One of the easiest way to test config with 4K HPTE is to disable 64K hardware
page size like below.
int __init htab_dt_scan_page_sizes(unsigned long node,
size -= 3; prop += 3;
base_idx = get_idx_from_shift(base_shift);
- if (base_idx < 0) {
+ if (base_idx < 0 || base_idx == MMU_PAGE_64K) {
/* skip the pte encoding also */
prop += lpnum * 2; size -= lpnum * 2;
But then this results in error in other part of the code such as MPSS parsing
where we look at 4K base page size and 64K actual page size support.
This patch fix MPSS parsing by ignoring the actual page sizes marked
unsupported. In reality this can happen only with a corrupt device tree. But it
is good to tighten the error check.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge our fixes branch from the 4.15 cycle.
Unusually the fixes branch saw some significant features merged,
notably the RFI flush patches, so we want the code in next to be
tested against that, to avoid any surprises when the two are merged.
There's also some other work on the panic handling that was reverted
in fixes and we now want to do properly in next, which would conflict.
And we also fix a few other minor merge conflicts.
Radix enabled platforms don't support subpage_prot() system calls. But
at present the system call goes through without an error and fails
later on while validating expected subpage accesses. Lets not allow
the system call on powerpc radix platforms to begin with to prevent
this confusion in user space.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PAPR defines 'ibm,processor-storage-keys' property. It exports two
values. The first value holds the number of data-access keys and the
second holds the number of instruction-access keys. Due to a bug in
the firmware, instruction-access keys is always reported as zero.
However any key can be configured to disable data-access and/or
disable execution-access. The inavailablity of the second value is not
a big handicap, though it could have been used to determine if the
platform supported disable-execution-access.
Non-PAPR platforms do not define this property in the device tree yet.
Fortunately power8 is the only released Non-PAPR platform that is
supported. Here, we hardcode the number of supported pkey to 32, by
consulting the PowerISA3.0
This patch calculates the number of keys supported by the platform.
Also it determines the platform support for read/write/execution
access support for pkeys.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
[mpe: Use a PVR check instead of CPU_FTR for execute. Restrict to
Power7/8/9 for now until older CPUs are tested.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The value of the pkey, whose protection got violated,
is made available in si_pkey field of the siginfo structure.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
get_mm_addr_key() helper returns the pkey associated with
an address corresponding to a given mm_struct.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Handle Data and Instruction exceptions caused by memory
protection-key.
The CPU will detect the key fault if the HPTE is already
programmed with the key.
However if the HPTE is not hashed, a key fault will not
be detected by the hardware. The software will detect
pkey violation in such a case.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch provides the implementation for
arch_vma_access_permitted(). Returns true if the
requested access is allowed by pkey associated with the
vma.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
helper function that checks if the read/write/execute is allowed
on the pte.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Map the PTE protection key bits to the HPTE key protection bits,
while creating HPTE entries.
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
arch independent code calls arch_override_mprotect_pkey()
to return a pkey that best matches the requested protection.
This patch provides the implementation.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
arch-independent code expects the arch to map
a pkey into the vma's protection bit setting.
The patch provides that ability.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch provides the implementation of execute-only pkey.
The architecture-independent layer expects the arch-dependent
layer, to support the ability to create and enable a special
key which has execute-only permission.
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Store and restore the AMR, IAMR and UAMOR register state of the task
before scheduling out and after scheduling in, respectively.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc has hardware support to disable execute on a pkey.
This patch enables the ability to create execute-disabled
keys.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch provides the detailed implementation for
a user to allocate a key and enable it in the hardware.
It provides the plumbing, but it cannot be used till
the system call is implemented. The next patch will
do so.
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Introduce helper functions that can initialize the bits in the AMR,
IAMR and UAMOR register; the bits that correspond to the given pkey.
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Implements helper functions to read and write the key related
registers; AMR, IAMR, UAMOR.
AMR register tracks the read,write permission of a key
IAMR register tracks the execute permission of a key
UAMOR register enables and disables a key
Acked-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Total 32 keys are available on power7 and above. However
pkey 0,1 are reserved. So effectively we have 30 pkeys.
On 4K kernels, we do not have 5 bits in the PTE to
represent all the keys; we only have 3bits. Two of those
keys are reserved; pkey 0 and pkey 1. So effectively we
have 6 pkeys.
