This is a non-functional change, it simplifies multiple access to
'struct device' pointer derived from a platform device pointer,
the new local variable will also be used in the following changes.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace GPLv2 header with the SPDX identifier.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The error cases of mediatek_gpio_bank_probe() would go unnoticed (except
for the dev_err() messages). The probe function should return an error
if one of the banks failed to initialize properly indicated by
not returning non-0.
Fixes: 4ba9c3afda ("gpio: mt7621: Add a driver for MT7621")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kasprintf() may return NULL on failure of internal allocation thus the
assigned label is not safe if not explicitly checked. On error
mediatek_gpio_bank_probe() returns negative values so -ENOMEM in the
(unlikely) failure case should be fine here.
Fixes: 4ba9c3afda ("gpio: mt7621: Add a driver for MT7621")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change simplifies dereferences to the mediated struct device, also
it allows to limit the scope of the platform device usage to probe and
remove functions only.
Non-functional change.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This simplifies and standardizes the AB IRQ handler by using
the for_each_set_bit() library function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Convert the legacy system PM callbacks to new ones. Meanwhile, remove the
redundant calls to the PCI for changing a power state since it's done by bus
code.
While here, remove weird indentation with backslash in use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Volume is a little higher than usual due to a set of gpio fixes for
Davinci platforms that's been around a while, still seemed appropriate
to not hold off until next merge window.
Besides that it's the usual mix of minor fixes, mostly corrections of
small stuff in device trees.
Major stability-related one is the removal of a regulator from DT on
Rock960, since DVFS caused undervoltage. I expect it'll be restored once
they figure out the underlying issue.
-----BEGIN PGP SIGNATURE-----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=m41T
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Volume is a little higher than usual due to a set of gpio fixes for
Davinci platforms that's been around a while, still seemed appropriate
to not hold off until next merge window.
Besides that it's the usual mix of minor fixes, mostly corrections of
small stuff in device trees.
Major stability-related one is the removal of a regulator from DT on
Rock960, since DVFS caused undervoltage. I expect it'll be restored
once they figure out the underlying issue"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
MAINTAINERS: Remove unused Qualcomm SoC mailing list
ARM: davinci: dm644x: set the GPIO base to 0
ARM: davinci: da830: set the GPIO base to 0
ARM: davinci: dm355: set the GPIO base to 0
ARM: davinci: dm646x: set the GPIO base to 0
ARM: davinci: dm365: set the GPIO base to 0
ARM: davinci: da850: set the GPIO base to 0
gpio: davinci: restore a way to manually specify the GPIO base
ARM: davinci: dm644x: define gpio interrupts as separate resources
ARM: davinci: dm355: define gpio interrupts as separate resources
ARM: davinci: dm646x: define gpio interrupts as separate resources
ARM: davinci: dm365: define gpio interrupts as separate resources
ARM: davinci: da8xx: define gpio interrupts as separate resources
ARM: dts: at91: sama5d2: use the divided clock for SMC
ARM: dts: imx51-zii-rdu1: Remove EEPROM node
ARM: dts: rockchip: Remove @0 from the veyron memory node
arm64: dts: rockchip: Fix PCIe reset polarity for rk3399-puma-haikou.
arm64: dts: qcom: msm8998: Reserve gpio ranges on MTP
arm64: dts: sdm845-mtp: Reserve reserved gpios
arm64: dts: ti: k3-am654: Fix wakeup_uart reg address
...
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When retrieveing CD (card detect) and WP (write protect)
GPIO handles from the device tree, make sure to assign
them active low by default unless the "cd-inverted" or
"wp-inverted" properties are set. These properties mean
that respective signal is active HIGH since the SDHCI
specification stipulates that this kind of signals
should be treated as active LOW.
If the twocell GPIO flag is also specified as active
low, well that's nice and we will silently ignore the
tautological specification.
If however the GPIO line is specified as active low
in the GPIO flasg cell and "cd-inverted" or "wp-inverted"
is also specified, the latter takes precedence and we
print a warning.
