Build an array that finds hardware CPU number from logical CPU
number in firmware CPU discovery. Use that rather than setting
paca of other CPUs directly, to begin with. Subsequent patch will
not have pacas allocated at this point.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fix SMP=n build by adding #ifdef in arch_match_cpu_phys_id()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move this into the early setup code, and don't iterate over CPU masks.
We don't want to call into sysfs so early from setup, and a future patch
won't initialize CPU masks by the time this is called.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fold in incremental fix from Nick for DSCR handling]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Split sparsemem initialisation from basic numa topology discovery.
Move the parsing earlier in boot, before pacas are allocated.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
slb_shadow structures are avoided for radix environment.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We no longer allocate lppacas in an array, so this patch removes the
1kB static alignment for the structure, and enforces the PAPR
alignment requirements at allocation time. We can not reduce the 1kB
allocation size however, due to existing KVM hypervisors.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change the paca array into an array of pointers to pacas. Allocate
pacas individually.
This allows flexibility in where the PACAs are allocated. Future work
will allocate them node-local. Platforms that don't have address limits
on PACAs would be able to defer PACA allocations until later in boot
rather than allocate all possible ones up-front then freeing unused.
This is slightly more overhead (one additional indirection) for cross
CPU paca references, but those aren't too common.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The "lppaca" is a structure registered with the hypervisor. This is
unnecessary when running on non-virtualised platforms. One field from
the lppaca (pmcregs_in_use) is also used by the host, so move the host
part out into the paca (lppaca field is still updated in
guest mode).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fix non-pseries build with some #ifdefs]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge our fixes branch from the 4.16 cycle.
There were a number of important fixes merged, in particular some Power9
workarounds that we want in next for testing purposes. There's also been
some conflicting changes in the CPU features code which are best merged
and tested before going upstream.
This disables the DAWR on all POWER9 CPUs via cpu feature quirk.
Using the DAWR on POWER9 can cause xstops, hence we need to disable
it.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This updates the ptrace code to use ppc_breakpoint_available().
We now advertise via PPC_PTRACE_GETHWDBGINFO zero breakpoints when the
DAWR is missing (ie. POWER9). This results in GDB falling back to
software emulation of the breakpoint (which is slow).
For the features advertised by PPC_PTRACE_GETHWDBGINFO, we keep
advertising DAWR as if we don't GDB assumes 1 breakpoint irrespective
of the number of breakpoints advertised. GDB then fails later when
trying to set this one breakpoint.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add ppc_breakpoint_available() to determine if a breakpoint is
available currently via the DAWR or DABR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Checking for a "fully active" device state requires testing two flag
bits, which is open coded in several places, so add a function to do
it.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The caller will always pass NULL for 'rmv_data' when
'eeh_aware_driver' is true, so the first two calls to
eeh_pe_dev_traverse() can be combined without changing behaviour as
can the two arms of the final 'if' block.
This should not change behaviour.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_reset_device() tests the value of 'bus' more than once but the
only caller, eeh_handle_normal_device() does this test itself and will
never pass NULL.
So, remove the dead tests.
This should not change behaviour.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is currently difficult to understand the behaviour of
eeh_reset_device() due to the way it's parameters are used. In
particular, when 'bus' is NULL, it's value is still necessary so the
same value is looked up again locally under a different name
('frozen_bus') but behaviour is changed.
To clarify this, add a new parameter 'driver_eeh_aware', and have the
caller set it when it would have passed NULL for 'bus' and always pass
a value for 'bus'. Then change any test that was on 'bus' to one on
'!driver_eeh_aware' and replace uses of 'frozen_bus' with 'bus'.
Also update the function's comment.
This should not change behaviour.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The name "frozen_bus" is misleading: it's not necessarily frozen, it's
just the PE's PCI bus.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove a test that checks if "frozen_bus" is NULL, because it cannot
have changed since it was tested at the start of the function and so
must be true here.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit "0ba178888b05 powerpc/eeh: Remove reference to PCI device"
removed a call to pci_dev_get() from __eeh_addr_cache_get_device() but
did not update the comment to match.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the EEH_PE_RECOVERING flag for a PE is managed by both the
caller and callee of eeh_handle_normal_event() (among other places not
considered here). This is complicated by the fact that the PE may
or may not have been invalidated by the call.