This patch keeps track of reserved keys, allocated keys
and keys that are currently free.
Also it adds skeletal functions and macros, that the
architecture-independent code expects to be available.
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Basic plumbing to initialize the pkey system.
Nothing is enabled yet. A later patch will enable it
once all the infrastructure is in place.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
[mpe: Rework copyrights to use SPDX tags]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rename the paca->soft_enabled to paca->irq_soft_mask as it is no
longer used as a flag for interrupt state, but a mask.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Two #defines IRQS_ENABLED and IRQS_DISABLED are added to be used when
updating paca->soft_enabled. Replace the hardcoded values used when
updating paca->soft_enabled with IRQ_(EN|DIS)ABLED #define. No logic
change.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the previous patch to switch to 64-bit mode after returning from
RTAS and before doing any memory accesses, the RMA limit need not be
clamped to 1GB to avoid RTAS bugs.
Keep the 1GB limit for older firmware (although this is more of a kernel
concern than RTAS), and remove it starting with POWER9.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the previous patch to switch to 64-bit mode after returning from
RTAS and before doing any memory accesses, the RMA limit need not be
clamped to 1GB to avoid RTAS bugs.
Keep the 1GB limit for older firmware (although this is more of a kernel
concern than RTAS), and remove it starting with POWER9.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The radix guest is not subject to the paravirtualized HPT VRMA limit,
so remove that from ppc64_rma_size calculation for that platform.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This removes the RMA limit on powernv platform, which constrains
early allocations such as PACAs and stacks. There are still other
restrictions that must be followed, such as bolted SLB limits, but
real mode addressing has no constraints.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are several cases outside the normal address space management
where a CPU's entire local TLB is to be flushed:
1. Booting the kernel, in case something has left stale entries in
the TLB (e.g., kexec).
2. Machine check, to clean corrupted TLB entries.
One other place where the TLB is flushed, is waking from deep idle
states. The flush is a side-effect of calling ->cpu_restore with the
intention of re-setting various SPRs. The flush itself is unnecessary
because in the first case, the TLB should not acquire new corrupted
TLB entries as part of sleep/wake (though they may be lost).
This type of TLB flush is coded inflexibly, several times for each CPU
type, and they have a number of problems with ISA v3.0B:
- The current radix mode of the MMU is not taken into account, it is
always done as a hash flushn For IS=2 (LPID-matching flush from host)
and IS=3 with HV=0 (guest kernel flush), tlbie(l) is undefined if
the R field does not match the current radix mode.
- ISA v3.0B hash must flush the partition and process table caches as
well.
- ISA v3.0B radix must flush partition and process scoped translations,
partition and process table caches, and also the page walk cache.
So consolidate the flushing code and implement it in C and inline asm
under the mm/ directory with the rest of the flush code. Add ISA v3.0B
cases for radix and hash, and use the radix flush in radix environment.
Provide a way for IS=2 (LPID flush) to specify the radix mode of the
partition. Have KVM pass in the radix mode of the guest.
Take out the flushes from early cputable/dt_cpu_ftrs detection hooks,
and move it later in the boot process after, the MMU registers are set
up and before relocation is first turned on.
The TLB flush is no longer called when restoring from deep idle states.
This was not be done as a separate step because booting secondaries
uses the same cpu_restore as idle restore, which needs the TLB flush.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Trap numbers can have extra bits at the bottom that need to
be filtered out. There are a few cases where we don't do that.
It's possible that we got lucky but better safe than sorry.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When CONFIG_SWAP is set, the TLB miss handlers have to also take
into account _PAGE_ACCESSED flag. At the moment it is done by
anding _PAGE_ACCESSED into _PAGE_PRESENT using 3 instructions.
This patch uses APG for handling _PAGE_ACCESSED, allowing to
just copy _PAGE_ACCESSED bit into APG field, hence reducing the
action to a single instruction.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As Linux kernel separates KERNEL and USER address spaces, there is
therefore no need to flag USER access at page level.
Today, the 8xx TLB handlers already handle user access in the L1 entry
through Access Protection Groups, it is then natural to move the user
access handling at PMD level once _PAGE_NA allows to handle PAGE_NONE
protection without _PAGE_USER
In the mean time, as we free up one bit in the PTE, we can use it to
include SPS (page size flag) in the PTE and avoid handling it at every
TLB miss hence removing special handling based on compiled page size.
