This allows for automatic output source switching in userspace. Enable
the pullup on the GPIO to actually make it trigger and mark it as
active-high since detection is reversed otherwise.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add mux so we can select either headset or built-in microphone input.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The codec is currently named after the chip but it should be named like
the device itself since otherwise it's impossible to distinguish it from
other devices using the same codec (e.g. in alsa's UCM).
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The board has it's own RTC chip which is backed by the (optional)
battery and hence preserves data/time on poweroff when that is inserted.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
BUCK3 needs a regulator-enable-ramp-delay since otherwise the board
freezes on etnaviv probe. With this pgc_gpu suspends and resumes as
expected. This must have been always broken since gpcv2 support was
enabled.
We also enable all the regulators needed for Deep Sleep Mode (DSM) as
always-on:
- VDD_SOC supplied by BUCK1
- VDDA_1P8 supplied by BUCK7
- VDDA_0P9 supplied by LDO4
- VDDA_DRAM supplied by LDO3
- NVCC_DRAM supplied by BUCK8
- VDD_DRAM supplied by BUCK5
Finally LDO5 and LDO6 provide VDD_PHY_1V8 and VDD_PHY_0V9 used by the
SOCs MIPI, HDMI and USB IP cores. While we would in theory be able to
turn these off (and I've tested that or LDO6 and mipi with USB disabled)
it is of little practical use atm since USB doesn't runtime suspend so
let's revisit this at a later point.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'interrupt-names' property is not described in dtschema, not used by
the driver and does not really make sense as its value is simple 'irq'.
Drop it to fix dtbs_check warnings like:
arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dt.yaml:
pmic@4b: 'interrupt-names' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:
... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PMIC node can be a clock provider (for its 32 kHz clock) and authors
of imx8mq-librem5-devkit.dts apparently wanted this because they added
input clock and clock-output-names.
Add necessary clock-cells to the PMIC node.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-and-tested-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename usb_typec to usb-typec to get a rid of a warning when building
dtb with warnings enabled.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the imx8mq data sheet running VDD_GPU at 0.9V is enough
when not overclocking to 1GHz (which we currently don't do).
Signed-off-by: Guido Günther <guido.gunther@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The IMU chip on the librem5-devkit is not mounted at the "natural" place
that would match normal phone orientation (see the documentation for the
details about what that is).
Since the lsm9ds1 driver supports providing a mount matrix, we can describe
the orientation on the board in the dts:
Create a right-handed coordinate system (x * -1; see the datasheet for the
axis) and rotate 180 degrees around the y axis because the device sits on
the back side from the display.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The poly fuses can handle 6V 4Amps so incease the kernel limts to 5V
3.5Amps.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
By adding broken-cd to the usdhc2 stanza the Redpine card can be
detected when the HKS is turned off and on.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Specify which regulator is used for cpufreq DVFS.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Connect the WoWWAN signal to a gpio key to wake up the system from suspend.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the simcom SIM7100 modem and the sai6 interface that connects it.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the sgtl5000 of the librem 5 devkit in devicetree.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Without a VBUS supply the dwc3 driver won't go into otg mode.
Fixes: eb4ea0857c ("arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit")
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Support for the vcnl4040 landet a while ago so add it and the
corresponding pinmux. The irq is currently unused in the driver so don't
configure it yet.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LSM9DS1 uses a high level interrupt.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Fixes: eb4ea0857c ("arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that there is driver support, describe the accel and gyro sensor parts
of the LSM9DS1 IMU.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The charge controller can handle 14V but the PTC on the devkit can only
handle 6V so limit the negotiated voltage to 5V.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is for the development kit board for the Librem 5. The current level
of support yields a working console and is able to boot userspace from
the network or eMMC.
Additional subsystems that are active :
- Both USB ports
- SD card socket
- WiFi usdhc
- WWAN modem
- GNSS
- GPIO keys
- LEDs
- gyro
- magnetometer
- touchscreen
- pwm
- backlight
- haptic motor
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