So move the callee's handling into eeh_handle_normal_event(), which
clarifies it and allows the return type to be changed to void (because
it no longer needs to indicate at the PE has been invalidated).
This should not change behaviour except in eeh_event_handler() where
it was previously possible to cause eeh_pe_state_clear() to be called
on an invalid PE, which is now avoided.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function eeh_handle_event(pe) does nothing other than switching
between calling eeh_handle_normal_event(pe) and
eeh_handle_special_event(). However it is only called in two places,
one where pe can't be NULL and the other where it must be NULL (see
eeh_event_handler()) so it does nothing but obscure the flow of
control.
So, remove it.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the pseries kernel advertises radix MMU support even if
the actual support is disabled via the CONFIG_PPC_RADIX_MMU option.
This adds a check for CONFIG_PPC_RADIX_MMU to avoid advertising radix
to the hypervisor.
Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a definition for cpu_show_spectre_v2() to override the generic
version. This has several permuations, though in practice some may not
occur we cater for any combination.
The most verbose is:
Mitigation: Indirect branch serialisation (kernel only), Indirect
branch cache disabled, ori31 speculation barrier enabled
We don't treat the ori31 speculation barrier as a mitigation on its
own, because it has to be *used* by code in order to be a mitigation
and we don't know if userspace is doing that. So if that's all we see
we say:
Vulnerable, ori31 speculation barrier enabled
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a definition for cpu_show_spectre_v1() to override the generic
version. Currently this just prints "Not affected" or "Vulnerable"
based on the firmware flag.
Although the kernel does have array_index_nospec() in a few places, we
haven't yet audited all the powerpc code to see where it's necessary,
so for now we don't list that as a mitigation.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have the security feature flags we can make the
information displayed in the "meltdown" file more informative.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This landed in setup_64.c for no good reason other than we had nowhere
else to put it. Now that we have a security-related file, that is a
better place for it so move it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This commit adds security feature flags to reflect the settings we
receive from firmware regarding Spectre/Meltdown mitigations.
The feature names reflect the names we are given by firmware on bare
metal machines. See the hostboot source for details.
Arguably these could be firmware features, but that then requires them
to be read early in boot so they're available prior to asm feature
patching, but we don't actually want to use them for patching. We may
also want to dynamically update them in future, which would be
incompatible with the way firmware features work (at the moment at
least). So for now just make them separate flags.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the rfi-flush messages print 'Using <type> flush' for all
enabled_flush_types, but that is not necessarily true -- as now the
fallback flush is always enabled on pseries, but the fixup function
overwrites its nop/branch slot with other flush types, if available.
So, replace the 'Using <type> flush' messages with '<type> flush is
available'.
Also, print the patched flush types in the fixup function, so users
can know what is (not) being used (e.g., the slower, fallback flush,
or no flush type at all if flush is disabled via the debugfs switch).
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For PowerVM migration we want to be able to call setup_rfi_flush()
again after we've migrated the partition.
To support that we need to check that we're not trying to allocate the
fallback flush area after memblock has gone away (i.e., boot-time only).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
rfi_flush_enable() includes a check to see if we're already
enabled (or disabled), and in that case does nothing.
But that means calling setup_rfi_flush() a 2nd time doesn't actually
work, which is a bit confusing.
Move that check into the debugfs code, where it really belongs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The SLB bad address handler's trap number fixup does not preserve the
low bit that indicates nonvolatile GPRs have not been saved. This
leads save_nvgprs to skip saving them, and subsequent functions and
return from interrupt will think they are saved.
This causes kernel branch-to-garbage debugging to not have correct
registers, can also cause userspace to have its registers clobbered
after a segfault.
Fixes: f0f558b131 ("powerpc/mm: Preserve CFAR value on SLB miss caused by access to bogus address")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Incremental linking is gone, so rename built-in.o to built-in.a, which
is the usual extension for archive files.