The current effect on the MMC slot-gpio core are as
follows:
For CD GPIOs: no effect. The current code in
mmc/core/host.c calls mmc_gpiod_request_cd() with
the "override_active_level" argument set to true,
which means that whatever the GPIO descriptor
thinks about active low/high will be ignored, the
core will use the MMC_CAP2_CD_ACTIVE_HIGH to keep
track of this and reads the raw value from the
GPIO descriptor, totally bypassing gpiolibs inversion
semantics. I plan to clean this up at a later point
passing the handling of inversion semantics over
to gpiolib, so this patch prepares the ground for
that.
Fow WP GPIOs: this is probably fixing a bug, because
the code in mmc/core/host.c calls mmc_gpiod_request_ro()
with the "override_active_level" argument set to false,
which means it will respect the inversion semantics of
the gpiolib and ignore the MMC_CAP2_RO_ACTIVE_HIGH
flag for everyone using this through device tree.
However the code in host.c confusingly goes to great
lengths setting up the MMC_CAP2_RO_ACTIVE_HIGH flag
from the GPIO descriptor and by reading the "wp-inverted"
property of the node. As far as I can tell this is all
in vain and the inversion is broken: device trees that
use "wp-inverted" do not work as intended, instead the
only way to actually get inversion on a line is by
setting the second cell flag to GPIO_ACTIVE_HIGH (which
will be the default) or GPIO_ACTIVE_LOW if they want
the proper MMC semantics. Presumably all device trees do
this right but we need to parse and handle this properly.
Cc: linux-mmc@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 587f7a694f ("gpio: davinci: Use dev name for label and
automatic base selection") broke the network support in legacy boot
mode for da850-evm since we can no longer request the MDIO clock GPIO.
Other boards may be broken too, which I haven't tested.
The problem is in the fact that most board files still use the legacy
GPIO API where lines are requested by numbers rather than descriptors.
While this should be fixed eventually, in order to unbreak the board
for now - provide a way to manually specify the GPIO base in platform
data.
Fixes: 587f7a694f ("gpio: davinci: Use dev name for label and automatic base selection")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
It's easy to verify that the change of drivers/gpio/gpiolib-of.c license
header to SPDX standard changes the license from GPLv2+ to GPLv2, and
this change corrects it.
Fixes: dae5f0afcf ("gpio: Use SPDX header for core library")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove linux/gpio/driver.h which is included more than once
Signed-off-by: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some SoCs need the gpio clock to be enabled before accessing
HW registers. This patch add the optional clock handling.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 3edfb7bd76 ("gpiolib: Show correct direction from the
beginning") fixed an existing issue but broke libgpiod tests by
changing the default direction of dummy lines to output.
We don't break user-space so make gpio-mockup behave as before.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As pointed out by Gregor, spitz keyboard matrix is broken, with or
without CONFIG_PINCTRL set, quoting :
"The gpio matrix keypard on the Zaurus C3x00 (see spitz.c) does not work
properly. Noticeable are that rshift+c does nothing where as lshift+c
creates C. Opposite it is for rshift+a vs lshift+a, here only rshift
works. This affects a few other combinations using the rshift or lshift
buttons."
As a matter of fact, as for platform_data based builds CONFIG_PINCTRL=n
is required for now (as opposed for devicetree builds where it should be
set), this means gpio driver should change the direction, which is what
was attempted by commit c4e5ffb6f2 ("gpio: pxa: fix legacy non pinctrl
aware builds").
Unfortunately, the input case was inverted, and the direction change was
never done. This wasn't seen up until now because the initial platform
setup (MFP) was setting this direction. Yet in Gregory's case, the
matrix-keypad driver changes back and forth the direction dynamically,
and this is why he's the first to report it.
Fixes: c4e5ffb6f2 ("gpio: pxa: fix legacy non pinctrl aware builds")
Tested-by: Greg <greguu@null.net>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During noirq suspend/resume phase, GPIO irq could arrive
and its registers like IMR will be changed by irq handle
process, to make the GPIO registers exactly when it is
powered ON after resume, move the GPIO noirq suspend/resume
callback to syscore suspend/resume phase, local irq is
disabled at this phase so GPIO registers are atomic.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 48207d7595 ("gpio: drop devm_gpiochip_remove()") dropped the
last user of drop devm_gpio_chip_match(), causing a defined but not used
compilation warning. Fix it by removing the function.