For _PAGE_EXEC, we rework it to use PP PTE bits, avoiding the copy
of _PAGE_EXEC bit into the L1 entry. Unfortunatly we are not
able to put it at the correct location as it conflicts with
NA/RO/RW bits for data entries.
Upper bits of APG in L1 entry overlap with PMD base address. In
order to avoid having to filter that out, we set up all groups so that
upper bits can have any value.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Today, PAGE_NONE is defined as a page not having _PAGE_USER.
In some circunstances, when the CPU supports it, it might be
better to be able to flag a page with NO ACCESS.
In a following patch, the 8xx will switch user access being flagged
in the PMD, therefore it will not be possible anymore to use
_PAGE_USER as a way to flag a page with no access.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
commit ac29c64089 ("powerpc/mm: Replace _PAGE_USER with
_PAGE_PRIVILEGED") introduced _PAGE_PRIVILEGED for BOOK3S/64
This patch generalises _PAGE_PRIVILEGED for all CPUs, allowing
to have either _PAGE_PRIVILEGED or _PAGE_USER or both.
PPC_8xx has a _PAGE_SHARED flag which is set for and only for
all non user pages. Lets rename it _PAGE_PRIVILEGED to remove
confusion as it has nothing to do with Linux shared pages.
On BookE, there's a _PAGE_BAP_SR which has to be set for kernel
pages: defining _PAGE_PRIVILEGED as _PAGE_BAP_SR will make
this generic
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Power Hypervisor has introduced a new device tree format for
the property describing the dynamic reconfiguration LMBs for a system,
ibm,dynamic-memory-v2. This new format condenses the size of the
property, especially on large memory systems, by reporting sets
of LMBs that have the same properties (flags and associativity array
index).
This patch updates the powerpc/mm/drmem.c code to provide routines
that can parse the new device tree format during the walk_drmem_lmb*
routines used during boot, the creation of the LMB array, and updating
the device tree to create a new property in the proper format for
ibm,dynamic-memory-v2.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that the powerpc code parses dynamic reconfiguration memory
LMB information from the LMB array and not the device tree
directly we can move the of_drconf_cell struct to drmem.h where
it fits better.
In addition, the struct is renamed to of_drconf_cell_v1 in
anticipation of upcoming support for version 2 of the dynamic
reconfiguration property and the members are typed as __be*
values to reflect how they exist in the device tree.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Update the pseries memory hotplug code to use the newly added
dynamic reconfiguration LMB array. Doing this is required for the
upcoming support of version 2 of the dynamic reconfiguration
device tree property.
In addition, making this change cleans up the code that parses the
LMB information as we no longer need to worry about device tree
format. This allows us to discard one of the first steps on memory
hotplug where we make a working copy of the device tree property and
convert the entire property to cpu format. Instead we just use the
LMB array directly while holding the memory hotplug lock.
This patch also moves the updating of the device tree property to
powerpc/mm/drmem.c. This allows to the hotplug code to work without
needing to know the device tree format and provides a single
routine for updating the device tree property. This new routine
will handle determination of the proper device tree format and
generate a properly formatted device tree property.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Update code in powerpc/numa.c to use the walk_drmem_lmbs()
routine instead of parsing the device tree directly. This is
in anticipation of introducing a new ibm,dynamic-memory-v2
property with a different format. This will allow the numa code
to use a single initialization routine per-LMB irregardless of
the device tree format.
Additionally, to support additional routines in numa.c that need
to look up LMB information, an late_init routine is added to drmem.c
to allocate the array of LMB information. This LMB array will provide
per-LMB information to separate the LMB data from the device tree
format.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We currently have code to parse the dynamic reconfiguration LMB
information from the ibm,dynamic-meory device tree property in
multiple locations; numa.c, prom.c, and pseries/hotplug-memory.c.
In anticipation of adding support for a version 2 of the
ibm,dynamic-memory property this patch aims to separate the device
tree information from the device tree format.
Doing this requires a two step process to avoid a possibly very large
bootmem allocation early in boot. During initial boot, new routines
are provided to walk the device tree property and make a call-back
for each LMB.
The second step (introduced in later patches) will allocate an
array of LMB information that can be used directly without needing
to know the DT format.