This patch does two things, first is a simple search/replace:
git grep -l 'built-in\.o' | xargs sed -i 's/built-in\.o/built-in\.a/g'
The second is to invert nesting of nested text manipulations to avoid
filtering built-in.a out from libs-y2:
-libs-y2 := $(filter-out %.a, $(patsubst %/, %/built-in.a, $(libs-y)))
+libs-y2 := $(patsubst %/, %/built-in.a, $(filter-out %.a, $(libs-y)))
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
POWER9 has hardware bugs relating to transactional memory and thread
reconfiguration (changes to hardware SMT mode). Specifically, the core
does not have enough storage to store a complete checkpoint of all the
architected state for all four threads. The DD2.2 version of POWER9
includes hardware modifications designed to allow hypervisor software
to implement workarounds for these problems. This patch implements
those workarounds in KVM code so that KVM guests see a full, working
transactional memory implementation.
The problems center around the use of TM suspended state, where the
CPU has a checkpointed state but execution is not transactional. The
workaround is to implement a "fake suspend" state, which looks to the
guest like suspended state but the CPU does not store a checkpoint.
In this state, any instruction that would cause a transition to
transactional state (rfid, rfebb, mtmsrd, tresume) or would use the
checkpointed state (treclaim) causes a "soft patch" interrupt (vector
0x1500) to the hypervisor so that it can be emulated. The trechkpt
instruction also causes a soft patch interrupt.
On POWER9 DD2.2, we avoid returning to the guest in any state which
would require a checkpoint to be present. The trechkpt in the guest
entry path which would normally create that checkpoint is replaced by
either a transition to fake suspend state, if the guest is in suspend
state, or a rollback to the pre-transactional state if the guest is in
transactional state. Fake suspend state is indicated by a flag in the
PACA plus a new bit in the PSSCR. The new PSSCR bit is write-only and
reads back as 0.
On exit from the guest, if the guest is in fake suspend state, we still
do the treclaim instruction as we would in real suspend state, in order
to get into non-transactional state, but we do not save the resulting
register state since there was no checkpoint.
Emulation of the instructions that cause a softpatch interrupt is
handled in two paths. If the guest is in real suspend mode, we call
kvmhv_p9_tm_emulation_early() to handle the cases where the guest is
transitioning to transactional state. This is called before we do the
treclaim in the guest exit path; because we haven't done treclaim, we
can get back to the guest with the transaction still active. If the
instruction is a case that kvmhv_p9_tm_emulation_early() doesn't
handle, or if the guest is in fake suspend state, then we proceed to
do the complete guest exit path and subsequently call
kvmhv_p9_tm_emulation() in host context with the MMU on. This handles
all the cases including the cases that generate program interrupts
(illegal instruction or TM Bad Thing) and facility unavailable
interrupts.
The emulation is reasonably straightforward and is mostly concerned
with checking for exception conditions and updating the state of
registers such as MSR and CR0. The treclaim emulation takes care to
ensure that the TEXASR register gets updated as if it were the guest
treclaim instruction that had done failure recording, not the treclaim
done in hypervisor state in the guest exit path.
With this, the KVM_CAP_PPC_HTM capability returns true (1) even if
transactional memory is not available to host userspace.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 processors up to and including "Nimbus" v2.2 have hardware
bugs relating to transactional memory and thread reconfiguration.
One of these bugs has a workaround which is to get the core into
SMT4 state temporarily. This workaround is only needed when
running bare-metal.
This patch provides a function which gets the core into SMT4 mode
by preventing threads from going to a stop state, and waking up
those which are already in a stop state. Once at least 3 threads
are not in a stop state, the core will be in SMT4 and we can
continue.
To do this, we add a "dont_stop" flag to the paca to tell the
thread not to go into a stop state. If this flag is set,
power9_idle_stop() just returns immediately with a return value
of 0. The pnv_power9_force_smt4_catch() function does the following:
1. Set the dont_stop flag for each thread in the core, except
ourselves (in fact we use an atomic_inc() in case more than
one thread is calling this function concurrently).
2. See how many threads are awake, indicated by their
requested_psscr field in the paca being 0. If this is at
least 3, skip to step 5.
3. Send a doorbell interrupt to each thread that was seen as
being in a stop state in step 2.
4. Until at least 3 threads are awake, scan the threads to which
we sent a doorbell interrupt and check if they are awake now.
