Adds a trace function used in brcmf_dbg_hex_dump() which adds the
raw binary data to the trace. It requires trace-cmd plugin to see
this data.
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upon receiving an IF event from the firmware the interface
was created and stored on a list using the interface index.
With upcoming P2P feature the firmware will send a IF event
in which two interfaces have the same interface index. To
uniquely locate them on the list the bss index is now used.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The call to brcmf_dbg(ERROR, ...) only resulted in a log message
when compiled with -DDEBUG. Error messages are valuable for resolving
issues so this patch replaces it with brcmf_err(...) so they always
end up in the log.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removing obsolete functions and prototypes. Moving (and renaming)
defines to place with similar definitions. Removing unnecessary
includes.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When debug is turned on for fwil then the whole data buffer is
dumped. In some cases this gives excessive amount of debug. With
this patch the dumps are limited to 64 bytes.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmf_netdev_start_xmit and brcmf_fil_cmd_data are checking
bus state for down. These functions should check for data
state.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_fil_bsscfg_data_get() calls brcmf_create_iovar()
with data pointer set to NULL, which caused a NULL pointer access.
As it should be possible to provide data in message towards the
firmware, it should just pass the data buffer instead.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions for communicating were given the net_device only because
its private data contained struct brcmf_if object. However, not all
firmware related interfaces will be associated with a net_device. To
accomodate provisioning firmware for such interfaces the struct
brcmf_if object will be passed to the fwil functions.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware interface has functions to send bsscfg specific commands
to the device. These functions currently have a bssidx parameter, but
that same information is stored in struct brcmf_if, which is in the
private data of the net_device parameter.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refactor the functions that are related to getting and setting
data to and and from the firmware.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