This approach provides the benefit of consolidating the device tree
property parsing to a single location and (eventually) providing
a common data structure for retrieving LMB information.
This patch introduces a routine to walk the ibm,dynamic-memory
property in the flattened device tree and updates the prom.c code
to use this to initialize memory.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Look up the associativity arrays in of_drconf_to_nid_single when
deriving the nid for a LMB instead of having it passed in as a
parameter.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Look up the device node for the usable memory property instead
of having it passed in as a parameter. This changes precedes an update
in which the calling routines for of_get_usable_memory() will not have
the device node pointer to pass in.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Look up the device node for the associativity array property instead
of having it passed in as a parameter. This changes precedes an update
in which the calling routines for of_get_assoc_arrays() will not have
the device node pointer to pass in.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No functional changes, just untangling the call chain and document
why the altmap is passed around the hotplug code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We can just pass this on instead of having to do a radix tree lookup
without proper locking a few levels into the callchain.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We can just pass this on instead of having to do a radix tree lookup
without proper locking 2 levels into the callchain.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We can just pass this on instead of having to do a radix tree lookup
without proper locking a few levels into the callchain.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We can just pass this on instead of having to do a radix tree lookup
without proper locking 2 levels into the callchain.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
No functional change in this patch. This update gup_hugepte to use the
helper. This will help later when we add memory keys.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The H_PAGE_F_SECOND,H_PAGE_F_GIX are not in the 64K main-PTE.
capture these changes in the dump pte report.
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
replace redundant code in __hash_page_4K() and flush_hash_page()
with helper functions pte_get_hash_gslot() and pte_set_hidx()
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rearrange 64K PTE bits to free up bits 3, 4, 5 and 6
in the 64K backed HPTE pages. This along with the earlier
patch will entirely free up the four bits from 64K PTE.
The bit numbers are big-endian as defined in the ISA3.0
This patch does the following change to 64K PTE backed
by 64K HPTE.
H_PAGE_F_SECOND (S) which occupied bit 4 moves to the
second part of the pte to bit 60.
H_PAGE_F_GIX (G,I,X) which occupied bit 5, 6 and 7 also
moves to the second part of the pte to bit 61,
62, 63, 64 respectively
since bit 7 is now freed up, we move H_PAGE_BUSY (B) from
bit 9 to bit 7.
The second part of the PTE will hold
(H_PAGE_F_SECOND|H_PAGE_F_GIX) at bit 60,61,62,63.
NOTE: None of the bits in the secondary PTE were not used
by 64k-HPTE backed PTE.
Before the patch, the 64K HPTE backed 64k PTE format was
as follows
0 1 2 3 4 5 6 7 8 9 10...........................63
: : : : : : : : : : : :
v v v v v v v v v v v v
,-,-,-,-,--,--,--,--,-,-,-,-,-,------------------,-,-,-,
|x|x|x| |S |G |I |X |x|B| |x|x|................|x|x|x|x| <- primary pte
'_'_'_'_'__'__'__'__'_'_'_'_'_'________________'_'_'_'_'
| | | | | | | | | | | | |..................| | | | | <- secondary pte
'_'_'_'_'__'__'__'__'_'_'_'_'__________________'_'_'_'_'
After the patch, the 64k HPTE backed 64k PTE format is
as follows
0 1 2 3 4 5 6 7 8 9 10...........................63
: : : : : : : : : : : :
v v v v v v v v v v v v
,-,-,-,-,--,--,--,--,-,-,-,-,-,------------------,-,-,-,
|x|x|x| | | | |B |x| | |x|x|................|.|.|.|.| <- primary pte
'_'_'_'_'__'__'__'__'_'_'_'_'_'________________'_'_'_'_'
| | | | | | | | | | | | |..................|S|G|I|X| <- secondary pte
'_'_'_'_'__'__'__'__'_'_'_'_'__________________'_'_'_'_'
The above PTE changes is applicable to hugetlbpages aswell.
The patch does the following code changes:
a) moves the H_PAGE_F_SECOND and H_PAGE_F_GIX to 4k PTE
header since it is no more needed b the 64k PTEs.
b) abstracts out __real_pte() and __rpte_to_hidx() so the
caller need not know the bit location of the slot.
c) moves the slot bits to the secondary pte.
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