This relies on the following properties:
- Once dont_stop is non-zero, requested_psccr can't go from zero to
non-zero, except transiently (and without the thread doing stop).
- requested_psscr being zero guarantees that the thread isn't in
a state-losing stop state where thread reconfiguration could occur.
- Doing stop with a PSSCR value of 0 won't be a state-losing stop
and thus won't allow thread reconfiguration.
- Once threads_per_core/2 + 1 (i.e. 3) threads are awake, the core
must be in SMT4 mode, since SMT modes are powers of 2.
This does add a sync to power9_idle_stop(), which is necessary to
provide the correct ordering between setting requested_psscr and
checking dont_stop. The overhead of the sync should be unnoticeable
compared to the latency of going into and out of a stop state.
Because some objected to incurring this extra latency on systems where
the XER[SO] bug is not relevant, I have put the test in
power9_idle_stop inside a feature section. This means that
pnv_power9_force_smt4_catch() WILL NOT WORK correctly on systems
without the CPU_FTR_P9_TM_XER_SO_BUG feature bit set, and will
probably hang the system.
In order to cater for uses where the caller has an operation that
has to be done while the core is in SMT4, the core continues to be
kept in SMT4 after pnv_power9_force_smt4_catch() function returns,
until the pnv_power9_force_smt4_release() function is called.
It undoes the effect of step 1 above and allows the other threads
to go into a stop state.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a CPU feature bit which is set for POWER9 "Nimbus" DD2.2
processors which will be used to enable the hypervisor to assist
hardware with the handling of checkpointed register values while the
CPU is in suspend state, in order to work around hardware bugs. The
hardware assistance for these workarounds introduced a new hardware
bug relating to the XER[SO] bit. We add a separate feature bit for
this bug in case future chips fix it while still requiring the
hypervisor assistance with suspend state.
When the dt_cpu_ftrs subsystem is in use, the software assistance can
be enabled using a "tm-suspend-hypervisor-assist" node in the device
tree, and a "tm-suspend-xer-so-bug" node enables the workarounds for
the XER[SO] bug. In the absence of such nodes, a quirk enables both
for POWER9 "Nimbus" DD2.2 processors.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves all the CPU feature bits that are only used on 32-bit
machines to the top 20 bits of the CPU feature word and arranges
for them to be defined only in 32-bit builds. The features that
are common to 32-bit and 64-bit machines are moved to bits 0-11
of the CPU feature word. This means that for 64-bit platforms,
bits 44-63 can now be used for new features that only exist on
64-bit machines. (These bit numbers are counting from the right,
i.e. the LSB is bit 0.)
Because CPU_FTR_L3_DISABLE_NAP moved from the low 16 bits to the high
16 bits, we have to adjust some assembly code. Also, CPU_FTR_EMB_HV
moved from the high 16 bits to the low 16 bits.
Note that CPU_FTR_REAL_LE only applies to 64-bit chips, because only
64-bit chips (POWER6, 7, 8, 9) have a true little-endian mode that is
a CPU execution mode as opposed to being a page attribute.
With this we now have 20 free CPU feature bits on 64-bit machines.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
All PowerPC CPUs other than the original PPC601 have a timebase
register rather than the "real-time clock" (RTC) register that the
PPC601 (and the original POWER and POWER2 CPUs) had. Currently
we have a CPU feature bit to indicate the presence of the timebase,
but it makes more sense to use a bit to indicate the unusual
situation rather than the common situation. This therefore defines
a CPU_FTR_USE_RTC bit in place of the CPU_FTR_USE_TB bit, and
arranges for it to be set on PPC601 systems.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On POWER9, under some circumstances, a broadcast TLB invalidation
might complete before all previous stores have drained, potentially
allowing stale stores from becoming visible after the invalidation.
This works around it by doubling up those TLB invalidations which was
verified by HW to be sufficient to close the risk window.
This will be documented in a yet-to-be-published errata.
Fixes: 1a472c9dba ("powerpc/mm/radix: Add tlbflush routines")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Enable the feature in the DT CPU features code for all Power9,
rename the feature to CPU_FTR_P9_TLBIE_BUG per benh.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
force_external_irq_replay() can be called in the do_IRQ path with
interrupts hard enabled and soft disabled if may_hard_irq_enable() set
MSR[EE]=1. It updates local_paca->irq_happened with a load, modify,
store sequence. If a maskable interrupt hits during this sequence, it
will go to the masked handler to be marked pending in irq_happened.
