b ("arm64: dts: broadcom: Add reference to Compute
Module IO Board V3") adds the bcm2837-rpi-cm3-io3.dts file as a target
in the Makefile, rather than the .dtb name. This will skip the
generation of the .dtb file at compile time and will fail the dtbs_install
target.
Fixes: a7eb26392b ("arm64: dts: broadcom: Add reference to Compute Module IO Board V3")
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dtb: Warning (i2c_bus_reg): /hsls/i2c@e0000/pcf8574@20: I2C bus unit address format error, expected "27"
arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dtb: Warning (i2c_bus_reg): /hsls/i2c@e0000/pcf8574@20: I2C bus unit address format error, expected "27"
arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dtb: Warning (spi_bus_bridge): /hsls/ssp@180000: node name for SPI buses should be 'spi'
arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dtb: Warning (spi_bus_bridge): /hsls/ssp@190000: node name for SPI buses should be 'spi'
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds a reference to the dts of the Compute Module IO Board V3 in arm,
so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN and
PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor variants
of boards/platforms.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAlt+NecPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3ScQQAIic6NPWiqGEwTRN1I+WoyoCt8oTGgiiu1kf
h23RaLWI+TaEpR1yg5ko6wGlxlvBG1C/u2sOc0lD9nSt9JQ3evXXwMQ0bUNhKdSE
8z3jhpnJYu5iNDsB15XfznhivpjOQUQNQXPR1/PG9j6SCKgdWi6wYR+A+q98Pe9d
otzMizQOY0QUMYAec20Zvzgfs+AvEtOAo/w5K4tRb+Fv/EVixV8bVeT4uykxunFt
6xOM0Ssvnwo3AnEh+V+FjAL8khMC7A3JC+/emXqqcw1Ogdg/GSnxriL7v6LchcwH
fvYb8hujQCcZ0+mlN0W214RkWd1xAc0CwJ0JdKw/RMnskty5u5B7gXcDyZFw1oJ7
b7Uof7N8l12lsXTqWW8CKOHupI1gxYshi0QJzkgkfY6P3h8ntE8HJhhcgjcHE0AN
3mMjhzbDGjfUykVgS2rFpR6tm3JHT13jDl88jhAT+xtuYYxy60nqPBM9MD6jIzjF
BnIVJBNX3sYa7aheEnZFBuA/Af/05fKbpUVQTNwnfq2f6NYDAbF9iBkCHepudZBa
0U+tNHuDlVXwLXoocE1Nac5IJgPiuX2bsuJ9xHKLXb6hMr9L4YtPOaKwDaJb1hTZ
XIHhlrF9w0ig9gu3IxaE+rC3hfu965CeFws0kwSZ9l52xmSP0Yi22ebSTfP6+h+u
XLyOhpp8
=J0qC
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Olof Johansson:
"Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board
types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN
and PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor
variants of boards/platforms"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (478 commits)
arm64: dts: sdm845: Add tsens nodes
arm64: dts: msm8996: thermal: Initialise via DT and add second controller
arm64: dts: sprd: Add one suspend timer
arm64: dts: sprd: Add SC27XX ADC device
arm64: dts: sprd: Add SC27XX eFuse device
arm64: dts: sprd: Add SC27XX vibrator device
arm64: dts: sprd: Add SC27XX breathing light controller device
arm64: dts: meson-axg: add spdif-dit codec
arm64: dts: meson-axg: add lineout codec
arm64: dts: meson-axg: add linein codec
arm64: dts: meson-axg: add tdm interfaces
arm64: dts: meson-axg: add tdmout formatters
arm64: dts: meson-axg: add tdmin formatters
arm64: dts: meson-axg: add spdifout
arm64: dts: rockchip: add led support for Firefly-RK3399
arm64: dts: rockchip: remove deprecated Type-C PHY properties on rk3399
arm64: dts: rockchip: add power button support for Firefly-RK3399
ARM: dts: aspeed: Add coprocessor interrupt controller
arm64: dts: meson-axg: add audio arb reset controller
arm64: dts: meson-axg: add usb power regulator
...
Modify the base address of the mdio mux driver to point to the
start of the mdio mux block's register address space.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for 4.19, please pull the following:
- Scott does a bunch of updates to the Stingray DTS and DTS include
files to better support the addition of new boards. Scott also adds
the Stingray OTP Device Tree node
- Pramod updates the Stingray clocks such that they match the latest
revision of the ASIC and datasheets
- Ray sets the Stingray initial watchdog timeout to 60 seconds to give
sufficient time for the kernel to boot and then adds PAXC (internal
PCIe) support to the Stingray base DTS files
- Vladimir adds support for the Stingray smart NIC PS225 boards variants
-----BEGIN PGP SIGNATURE-----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=wh6F
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.19/devicetree-arm64' of https://github.com/Broadcom/stblinux into next/dt
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 4.19, please pull the following:
- Scott does a bunch of updates to the Stingray DTS and DTS include
files to better support the addition of new boards. Scott also adds
the Stingray OTP Device Tree node
- Pramod updates the Stingray clocks such that they match the latest
revision of the ASIC and datasheets
- Ray sets the Stingray initial watchdog timeout to 60 seconds to give
sufficient time for the kernel to boot and then adds PAXC (internal
PCIe) support to the Stingray base DTS files
- Vladimir adds support for the Stingray smart NIC PS225 boards variants
* tag 'arm-soc/for-4.19/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: stingray: add bcm958802a802x dts
arm64: dts: stingray: add PAXC support
arm64: dts: set initial SR watchdog timeout to 60 seconds
arm64: dts: Update Stingray clock DT nodes
arm64: dts: stingray: Add OTP device node
arm64: dts: stingray: move common board components to stingray-board-base
Signed-off-by: Olof Johansson <olof@lixom.net>
Add bcm958802a802x dts to be used on all Stingray smart NIC PS225 board
variants
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add PAXC support to Broadcom Stingray SoC
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Peter Spreadborough <peter.spreadborough@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Set initial Stingray watchdog timeout to 60 seconds
By the time when the userspace watchdog daemon is ready and taking control
over, the watchdog timeout will then be reset to what's configured in the
daemon.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Update clock output names in the Stingray clock DT nodes so they match
the binding document and the latest ASIC datasheet. Also add entries
for LCPLL2
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Move common board components from base bcm958742 dtsi file to new
stingray-board-base dtsi file so they can be shared between many stingray
boards following common design.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
for 4.18, please pull the following:
- Stefan provides updates to the BCM2835 RNG Device Tree binding and
Device Tree node by adding its missing interrupt line.