Fixes: 48207d7595 ("gpio: drop devm_gpiochip_remove()")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change corrects the error path in gpiochip_add_data_with_key()
by avoiding to call ida_simple_remove(), if ida_simple_get() returns
an error.
Note that ida_simple_remove()/ida_free() throws a BUG(), if id argument
is negative, it allows to easily check the correctness of the fix by
fuzzing the return value from ida_simple_get().
Fixes: ff2b135922 ("gpio: make the gpiochip a real device")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiod_request_commit() copies the pointer to the label passed as
an argument only to be used later. But there's a chance the caller
could immediately free the passed string(e.g., local variable).
This could trigger a use after free when we use gpio label(e.g.,
gpiochip_unlock_as_irq(), gpiochip_is_requested()).
To be on the safe side: duplicate the string with kstrdup_const()
so that if an unaware user passes an address to a stack-allocated
buffer, we won't get the arbitrary label.
Also fix gpiod_set_consumer_name().
Signed-off-by: Muchun Song <smuchun@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Trivial fix to clean up an indentation issue, remove space
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Keeping the irq_chip definition static will make it shared with multiple
giochips in the system. This practice is considered to be bad and now we
will get the below warning from gpiolib core:
"detected irqchip that is shared with multiple gpiochips: please fix the
driver."
Hence, move the irq_chip definition from static to `struct pl061` for
using a unique irq_chip for each gpiochip.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is hardly any reason to call devm_gpiochip_remove() because the
driver core handles calling gpiochip_remove() automatically.
To make it harder to introduce new (and probably unneeded) callers, drop
the function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With a new subsystem co-maintainer on board it is good to draw
up the ongoing changes and future plans for the subsystem, i.e.
what is in my head and being worked on long term.
What better way is there than simply adding a TODO right in the
code and send it out to the mailing list.
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
There were no significant changes to the core this time!
New drivers:
- Broadcom Northstar pin control driver.
- Mediatek MT8183 subdriver.
- Mediatek MT7623 subdriver.
- Mediatek MT6765 subdriver.
- Meson g12a subdriver.
- Nuvoton NPCM7xx pin control and GPIO driver.
- Qualcomm QCS404 pin control and GPIO subdriver.
- Qualcomm SDM660 pin control and GPIO subdriver.
- Renesas R8A7744 PFC subdriver.
- Renesas R8A774C0 PFC subdriver.
- Renesas RZ/N1 pinctrl driver
Major improvements:
- Pulled the GPIO support for Ingenic over from the GPIO
subsystem and consolidated it all in the Ingenic pin control
driver.
- Major cleanups and consolidation work in all Intel drivers.
- Major cleanups and consolidation work in all Mediatek drivers.
- Lots of incremental improvements to the Renesas PFC pin
controller family.
- All drivers doing GPIO now include <linux/gpio/driver.h> and
nothing else.
-----BEGIN PGP SIGNATURE-----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=rBtH
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.20 series:
There were no significant changes to the core this time! Bur the new
Qualcomm, Mediatek and Broadcom drivers are quite interesting as they
will be used in a few million embedded devices the coming years as it
seems.
New drivers:
- Broadcom Northstar pin control driver.
- Mediatek MT8183 subdriver.
- Mediatek MT7623 subdriver.
- Mediatek MT6765 subdriver.
- Meson g12a subdriver.
- Nuvoton NPCM7xx pin control and GPIO driver.
- Qualcomm QCS404 pin control and GPIO subdriver.
- Qualcomm SDM660 pin control and GPIO subdriver.
- Renesas R8A7744 PFC subdriver.
- Renesas R8A774C0 PFC subdriver.
- Renesas RZ/N1 pinctrl driver
Major improvements:
- Pulled the GPIO support for Ingenic over from the GPIO subsystem
and consolidated it all in the Ingenic pin control driver.
- Major cleanups and consolidation work in all Intel drivers.
- Major cleanups and consolidation work in all Mediatek drivers.
- Lots of incremental improvements to the Renesas PFC pin controller
family.