This update will be lost when the interrupt returns and the store
instruction executes. This can result in unpredictable latencies,
timeouts, lockups, etc.
Fix this by ensuring hard interrupts are disabled before modifying
irq_happened.
This could cause any maskable asynchronous interrupt to get lost, but
it was noticed on P9 SMP system doing RDMA NVMe target over 100GbE,
so very high external interrupt rate and high IPI rate. The hang was
bisected down to enabling doorbell interrupts for IPIs. These provided
an interrupt type that could run at high rates in the do_IRQ path,
stressing the race.
Fixes: 1d607bb3bd ("powerpc/irq: Add mechanism to force a replay of interrupts")
Cc: stable@vger.kernel.org # v4.8+
Reported-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It's slightly less error prone to use sizeof(*foo) rather than
specifying the type.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[mpe: Consolidate into one patch, rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The flush_dcache_phys_range() function is no longer used in the
kernel. The last usage was removed in c40785ad30 ("powerpc/dart: Use
a cachable DART").
This patch removes the function and declaration.
Signed-off-by: Matt Brown <matthew.brown.dev@gmail.com>
[mpe: Munge change log, include commit that removed last user]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A protection flag may not be valid across entire address space and
hence arch_validate_prot() might need the address a protection bit is
being set on to ensure it is a valid protection flag. For example, sparc
processors support memory corruption detection (as part of ADI feature)
flag on memory addresses mapped on to physical RAM but not on PFN mapped
pages or addresses mapped on to devices. This patch adds address to the
parameters being passed to arch_validate_prot() so protection bits can
be validated in the relevant context.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it just before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When running virtualised the powerpc kernel is able to run the system
in "compat mode" - which means the kernel and hardware are pretending
to userspace that the CPU is an older version than it actually is.
AT_BASE_PLATFORM is an AUXV entry that we export to userspace for use
when we're running in that mode, which tells userspace the "platform"
string for the real CPU version, as opposed to the faked version.
Although we don't support compat mode when using DT CPU features, and
arguably don't need to set AT_BASE_PLATFORM, the existing cputable
based code always sets it even when we're running bare metal. That
means the lack of AT_BASE_PLATFORM is a user-visible artifact of the
fact that the kernel is using DT CPU features, which we don't want.
So set it in the DT CPU features code also.
This results in eg:
$ LD_SHOW_AUXV=1 /bin/true | grep "AT_.*PLATFORM"
AT_PLATFORM: power9
AT_BASE_PLATFORM:power9
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
early_init() and machine_init() have no prototype, add one in
asm-prototypes.h.
Fixes the following warnings (treated as error in W=1):
arch/powerpc/kernel/setup_32.c:68:30: error: no previous prototype for ‘early_init’
arch/powerpc/kernel/setup_32.c:99:21: error: no previous prototype for ‘machine_init’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[mpe: Move them to asm-prototypes.h, drop other functions]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These functions can all be static, make it so.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[mpe: Combine a patch of Mathieu's with some other static conversions]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When neither CONFIG_ALTIVEC, nor CONFIG_VSX or CONFIG_PPC64 is
defined, the array feature_properties is defined as an empty array,
which in turn triggers the following warning (treated as error on
W=1):
arch/powerpc/kernel/prom.c: In function ‘check_cpu_feature_properties’:
arch/powerpc/kernel/prom.c:298:16: error: comparison of unsigned expression < 0 is always false
for (i = 0; i < ARRAY_SIZE(feature_properties); ++i, ++fp) {
^
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Two functions did not have a prototype defined in signal.h header. Fix
the following two warnings (treated as errors in W=1):
arch/powerpc/kernel/signal_32.c:1135:6: error: no previous prototype for ‘sys_rt_sigreturn’
arch/powerpc/kernel/signal_32.c:1422:6: error: no previous prototype for ‘sys_sigreturn’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
__giveup_fpu() is never called outside process.c, so it can be static.
That also means we don't need an empty definition in switch_to.h
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[mpe: Also drop the empty version, rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