- Rafal switches the Luxul XWC-1000 and the D-Link DIR-885L to the new
partitions syntax which allows specifying a partition parser
- Rafal also updates a bunch of BCM5301X Device Tree source files to a
more standard SPDX tag and dual GPL 2.0 and MIT. This is a follow-up
to this discussion with Greg:
https://lkml.org/lkml/2018/4/28/179
- Dan adds support for two Luxul devices: XAP-1610 (based on BCM47094)
and XWR-3150 V1 (similar to XWR-3100)
- Stefan provides a set of updates to the BCM283x Device Tree sources to
support the Raspberry Pi 3 B+ for both the ARM and ARM64 kernels. He
adds the required nodes for the LAN7515 USB Ethernet, Cypress CYW43455
BT/WiFi combo chip. Stefan also provides a few fixes for the PWM pin
assignment for RPi 3B and Zero/Zero W. Finally, Stefan adds the
missing GPIOs for controlling additional peripherals now that support
for the RPi 3 GPIO expander has landed
-----BEGIN PGP SIGNATURE-----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=R36h
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.18/devicetree' of https://github.com/Broadcom/stblinux into next/dt
This pull request contains Broadcom ARM-based SoC Device Tree changes
for 4.18, please pull the following:
- Stefan provides updates to the BCM2835 RNG Device Tree binding and
Device Tree node by adding its missing interrupt line.
- Rafal switches the Luxul XWC-1000 and the D-Link DIR-885L to the new
partitions syntax which allows specifying a partition parser
- Rafal also updates a bunch of BCM5301X Device Tree source files to a
more standard SPDX tag and dual GPL 2.0 and MIT. This is a follow-up
to this discussion with Greg:
https://lkml.org/lkml/2018/4/28/179
- Dan adds support for two Luxul devices: XAP-1610 (based on BCM47094)
and XWR-3150 V1 (similar to XWR-3100)
- Stefan provides a set of updates to the BCM283x Device Tree sources to
support the Raspberry Pi 3 B+ for both the ARM and ARM64 kernels. He
adds the required nodes for the LAN7515 USB Ethernet, Cypress CYW43455
BT/WiFi combo chip. Stefan also provides a few fixes for the PWM pin
assignment for RPi 3B and Zero/Zero W. Finally, Stefan adds the
missing GPIOs for controlling additional peripherals now that support
for the RPi 3 GPIO expander has landed
* tag 'arm-soc/for-4.18/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Switch D-Link DIR-885L to the new partitions syntax
ARM: dts: BCM5301X: Relicense Asus RT-AC87U file to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Add DT for Luxul XAP-1610
ARM: dts: BCM5301X: Add DT for Luxul XWR-3150 V1
ARM: dts: BCM5301X: Relicense Buffalo files to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Relicense most DTS files to the GPL 2.0+ / MIT
arm64: dts: broadcom: Add reference to Raspberry Pi 3 B+
ARM: dts: bcm2837: Add Raspberry Pi 3 B+
dt-bindings: bcm: Add Raspberry Pi 3 B+
ARM: dts: bcm2837: Add missing GPIOs of Expander
ARM: dts: bcm283x: Fix PWM pin assignment
ARM: dts: BCM5301X: Switch Luxul XWC-1000 to the new fixed partitions syntax
ARM: bcm283x: Add missing interrupt for RNG block
dt-binding: rng: Add interrupt property for BCM2835
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds a reference to the dts of the Raspberry Pi 3 B+
in arm, so don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Correct all SATA ahci and phy controller register
addresses and interrupt lines to proper values.
Fixes: 344a2e5141 ("arm64: dts: Add SATA DT nodes for Stingray SoC")
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Andrew Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We add device tree files for a couple of additional SoCs in various areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for networking,
Amlogic A113D for audio, and Renesas R-Car V3M for automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX, Amlogic
and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues that
the latest version of 'dtc' now warns about. Unfortunately there is still
a lot left to do.
A rework of the ARM foundation model introduced several new files
for common variations of the model.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TnSo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional SoCs in various
areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for
networking, Amlogic A113D for audio, and Renesas R-Car V3M for
automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX,
Amlogic and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues
that the latest version of 'dtc' now warns about. Unfortunately there
is still a lot left to do.
A rework of the ARM foundation model introduced several new files for
common variations of the model"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits)
arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3
dt-bindings: bus: Add documentation for the Technologic Systems NBUS
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
...
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----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=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.
Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.
One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.
Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.
As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>
We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.
Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