- All drivers doing GPIO now include <linux/gpio/driver.h> and
nothing else"
* tag 'pinctrl-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (153 commits)
pinctrl: sunxi: Fix a memory leak in 'sunxi_pinctrl_build_state()'
gpio: uniphier: include <linux/bits.h> instead of <linux/bitops.h>
pinctrl: uniphier: include <linux/bits.h> instead of <linux/bitops.h>
dt-bindings: pinctrl: bcm4708-pinmux: improve example binding
pinctrl: geminilake: Sort register offsets by value
pinctrl: geminilake: Get rid of unneeded ->probe() stub
pinctrl: geminilake: Update pin list for B0 stepping
pinctrl: renesas: Fix platform_no_drv_owner.cocci warnings
pinctrl: mediatek: Make eint_m u16
pinctrl: bcm: ns: Use uintptr_t for casting data
pinctrl: madera: Fix uninitialized variable bug in madera_mux_set_mux
pinctrl: gemini: Fix up TVC clock group
pinctrl: gemini: Drop noisy debug prints
pinctrl: gemini: Mask and set properly
pinctrl: mediatek: select GPIOLIB
pinctrl: rza1: don't manually release devm managed resources
MAINTAINERS: update entry for Mediatek pin controller
pinctrl: bcm: add Northstar driver
dt-bindings: pinctrl: document Broadcom Northstar pin mux controller
pinctrl: qcom: fix 'const' pointer handling
...
The reason of including <linux/bitops.h> here is just for BIT() and
GENMASK macros.
Since commit 8bd9cb51da ("locking/atomics, asm-generic: Move some
macros from <linux/bitops.h> to a new <linux/bits.h> file"),
<linux/bits.h> is enough for such compile-time macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This doesn't support nested anymore, so drivers shouldn't call it with
the handler set to NULL.
Cc: Evan Green <evgreen@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This argument hasn't ever been used since it was introduced in commit
1425052097 ("gpio: add IRQ chip helpers in gpiolib"). Let's drop it to
reduce reading confusion.
Cc: Evan Green <evgreen@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We want to set the irq parent for interrupts that we're setting up to be
cascaded from another interrupt controller, but we may or may not have
already mapped the gpiochip irqs into the kernel's virtual irq number
space at this point. If we have mapped irqs before calling here, then
we've gone through gpiochip_irq_map() and called irq_set_parent()
already. If we haven't mapped irqs, then the gpiochip is dynamically
mapping irqs and we can rely on gpiochip_irq_map() or the gpio driver's
irqdomain ops to setup the irq parent properly.
Either way, setting the parent here when cascading the gpiochip doesn't
make much sense because it should be done at irq mapping time. In the
dynamic mapping case, this code is mapping virq 0 to some parent virq in
a loop. While that's benign, let's drop this code to simplify.
Cc: Evan Green <evgreen@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix kconfig warning for GPIO_SNPS_CREG:
WARNING: unmet direct dependencies detected for OF_GPIO
Depends on [n]: GPIOLIB [=y] && OF [=n] && HAS_IOMEM [=y]
Selected by [y]:
- GPIO_SNPS_CREG [=y] && GPIOLIB [=y] && HAS_IOMEM [=y] && (ARC || COMPILE_TEST [=y])
Drivers in drivers/gpio/Kconfig depend on OF_GPIO, not select it.
This prevents attempting to build when OF is not enabled.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows nonexclusive (simultaneous) access to a single
GPIO line for the fixed regulator enable line. This happens
when several regulators use the same GPIO for enabling and
disabling a regulator, and all need a handle on their GPIO
descriptor.
This solution with a special flag is not entirely elegant
and should ideally be replaced by something more careful as
this makes it possible for several consumers to
enable/disable the same GPIO line to the left and right
without any consistency. The current use inside the regulator
core should however be fine as it takes special care to
handle this.
For the state of the GPIO backend, this is still the
lesser evil compared to going back to global GPIO
numbers.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Fixes: efdfeb079c ("regulator: fixed: Convert to use GPIO descriptor only")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
gpio_hog depends on gdev field being initialized. This patch fixes an
OOPs during initialization of TI's AM335x-ICEv2.
Fixes: 3edfb7bd76 ("gpiolib: Show correct direction from the beginning")
Tested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_set_cascaded_irqchip() is passed 'parent_irq' as an argument
and then the address of that argument is assigned to the gpio chips
gpio_irq_chip 'parents' pointer shortly thereafter. This can't ever
work, because we've just assigned some stack address to a pointer that
we plan to dereference later in gpiochip_irq_map(). I ran into this
issue with the KASAN report below when gpiochip_irq_map() tried to setup
the parent irq with a total junk pointer for the 'parents' array.
BUG: KASAN: stack-out-of-bounds in gpiochip_irq_map+0x228/0x248
Read of size 4 at addr ffffffc0dde472e0 by task swapper/0/1
CPU: 7 PID: 1 Comm: swapper/0 Not tainted 4.14.72 #34
Call trace:
[<ffffff9008093638>] dump_backtrace+0x0/0x718
[<ffffff9008093da4>] show_stack+0x20/0x2c
[<ffffff90096b9224>] __dump_stack+0x20/0x28
[<ffffff90096b91c8>] dump_stack+0x80/0xbc
[<ffffff900845a350>] print_address_description+0x70/0x238
[<ffffff900845a8e4>] kasan_report+0x1cc/0x260
[<ffffff900845aa14>] __asan_report_load4_noabort+0x2c/0x38
[<ffffff900897e098>] gpiochip_irq_map+0x228/0x248
[<ffffff900820cc08>] irq_domain_associate+0x114/0x2ec
[<ffffff900820d13c>] irq_create_mapping+0x120/0x234
[<ffffff900820da78>] irq_create_fwspec_mapping+0x4c8/0x88c
[<ffffff900820e2d8>] irq_create_of_mapping+0x180/0x210
[<ffffff900917114c>] of_irq_get+0x138/0x198
[<ffffff9008dc70ac>] spi_drv_probe+0x94/0x178
[<ffffff9008ca5168>] driver_probe_device+0x51c/0x824
[<ffffff9008ca6538>] __device_attach_driver+0x148/0x20c
[<ffffff9008ca14cc>] bus_for_each_drv+0x120/0x188
[<ffffff9008ca570c>] __device_attach+0x19c/0x2dc
[<ffffff9008ca586c>] device_initial_probe+0x20/0x2c
[<ffffff9008ca18bc>] bus_probe_device+0x80/0x154
[<ffffff9008c9b9b4>] device_add+0x9b8/0xbdc
[<ffffff9008dc7640>] spi_add_device+0x1b8/0x380
[<ffffff9008dcbaf0>] spi_register_controller+0x111c/0x1378
[<ffffff9008dd6b10>] spi_geni_probe+0x4dc/0x6f8
[<ffffff9008cab058>] platform_drv_probe+0xdc/0x130
[<ffffff9008ca5168>] driver_probe_device+0x51c/0x824
[<ffffff9008ca59cc>] __driver_attach+0x100/0x194
[<ffffff9008ca0ea8>] bus_for_each_dev+0x104/0x16c
[<ffffff9008ca58c0>] driver_attach+0x48/0x54
[<ffffff9008ca1edc>] bus_add_driver+0x274/0x498
[<ffffff9008ca8448>] driver_register+0x1ac/0x230
[<ffffff9008caaf6c>] __platform_driver_register+0xcc/0xdc
[<ffffff9009c4b33c>] spi_geni_driver_init+0x1c/0x24
[<ffffff9008084cb8>] do_one_initcall+0x240/0x3dc
[<ffffff9009c017d0>] kernel_init_freeable+0x378/0x468
[<ffffff90096e8240>] kernel_init+0x14/0x110
[<ffffff9008086fcc>] ret_from_fork+0x10/0x18
The buggy address belongs to the page:
page:ffffffbf037791c0 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x4000000000000000()
raw: 4000000000000000 0000000000000000 0000000000000000 00000000ffffffff
raw: ffffffbf037791e0 ffffffbf037791e0 0000000000000000 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffffffc0dde47180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffffc0dde47200: f1 f1 f1 f1 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f2 f2
>ffffffc0dde47280: f2 f2 00 00 00 00 00 00 00 00 00 00 f3 f3 f3 f3
^
ffffffc0dde47300: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffffc0dde47380: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Let's leave around one unsigned int in the gpio_irq_chip struct for the
single parent irq case and repoint the 'parents' array at it. This way
code is left mostly intact to setup parents and we waste an extra few
bytes per structure of which there should be only a handful in a system.
Cc: Evan Green <evgreen@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Fixes: e0d8972898 ("gpio: Implement tighter IRQ chip integration")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
